Frigidaire FFAD7033R1 Dehumidifier User Manual

Frigidaire FFAD7033R1 Dehumidifier User Manual

Important Safety Instructions

NOTE:
This USE & CARE MANUAL provides specific operating instructions for your model. Use the dehumidifier only as instructed in this USE & CARE MANUAL. These instructions are not meant to cover every possible condition and situation that may occur. Common sense and caution must be practiced when installing, operating, and maintaining any appliance.

WARNING
Avoid fire hazards or electric shock. Do not\ use an extension cord or an adaptor plug. Do not remove any prong from the power cord.

WARNING
For Your Safety Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Read product labels for flammability and other warnings. Discard water from a bucket. Water is not potable and cannot be used for drinking.

WARNING
Child Safety Precautions Destroy the carton, plastic bags, and any packing materials immediately after the dehumidifier is unpacked. Children should never use these items for play. Do not leave children unattended in an area where the appliance is operating. Do not allow them to sit or stand on the appliance.

Electrical Information

• For your safety and protection, this dehumidifier is equipped with a three-prong grounding plug on the power cord. Do not, under any circumstances, cut or remove the round ground prong from the plug.
• Your dehumidifier must be plugged directly into a properly grounded and polarized three-prong receptacle.
• lf the wall receptacle you intend to use will not accept a three-prong plug, or if you are not sure the outlet is adequately grounded or protected by a time delay fuse or circuit breaker, have a qualified electrician install the proper outlet according to the National Electrical Code and applicable local codes and ordinances.
• Do not use an extension cord or an adapter plug.
• Never unplug the dehumidifier by pulling on the power cord. Always grip the plug firmly and pull straight out from the receptacle.
• Do not pinch, bend, or knot the power cord.

SAFETY PRECAUTIONS

• This dehumidifier contains no user-serviceable parts. Always call an authorized Electrolux servicer for repairs.
• Do not insert or place fingers or objects into the air discharge area or rear grille of the unit.
• Do not start or stop the dehumidifier by unplugging the power cord or turning off the power at the electrical box.
• Do not cut or damage the power cord.
• If the power cord is damaged, it should only be replaced by an authorized Electrolux servicer.
• In the event of a malfunction (sparks, burning smell, etc.), immediately stop the operation, disconnect the power cord, and call an authorized Electrolux servicer.
• Do not operate the dehumidifier with wet hands.
• Do not pull on the power cord.
• Do not drink any water from the dehumidifier.

CAUTION!
Avoid Injury or damage to the unit or other property

• Do not direct airflow at fireplaces or other heat-related sources as this could cause flare-ups.
• Do not climb on or place objects on the unit.
• Do not hang objects off the unit.
• Do not place containers with liquids on the unit.
• Turn off the dehumidifier at the power source when it will not be used for an extended period. Operate the unit with air filter in place.
• Do not block or cover the intake grille, discharge area and outlet ports.
• Ensure that any electrical/electronic equipment is one yard away from the unit.
• Do not use or store flammable gases near the unit.

Installation, Location & How It Works

Selecting a Location

1. The dehumidifier must be operated in an enclosed area to be most effective. Close all doors, windows, and other outside openings to the room. The effectiveness of the dehumidifier depends on the rate at which new moisture-laden air enters the room.
2. Place the dehumidifier in a location that does not restrict airflow through the rear of the unit.
3. A dehumidifier operating in a basement will have little or no effect in drying an adjacent enclosed storage area, such as a closet unless there is adequate circulation of air in and out of the area. lt may be necessary to install a second dehumidifier in the enclosed area for satisfactory drying.
4. The dehumidifier must be installed on a level floor that will support it with a full bucket of water.
5. rance around the dehumidifier.

How It Works

• When the unit is started, the fan begins to pull moisture-laden air across the dehumidifying coils.
• The coils condense or draw moisture from the air, and air flows through the top louvers into the room as dry, warm air. Moisture removed from air is collected in a bucket on the rear of the dehumidifier.
• The unit is designed to operate between 41 °F (5 °C), and 90 °F (32 °C). The unit will not work properly if the temperature is out of this temperature range, or the performance of the unit will fall greatly.
• The “Compressor” circuit has an automatic 3-minute time delayed start if the unit is turned off and on quickly. This prevents overheating of the compressor and possible circuit breaker tripping.
• Make sure the tank is fitted correctly otherwise unit will not turn on.

Operating Instructions
Allow the unit to reach room temperature before operating. To begin operating the dehumidifier, follow these steps:

NOTE
The unit must be upright for one hour before operating.

