New User Manuals
www.cda.eu CI921 Integrated Tumble Dryer Installation, use and maintenance
2 User information The room must be adequately ventilated to avoid the backﬂow of gases into the room from appliances burning gas or any other fuels. This includes open ﬁres. It is important to clean the lint ﬁlter after each drying cycle. Items that have been soiled with substances such as cooking oil, acetone, alcohol, petrol, kerosene, spot removers, turpentine, waxes and wax removers should be washed in hot water with an extra amount of detergent before being dried in the tumble dryer. Fabric softeners, or similar products, should be used as speciﬁed by the fabric softener instr..
3 ﬂammable substances in the tumble dryer. • Attempt to dry dripping wet articles. • Dry unwashed items in the tumble dryer. • Dry wool or wool mixture articles unless the article is labelled as suitable. This should avoid shrinkage. • Dry items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber backed articles and clothes or pillows ﬁtted with foam rubber pads. • Exhaust air must not be discharged into a ﬂue which is used for exhausting fumes from appliances burning gas or other fuels. • Allow the vent hose (where applicable) or ﬁlter to become b..
4 Important This appliance must only be used for the purpose for which it is intended, i.e. domestic use. Any other use could be dangerous and may lead to premature failure of the appliance. The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabi..
5 EU Declarations of Conformity: This appliance has been designed, constructed and marketed in compliance with safety requirements of EEC Directives 2006/95/ EEC & 2014/35/EU (Low voltage) and requirements of EMC Directives 2004/108/EEC & 2014/30/EU. This product is manufactured to comply with the radio interference requirements of the Council directives 82/336/EEC, 2004/108/EC & 2014/30/EU. IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2012/19/EU. At the end of its working life, the product must not be disposed of as urban waste. It m..
6 Use and controls 1. Programme selector: Choose the ﬁnal dryness of the load by selecting the desired dryness setting (see the programme chart). The dryer will stop automatically when the chosen dryness is achieved. 2. Heat settings: High – For fabrics insensitive to higher temperatures, such as cotton. Gentle – For temperature sensitive clothes. 3. Start button: Press to start the drying cycle. 4. Anti-crease active light When lit constantly, the neon indicates that the drying cycle is completed and clothes can be removed. To reduce creasing of clothes, anti-crease will automaticall..
7 Programme chart Programmes 1-7 can be operated on either full heat or half heat setting and include a 12 minute cool-down period at the end of the cycle, followed by the automatic anti-crease cycle. Programme 8 operates without the heater (regardless of the heat switch setting), circulating air through the dryer at the ambient temperature. Please note: the use of an iron dry programme will use 30% less energy than a cupboard dry programme Programme number Programme Description 1 Extra dry Clothes are dry enough to be put away 2 Cupboard dry Clothes are dry enough to be put away 3 Mid dry ..
8 To run a programme • Sort out the clothes into groups of similar fabrics and colours. Check the care label inside the garment. We suggest that a fabric conditioner be used to reduce static electricity. Delicate articles e.g. tights should be placed inside a pillowcase. It is better to dry small and large articles together. • Open the door. • Load clothes loosely into the drum. • Load sheets ﬁrst starting with one corner. • Close the door. • Dry your hands. • Switch on the machine. • Select correct heat position. • Set the programme to the required dryness setting. • ..
9 • The drum will begin to turn, and will stop when the clothes are dry. The drum will rotate clockwise and anti-clockwise during the programme alternately to reduce creasing. • There is an automatic 12 minute cool down period at the end of the cycle, during which the heater is switched oﬀ, to minimise creasing and prevent damage to the clothing. • After each programme, the dryer will run an anti-crease programme, rotating the drum brieﬂy every six minutes until the dryer is stopped or the door is opened. • Once the clothes are removed, clean the ﬁlter. • Switch oﬀ the ele..
10 Use and controls Should the clothes dry before the cycle has ﬁnished the thermostat will automatically switch oﬀ the heater to prevent over drying and save energy although the drum will still rotate. To stop the machine during the middle of a programme, open the door: the drum will stop rotating automatically and reset when you close the door. To restart the programme, press activate and then the start button. The ﬁnal part of the drying cycle occurs without heat (cool down cycle) to ensure that the items will not be damaged. Care labels you may ﬁnd on your fabrics: ‘Suitable f..
