Husqvarna-LOGO

Husqvarna 967 97 40-03 Automower 305 Robotic Lawn Mowers

Husqvarna-967 97-40-03-Automower-305 Robotic-Lawn-Mowers-

INSTALLATION INSTRUCTIONS

Placement of and connecting the Charging sectionHusqvarna-967 97-40-03-Automower-305 Robotic-Lawn-Mowers-1

  1. Place the charging station at a central position in the working area, with a lot of open space in front of the charging station and on a relatively horizontal surface.
  2. Connect the power supply’s low voltage cable to the charging station and the power supply.
  3. Connect the power supply to a 100-240 V wall socket.
  4. Place the robotic lawn mower in the charging station to charge the battery while the boundary wire is laid. Press the ON/OFF button for 3 seconds and make sure that the indicator lamp on the button is lit.

Placement of the boundary wire and the guide wireHusqvarna-967 97-40-03-Automower-305 Robotic-Lawn-Mowers-2

  1. Lay the boundary wire so that it forms a loop around the working area.
  2. Make an eyelet at the point where the guidewire will later be connected.
  3. Run the guidewire to the point on the boundary loop where the connection will be made. Avoid laying the wire at tight angles.

Connecting the boundary wire and the guide wire

  1. Narrow passages in the yard make it difficult for the robotic lawn mower to find the charging station. The robotic lawn mower can be lead to remote areas using the guide wire. The guide wire also helps the robotic lawn mower to quickly find the charging station.
  2. Lay the guidewire under the charging station and at least 2 m / 7 ft straight out from the front edge of the charging station.
  3. Open the connectors and lay the wire ends in the recesses on each connector.
  4. Press the connectors together using a pair of pliers.
  5. Cut off any surplus boundary wire. Cut 1-2 cm / 0.4-0.8” above the connectors.
  6. Press the connectors onto the contact pins, marked AL (left) and AR (right), on the charging station. It is important that the right-hand wire is connected to the right-hand contact pin, and the left-hand wire to the left-hand pin.
  7. Fasten the connector to the contact pin marked G1 on the charging station.Husqvarna-967 97-40-03-Automower-305 Robotic-Lawn-Mowers-3

Connecting the guidewire to the boundary wireHusqvarna-967 97-40-03-Automower-305 Robotic-Lawn-Mowers-4

  1. Cut the boundary wire with wire cutters at the center of the eyelet that was made in step B.2
  2. Connect the guidewire to the boundary wire using the accompanying couplers. Press the couplers completely together with a polygraph.
  • Green solid light Good boundary loop signal.
  • Green flashing light ECO mode is activated.
  • Blue flashing light Malfunction in the boundary loop.
  • Red flashing light Malfunction in the charging station’s antenna.
  • Red solid light Fault in the circuit board or incorrect power supply in the charging station. The fault should be rectified by an autho-rized service technician.Husqvarna-967 97-40-03-Automower-305 Robotic-Lawn-Mowers-5

Starting and stopping STARTING

  1. Open the cover by pressing the STOP button.
  2. Press the ON/OFF button for 3 seconds. When you do this for the first time, a start up sequence starts where you select a four digit PIN code among other things.
  3. Press the START button and close the cover.
    STOPPING
    Press the STOP button.

Adjusting the robotic lawn mower to suit the size of your lawn

The mowing results depend on the mowing time. Adjust the mowing time to suit your yard using the Schedule function. You decide what times during the day the robotic lawn mower is to work.
Use the Weather Timer function and the robotic lawn mower will automatically adjust the mowing time to the growth of the grass.

Maintenance

  • Press the ON/OFF button for 3 seconds to disable the product and check that the indicator lamp on the button is not lit before all work on the robotic lawn mower’s chassis, such as cleaning or replacing the blades. Replace the blades regularly for the best mowing result.
  • Never use a high-pressure washer to clean the robotic lawnmower. Never use solvents for cleaning. Clean the product with a brush or running water from a water hose.
  • All connections to the charging station (power supply, boundary and guide wire) must be disconnected if there is a risk of a thunderstorm.
  • Fully charge the battery at the end of the season before winter storage.

For more information and instructions, read the complete Operator’s manual on For more information and instructions, read the complete Operator’s manual on www.husqvarna.com..

Automower® Connect

  • Download the Automower® Connect app from AppStore or GooglePlay.
  • Sign up and specify an e-mail adress and a password to create a Husqvarna account.
  • Log in to your Husqvarna account in the app.
  • Select My mowers in the Automower® Connect app, and then select the plus sign (+).
  • Follow the instructions in the app.

Connectivity

  • Long-range cellular connectivity (Only with
  • Automower® Connect kit installed, available as accessory).
  • Short-range Bluetooth® connectivity (Automower® Connect@Home).
  • Device tracking (GPS) (Only with Automower® Connect kit installed, available as accessory).Husqvarna-967 97-40-03-Automower-305 Robotic-Lawn-Mowers-6

Documents / Resources

Husqvarna 967 97 40-03 Automower 305 Robotic Lawn Mowers [pdf] User Guide
967 97 40-03, Automower 305 Robotic Lawn Mowers

References

Leave a comment

Your email address will not be published. Required fields are marked *