1. Plug the power cord into a properly grounded 115-volt AC outlet.
   NOTE: If the “BUCKET FULL” light is on, remove the bucket and re-install it to reset the float switch.
2. Turn the unit on, and press the ON/OFF button. The unit will run in the factory setting of CONTINUOUS and high fan speed. In the CONTINUOUS mode, the unit will only display CO and not the room humidity. It is recommended you leave the unit running.
3. After a few days when the Relative Humidity has declined, press the HUMIDITY or buttons to choose a value between 35% to 85%, so the room is kept at a comfortable humidity. Pressing the or buttons will change the humidity selection in 5% increments. After you have set the desired humidity, the readout will display the actual room humidity. If at any time you want to return to the CONTINUOUS Mode, pressing the HUMIDITY button will lower the Relative Humidity through the 5% decrements until the display reads When the unit is in operation, pressing and button will simultaneously for 3 seconds can lock buttons. If this function is enabled, the LOCK indicator will illuminate and the display will show LC, which will blink for 3 times. Then room humidity will be displayed again. To disable this function, press and button simultaneously for 3 seconds and the LOCK indicator will turn off.
4. You can also use the FAN SPEED button to change the fan speed to HIGH, Medium or LOW. The indicator light will show the setting you have selected. A higher fan speed will result in quicker moisture removal.
5. The CLEAN FILTER light will illuminate after 250 hours of operation. At this time refer to the care and cleaning section to remove and clean the filter. Once the filter has been cleaned and replaced, simply press the FILTER button to extinguish the light.
6. The TIMER function enables you to either Delay Start or Delay Stop the unit in the choice from 0.5 hour to 24 hours. If the unit is running, then selecting Timer will turn the unit off in the hours that will be set (Delay Stop). If the unit is off, then selecting Timer will turn the unit on in the hours that will be set (Delay Start). TIMER setting: First press TIMER button, then adjust timer setting, by tapping or holding the or button to change the delay timer at 0.5 hour increments, up to 10 hours, then by 1 hour increments up to 24 hours. The control will count down the time remaining (8,7.5,7, etc.) until the unit either starts or stops.
7. For the Delay Start, the fan speed and humidity maintained will be the same as the previous setting. After the TIMER setting finishes, pressing the TIMER button again at any time will stop the TIMER function. The Delay Start/Stop Feature will work until the unit either starts or stops. Once that happens the above steps have to be repeated.
   1. Before entering TIMER setting, make sure power is being supplied to the unit.
   2. Before entering TIMER setting, make sure pressing or button sets one desired room humidity first.
8. To shut the unit down, press the ON/OFF button.After a power outage, the unit will memorize the last setting and return the unit to the same setting once power is restored.

Fault Codes

1. If the display reads “F1”, “F2” or “L1” error codes, please turn off and unplug the unit, then plug it in again in 30 minutes. If the unit malfunctions again, please contact your Authorized Frigidaire Service Center.
2. If the display reads “F0” , check the following operating conditions.
3. The outlet voltage should be 115V±10% and the surrounding temperature should be within the range of 41 °F (5 °C) to 90 °F (32 °C).
4. Unplug the unit and plug it in again under normal operating conditions. If the “F0” code persists, contact your Authorized Frigidaire Service Center.

Removing Collected Water

1. Emptying the Bucket:
2. When the bucket is full, the unit will shut down and the BUCKET FULL indicator will illuminate.
3. The product have also added bucket full indicator light to the front of the unit, this light will continually blink when the bucket is full, removed or not placed correctly.
4. Do not move the unit at this time otherwise water may spill on the floor.
5. Press sides of bucket gently to unclip the bucket from the unit.
6. Remove the bucket as shown in the photographs below and empty the bucket.

WARNING

•  You should hear a click when the bucket is in the correct position.
• If the bucket full light does not extinguish, check that the float is correctly snapped in place as indicated by the diagram.The foam embedded under the float(shown in the diagram below) is a functional part, which can not be removed.

Removing Collected Water (continued)

Continuous Drainage

• Open the drain cover at the side of the unit and take out drainage joint from the top of the styrofoam packaging. (fig.1)
• Screw the drainage joint onto the threaded portion of the drainage connector of the unit securely. (fig.2&3)
• Screw the garden hose onto the threaded portion of the drainage joint. (fig.4)
• Make sure the hose is secure so there are no leaks.
• Direct the hose toward the drain, making sure that there are no kinks that will stop the water flowing. (fig.5)
• When you want to remove the garden hose, prepare a drip tray (not supplied) to collect the water from the nozzle.(fig.6)

NOTE:

1. Screw the hose onto the drainage connector of the unit directly or through the drainage joint, continuous drainage option will automatically start.
2. Check the seal between the hose and the drainage joint. If there is a small leak then replace the hose gasket and re-tighten the hose.
3. It is recommended that a Dehumidifier Drain Hose – 11/16″ (17.5 mm) or larger be used.
4. When applying the continuous drainage option, place the dehumidifier on a horizontal surface and make sure the garden hose is clear of any obstructions and directed downward.
5. Improper installation or use of a hose may result in water filling up the bucket and causing the unit to shut off. Empty water bucket if shut-off occurs, then check the dehumidifier location and hose for proper installation. (fig.7)
6. To quit the continuous drainage option and collect water using the bucket, you need to remove the garden hose and take out the drainage joint to avoid leakage, then put the drain cover back.
7. If the bucket fills after a long period of continuous use, remove and check the hose for blockage by dirt.

Care and Cleaning & Storage

1. Filter
2. Remove the filter every two weeks based on normal operating conditions.
3. To remove the filter, pull the tabs and then take out the filter.
4. Wash the filter with clean water then dry. Do not dry the air filter with an electric hair dryer.
5. Once a filter is dry, replace on rear of unit and snap in place.
6. Cabinet
7. Dust cabinet with an oil-free cloth, or using a damp cloth.
8. Vacuum grill using a brush attachment.
9. Water Bucket
10. Clean bucket with warm water and detergent.

Storage

When unit is not in use, unplug and tidy up the cord as shown below.

Before You Call
Before calling for service, review this list. It may save you time and expense. This list includes common occurrences that are not the result of defective workmanship or materials in this appliance. If These Solutions Fail, Call 1-800-944-9044 For Frigidaire Service.

Download PDF: Frigidaire FFAD7033R1 Dehumidifier User Manual

References

• User Manual