WILDRIDGE LCC-104 Heritage Two Seat Glider Instruction Manual

WILDRIDGE LCC-104 Heritage Two Seat Glider

Product Information

• Specifications:
  • Product: Heritage Two-Seat Glider
  • Model: LCC-104
• Required Tools:
  • Mallet/Non-Marring Hammer (Do not use Metal Headed Hammer)
  • Cordless Drill
  • #2 Square Drive bit
  • 1/2 and 9/16 Wrench or Socket
• Hardware:
  • (4) 5/16 x 5 Bolts
  • (4) 5/16 x 3 1/2 Bolts
  • (2) 1/4 x 4 Bolts
  • (2) 1/4 Flange Nuts
  • (8) 5/16 Flange Nuts
  • (8) 3/8 x 2 1/2 Machine Bolts
  • (8) 3/8 Locknuts
  • (16) 3/8 Washers
  • (14) 3 Screws
  • (4) Glider Brackets
• Parts:
  • A = (1) Backrest
  • B = (1) Seat
  • C = (1) Right Arm/Leg Assembly
  • D = (1) Left Arm/Leg Assembly
  • E = (2) Base Pieces
  • F = (2) Cross Members

Product Usage Instructions

• Step 1: Assembly of Backrest, Seat, and Arm/Leg Assemblies
  • On a level surface, place the backrest (A) and the seat (B) on its side, butting them up against each other.
  • Lay the right arm/leg assembly (C) onto the backrest and seat and fasten them together using the following hardware:
  • For the front leg, use (2) 5/16 x 3 1/2 bolts and (2) 5/16 flange nuts.
  • For the back leg, use (2) 5/16 x 5 bolts and (2) 5/16 flange nuts.
  • For the armrest, use (1) 1/4 x 4 bolt and (1) 1/4 flange nut.
  • Repeat step 2 with the left arm/leg assembly (D) on the other side.
  • Fasten screws through the backrest into the seat support.
• Step 2: Attaching the Backrest to the Seat Support
  • Place the glider upright.
  • On the backside, fasten the backrest to the seat support using (2) 3 screws through the pre-drilled holes provided.
• Step 3: Assembly of Base Pieces and Cross Members
  • Pictured top left is a single base piece to use as a reference.
  • Please note the hole placement difference in the ends of both of the base pieces (E). Both base pieces will have the same hole configuration and should be placed so the matching sides on the base pieces are both facing the same direction.
  • One end of the base goes towards the front of the glider, and the other end will go towards the back of the glider.
  • The screws will go through the three holes that are to the left and three holes to the right of the pre-attached board on the base pieces. Do not put the screws in the holes on the top of the base pieces; those holes are for the glider bracket hardware used later.
  • Turn the base pieces (E) so the pre-attached boards face outward.
  • Place the cross members (F) into the notches on the base and attach them using (12) 3 screws, six per side.
  • Note: As noted in the first pic, the front of the base will be the front of the glider when you are assembling the base and glider in step 4.
• Step 4: Attaching Glider Brackets
  • Glider Bracket will curve away from the base.
  • Using (8) 3/8 x 2 1/2 machine bolts, (8) 3/8 washers, and (8) 3/8 locknuts, attach the glider brackets to the base as shown in the diagram.
• Frequently Asked Questions (FAQ)
  • Q: What tools are required for assembly?
    • A: The required tools for assembly are a mallet/non-marring hammer, cordless drill, #2 square drive bit, and 1/2 and 9/16 wrench or socket.
  • Q: How many base pieces are included?
    • A: Two base pieces are included.
  • Q: How many screws are needed to attach the backrest to the seat support?
    • A: Two screws are needed to attach the backrest to the seat support.
  • Q: How many glider brackets are included?
    • A: Four glider brackets are included.

Required Tools

• Mallet/Non-Marring Hammer (Do not use Metal Headed Hammer)
• Cordless Drill
• #2 Square Drive bit
• 1/2” and 9/16“ Wrench or Socket

Hardware

• (4) 5/16” x 5” Bolts
• (4) 5/16” x 3 1/2” Bolts
• (2) 1/4” x 4” Bolts
• (2) 1/4” Flange Nuts
• (8) 5/16” Flange Nuts
• (8) 3/8” x 2 1/2” Machine Bolts
• (8) 3/8” Locknuts
• (16) 3/8” Washers
• (14) 3” Screws
• (4) Glider Brackets

Parts

• A = (1) Backrest
• B = (1) Seat
• C = (1) Right Arm/Leg Assembly
• D = (1) Left Arm/Leg Assembly
• E = (2) Base Pieces
• F = (2) Cross Members

INSTALLATION STEPS

• Step 1
  • On a level surface, place the backrest (A) and the seat (B) on its side, butting them up against each other. Lay the right arm/leg assembly (C) onto the backrest and seat and fasten them together.
  • For the front leg use (2) 5/16” x 3 1/2” bolts and (2) 5/16” flange nuts.
  • For the back leg use (2) 5/16” x 5” bolts & (2) 5/16” flange nuts, and for the armrest use (1) 1/4” x 4” bolt & (1) 1/4” flange nut.
  • Repeat with the left arm/leg assembly (D) on the other side.

• Step 2
  • Place the glider upright.
  • On the backside, fasten the backrest to the seat support using (2) 3” screws, as shown, through th pre-drilled holes provided.
• Step 3
  • Pictured top left is a single base piece to use as a reference.
  • Please note the hole placement difference in the ends of both of the base pieces (E). Both base pieces will have the same hole configuration and should be placed so the matching sides on the base pieces are both facing the same direction.
  • One end of the base goes towards the front of the glider and the other end will go towards the back of the glider.
  • The screws will go through the three holes that are to the left and three holes to the right of the pre-attached board on the base pieces Do not put the screws in the holes on the top of the base pieces, those holes are for the glider bracket hardware used later.
  • Turn the base pieces (E) so the preattached boards face outward, then place the cross members (F) into the notches on the base and attach them using (12) 3” screws, six per side.
  • Note: As noted in the first pic, the front of the base will be the front of the glider when you are assembling the base and glider in step 4.
• Step 4
  • You will need (1) glider bracket and the hardware: (2) 3/8”x2 1/2” machine bolts, (4) 3/8” washers, and (2) 3/8” locknut.
  • This will be for the installation of one glider bracket in the front of the glider.
  • Using the picture above left as a reference, install the hardware and glider bracket to the front of the base (note where the hole placement is to determine the front of the base as shown in step 3).
  • For it to glide correctly the hardware must be placed in the order that is pictured above.
  • Using the glider bracket and the hardware, install the hardware through the top hole of the glider base and fasten to the glider bracket in the order shown.
  • Next, locate the glider assembly (seat/backrest/arm-leg assembly you put together earlier) and place it onto the base, as shown above right, then fasten the leg to the bottom of the glider bracket, installing the hardware in the order that is pictured above left.
  • Repeat this same process on the remaining three legs. Your glider is now complete.

MORE INFO

• 330-893-4212
• www.wildridge.com.
• HERITAGE TWO-SEAT GLIDER LCC-104

Documents / Resources

WILDRIDGE LCC-104 Heritage Two Seat Glider [pdf] Instruction Manual LCC-104 Heritage Two Seat Glider, LCC-104, Heritage Two Seat Glider, Two Seat Glider, Seat Glider, Glider

References

• User Manual