sw-motech logomounting instructions
LVG.05.934.11000/B
contains
LVG.05.934.10000/B
LVG.00.851.11000/B

MOUNTING INSTRUCTIONS

Item No.: LV6.05.934.10000/B
Revision: 00
Date: 05 – 2021
Lever Guard

Thank you for choosing this premium product from SW-MOTECH.
Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop!
SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly.
Nonconformance can lead to vehicle damage or even endanger the driver!
These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory partsis not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance.
Installed accessories can change the behaviour and/or stability of your vehicle.

GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/ operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that allitems of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key.
Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturers’ specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with medium-strength liquid thread locker.
Torque specifications undefined by SW-MOTECH must be obtained from the vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and connections previously removed are properly replaced. Also make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.

Packed by:
Date of packaging :

PARTS LIST

Step No. Item No./ Descriptionª Part Quantityb N•mc
2 (1) LVG.00.851.500.01 Lever Guard Set; 2 pieces 1/1
(2) LVG.05.934.001 Clamp Spacer, stepped; black 2/2
(3) LVG.01.903.002 Clamp Spacer; black 2/2
(4) M8 x 65; DIN 6912 Hexagon Socket Screw, short head 2/2 9
(5) Ø 8,4; DIN 125 Washer 2/2
4 (6) LVG.00.851.003 Cover Cap 2 /2
8.8 Coarse Thread Ø M4 M5 M6 M8 M10 M10
Steel CL8.8 N-m 2,8 5,5 9,6 23 46 79
10.9 Coarse Thread Ø M4 M5 M6 M8 M10 M10
Steel CL 10.9 N-m 4,1 8,1 14 34 67 115

Note: ª All measurements in millimeters. 8 The second number indicates the total quantity of the part in the delivery.
c No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.

sw-motech LVG05 SW Motech Honda Lever Guard

MOUNTING

sw-motech LVG05 SW Motech Honda Lever Guard - Parts

NOTE: The Installation is shown for the left side. The installation on the right side of the vehicle is analogous to the left side of the vehicle.
Remove the original handlebar end weights on both sides.sw-motech LVG05 SW Motech Honda Lever Guard - Parts 1Attach the parts (1) to (5) loosely together, as shown in the drawing
ATTENTION: Use liquid thread locker!sw-motech LVG05 SW Motech Honda Lever Guard - Parts 2sw-motech LVG05 SW Motech Honda Lever Guard - Parts 3

Insert the clamp spacers of the lever guards on both sides up to the collar in the open handlebar ends.
Now align the lever guards parallel to the ground.
Tighten the screws (4) so that the clamp spacers (2) and (3) are wedged in the handlebar tubes.
Tighten the screws (4) as specified.
ATTENTION: Check the proper fit of the Lever guards (1)!
Check all operations of all handlebar controls to ensure they are operating correctly! Make sure they are in accordance with the manufacturers’ specifications!
Pay attention to a full steer angle without the lever guards having contact with the vehicle!
Do not ride the vehicle if any controls are not operating correctly!sw-motech LVG05 SW Motech Honda Lever Guard - Parts 4sw-motech LVG05 SW Motech Honda Lever Guard - Parts 5

Insert the cover caps (6 ) on both sides into the openings of the mounted lever guards (1)

MOUNTING INSTRUCTIONS

Item No.: LV6.00.851.11000/B
Revision: 00
Date: 03 – 2021
Wind protection for lever guard

Thank you for choosing this premium product from SW-MOTECH.
Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop!
SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly.
Nonconformance can lead to vehicle damage or even endanger the driver!
These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory partsis not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance.
Installed accessories can change the behaviour and/or stability of your vehicle.

GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/ operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that allitems of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key.
Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturers’ specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with medium-strength liquid thread locker.
Torque specifications undefined by SW-MOTECH must be obtained from the vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and connections previously removed are properly replaced. Also make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.

Packed by :
Date of packaging :

Step No. Item No./ Descriptionª Part Quantity b N•mc
1 (1) LVG.00.851.005L /R Wind Deflector 2/2
2 (2) M4 x 8;1S0 7380 Lenshead Screw; black 4/4 0,5
8.8 Coarse Thread Ø M4 M5 M6 M8 M10 M10
Steel CL8.8 N-m 2,8 5,5 9,6 23 46 79
10.9 Coarse Thread Ø M4 M5 M6 M8 M10 M10
Steel CL 10.9 N-m 4,1 8,1 14 34 67 115

Note: All measurements in millimeters. ® The second number indicates the total quantity of the part in the delivery.
c No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.sw-motech LVG05 SW Motech Honda Lever Guard - Parts 6

MOUNTING

sw-motech LVG05 SW Motech Honda Lever Guard - Parts 7Insert on both sides the wind deflectors (1) to the lever guards.sw-motech LVG05 SW Motech Honda Lever Guard - Parts 8Attach the wind deflectors (1) to the lever guards.
ATTENTION: Use liquid thread locker, suitable for plastic (*: eg. Loctite 425)!
Carefully tighten the screws (2) as specified.
ATTENTION: Over-tightening the screws will damage the plastic parts!

sw-motech logo Errors and omissions excepted.
Technical and design modifcations are subject to change
Copyright by
SW-MATECH GmbH & Co. KG
Tel. / phone + 49 (0)6425 / 81468 – 050
Fax / fax + 49 (0)6425 / 8168 – 10
infofasw-motech.com
www.sw-motech.com 
SW-MOTECH GmbH & Co. KG
Ernteweg 7-10
35282 Rauschenberg  Germany

Documents / Resources

sw-motech LVG05 SW Motech Honda Lever Guard [pdf] Instruction Manual
LVG05 SW Motech Honda Lever Guard, LVG05, SW Motech Honda Lever Guard, Honda Lever Guard, Lever Guard, Guard

References

Leave a comment

Your email address will not be published. Required fields are marked *