Whirlpool-logo

Whirlpool AKZ 431-01-IX Convection Oven

Whirlpool-AKZ-431-01-IX-Convection-Oven-Product-Img

Recommendations

Important: Disconnect the oven from the mains before carrying out any installation work or servicing.

  • Installation must be carried out by a qualified technician in accordance with the manufacturer’s instructions and in compliance with local regulations.
  • Unpack the oven and make sure that the appliance has not been damaged during transport and that the oven door closes properly. If you are not sure contact the dealer or the nearest service centre.
  • After removing the oven from its packaging, leave it on the polystyrene base to prevent it from being damaged.
  • When installing the oven it is advisable to wear protective gloves.
  • Do not lift the oven by the door handle. Get hold of it using the side openings provided.

Preparing the housing unit

  • Kitchen units in contact with the oven must be heat resistant (80 °C min).
  • Cut the kitchen unit to fit before installing the appliance. Carefully remove any shavings or sawdust that could prevent the appliance from running properly.
  • The dimensions of the oven and unit are shown in Figures 1-2-3.
    Whirlpool-AKZ-431-01-IX-Convection-Oven-Img-1
  • To allow for proper ventilation, an opening should be left at the bottom of the kitchen unit. Pay attention to the dimensions in the diagram.
  • When installation has been completed, the bottom of the oven must be inaccessible. When installing, make sure that the sides of the oven do not touch the adjacent kitchen units (fig. 4-5).
  • When installing ovens under the worktop, leave a minimum clearance of 5 mm between the upper edge of the oven and the lower edge of the worktop (fig. 6). In order for the appliance to operate properly, this clearance must never be obstructed.
  • If the kitchen unit is not securely fixed to the wall, it must be anchored with standard brackets (G)(fig. 7) available on the market.
    Whirlpool-AKZ-431-01-IX-Convection-Oven-Img-2

Electrical connection

Regulations require that the appliance be earthed.

  • Connection to the mains must be carried out by a qualified electrician in accordance with the manufacturer’s instructions and in compliance with local regulations.
  • The installer is responsible for connecting appliances correctly to the mains and for observing the safety regulations.
  • The oven power cable must be long enough to connect the built-in appliance to the mains.
  • Observance of safety directives requires that a multi-pole switch with a minimum contact gap of 3 mm be used for the installation.
  • Do not use multiple plug adapters or extension leads.
  • After the oven has been installed, the electrical components must be inaccessible.

Connecting the oven to the power supply

  • Make sure that the voltage indicated on the rating plate is the same as the mains voltage. The rating plate is on the front edge of the oven (visible when the door is open).
  • If the oven does not have a power supply cable proceed as follows:
    1. Remove the two fastening screws of the terminal box cover located on the bottom part of the oven’s rear covering.
    2. Remove the cover to gain access to the terminal box and insert the power cable (see table) through the opening located on the bottom of the oven.
    3. Connect the cable to the terminal box, tighten the screws as far as they will go and secure it to the cable fastener.
    4. Put the cover back on by inserting the two blades in the slots and fasten it with the two screws.
      Whirlpool-AKZ-431-01-IX-Convection-Oven-Img-4

Securing the oven

  • Lift the oven getting hold of it by the openings on the sides and insert it into the housing unit, being careful not to trap the power supply cable (Fig. 8).
    Whirlpool-AKZ-431-01-IX-Convection-Oven-Img-3
  • Center the oven in the housing unit before securing it.
  • Make sure that the plastic spacers (if provided) are positioned correctly in the fastening holes. Then anchor the oven to the housing unit with the screws provided.

FAQ’s

What is the Whirlpool AKZ 431-01-IX Convection Oven?

The Whirlpool AKZ 431-01-IX Convection Oven is a kitchen appliance that uses convection technology to cook food evenly and efficiently.

What cooking modes does it offer?

The oven typically offers baking, roasting, grilling, and convection cooking modes to suit various recipes.

How does convection technology work in this oven?

Convection technology uses a fan to circulate hot air within the oven, ensuring even cooking and browning of food.

Can I adjust the temperature and cooking time?

Yes, you can typically adjust the temperature and cooking time using the oven's digital controls.

Does it have preset cooking options?

Yes, the digital display often includes preset cooking options for common dishes, making cooking more convenient.

Is the oven's interior lit during cooking?

Yes, the oven usually features interior lighting to help you monitor the cooking progress.

Is it easy to clean?

The oven's interior might feature easy-to-clean surfaces, and some models include a self-cleaning function.

Can I cook multiple dishes simultaneously?

Yes, the oven's spacious interior allows you to cook multiple dishes at once, making it convenient for meal preparation.

Is it suitable for baking bread and pastries?

Absolutely, the convection technology is excellent for baking bread, pastries, and other baked goods evenly.

What safety features does it have?

The oven commonly features a heat-resistant glass door and safety locks to prevent accidental opening during cooking.

Does it require professional installation?

While installation is often straightforward, it's recommended to follow the manufacturer's guidelines or seek professional installation for accuracy and safety.

References

Leave a comment

Your email address will not be published. Required fields are marked *