11 Suppliers name or trade mark CDA Model identifier CI921 Rated capacity at full load 7kg Appliance type Air Vented Energy efficiency class C Energy consumption of the appliance* 519kWh Automatic/non-automatic Automatic EU Ecolabel N/A E dry 4.39kWh E dry½ 2.38kWh Eg dry N/A Eg dry½ N/A Eg dry,a N/A Eg dry½,a N/A Off mode power (P o ) 0W Left on mode power (P l ) 0W Duration of left-on mode N/A T t 101mins T dry 135mins T dry½ 76mins Condensing efficiency class N/A C t N/A C dry N/A C dry½ N/A Sound power level 62dBA Built in/not built in Built in The standard cotton programme used at..
12 Care and maintenance Cleaning The Filter The ﬁlter is found, by opening the door (ﬁg.2.) and must always be in position when drying items in the appliance. To allow the dryer to operate eﬃciently the ﬁlter should be cleaned after each drying cycle. Do not be alarmed by the amount of lint deposited on the mesh. It is not due to excessive wear caused by the dryer but more an indication of its eﬃcient operation. All fabric loses lint when drying but it goes unnoticed into the air. In a tumble dryer it simply collects in the ﬁlter. After removing the dried clothes, clean the ﬁl..
13 Troubleshooting If the clothes are not dry after normal drying time: - Check that the ﬁlter is clean. - Check that you used the correct heat setting. - Check that the vent hose is not blocked (sometimes a strong wind may cause a back pressure). - Check that you have not set the timer within a cool down period. If your appliance does not work, check the following points before contacting CDA Customer Care • Check that there is power to the appliance. • Check that the machine is switched on and the door properly closed. • This appliance has a resettable cut-out. Check this has not ..
14 Installation / venting This appliance is fully compatible with any 600 mm deep kitchen units and complies with stringent EEC regulations. Your dryer is supplied with a vent hose which will extend to approximately 2.4m. We strongly recommend that this is vented through the wall with the attachment provided. The position of the hole (100 mm diameter) for the vent directly behind the tumble dryer is shown in ﬁg.3. If the vent through the wall is to be positioned anywhere other than behind the dryer, the vent hose should be positioned at ﬂoor level and through an adjacent side panel to a..
15 PLEASE NOTE: The air vent at the front of the appliance must never be covered or blocked in any way as this will impair the functioning of the appliance and could cause it to overheat. Fitting the décor door The hinges can be fastened through predrilled holes on either the left or right hand side with the door stops being fastened to the other side. ﬁg. 4 ﬁg. 5 80mm 600m m
16 Reversing the door The door on the dryer can be positioned either with the left or right hand hinging, as shown in ﬁg.6. Please note: power tools must not be used when reversing the door. How to reverse the door Open the door Undo screw A, remove switch strike B and replace screw A. Remove screws C and latch plate D. Remove hinge cover screw E. Close the door. Pull hinge cover F forwards to remove it. Remove two outer screws G. Remove door. Fit latch plate D with screws C. Reverse the door and ﬁt to the dryer in the closed position. Reﬁt screws G and hinge cover F. Open the door. F..
17 Electrical information Warning! This appliance must be earthed. The mains lead of this appliance has been ﬁtted with a BS 1363A 13 Amp fused plug. To change a fuse in this type of plug, follow the steps below: 1. Remove the fuse cover and fuse. 2. Fit replacement 13A fuse, ASTA approved to BS 1362 type, into the fuse cover. 3. Replace fuse cover. Important: Do not use the appliance without the fuse cover in position. How to connect an alternative plug If the ﬁtted plug is not suitable for your socket outlet, then it should be cut oﬀ and disposed of safely to prevent the risk of ele..
18 As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:- • The wire which is coloured GREEN and YELLOW must be connected to the terminal which is marked with letter (E) or by the Earth symbol or coloured GREEN and YELLOW . • The wire which is coloured BLUE must be connected to the terminal which is marked with the letter (N) , or coloured BLACK . • The wire which is coloured BROWN must be connected to the terminal which is marked with the letter (L) or coloured RED . If..
www.cda.eu Customer Care Department. The CDA Group Ltd, Harby Road, Langar, Nottinghamshire, NG13 9HY T: 01949 862 012 F: 01949 862 003 E: [email protected] For service or queries relating to your product please contact: The Customer Care Department on 01949 862 012 or email [email protected] For more information please contact: The Sales Department on 01949 862 010 or email [email protected]
Copyright © 2014 - 2019 Download User Manuals