Dynojet-PC6-23003-vPower-Commander-6-Husqvarna-LOGO

Dynojet PC6-23003 vPower Commander 6 Husqvarna

Dynojet-PC6-23003-vPower-Commander-6-Husqvarna-PRODUCT

INPUT ACCESSORY GUIDEDynojet-PC6-23003-vPower-Commander-6-Husqvarna-FIG-1

OPTIONAL ACCESSORY INPUTS

Map (Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You can switch on the fl y between these two base maps when you hook up a switch to the MAP inputs. You can use any open/close type switch. The polarity of the wires is not important.
Shifter (Input 1 or 2) Used for clutch-less full-throttle upshifts. Insert the wires from the Dynojet quick shifter into either Input 1 or Input 2. The polarity of the wires is not important. Set to Input 2 by default.
Speed If your application has a speed sensor then you can tap into the signal side of the sensor and run a wire into this input. This will allow you to calculate gear position in the Control Center Software. Once gear position is set up you can alter your map based on gear position and setup gear-dependent kill times when using a quick shifter.
Analog This input is for a 0-5v signal such as engine temp, boost, etc. Once this input is established you can alter your fuel curve based on this input in the Power Core software.
Launch You can connect a wire to either Input 1 or Input 2 and then the other end to a switch. This switch when engaged (continuity) will only allow the RPM to be raised to a certain limit (set in the software). When released, you will have full RPM.

WIRE CONNECTIONS

To input wires into the PC6 fi first remove the rubber plug on the backside of the unit and loosen the screw for the corresponding input. Using a 22-24 gauge wire, strip about 10mm from its end. Push the wire into the hole of the PC6 until it stops and then tightens the screw. Make sure to reinstall the rubber plug.
NOTE: If you tin the wires with solder it will make inserting them easier.Dynojet-PC6-23003-vPower-Commander-6-Husqvarna-FIG-2

INSTALLING THE POWER COMMANDER 6Dynojet-PC6-23003-vPower-Commander-6-Husqvarna-FIG-3

  1. Remove the seat.
  2. Remove the fuel tank.
  3. Using the supplied Velcro, attach the PC6 to the inner side of the right-hand side cover.
    Make sure to clean both surfaces with the supplied alcohol swab before attaching the Velcro.
  4. Attach the ground wire from the PC6 to the negative side of the battery.Dynojet-PC6-23003-vPower-Commander-6-Husqvarna-FIG-4
  5. Route the PC6 harness towards the throttle body going underneath the frame support.
  6. Unplug the stock wiring harness from the fuel injector.Dynojet-PC6-23003-vPower-Commander-6-Husqvarna-FIG-5
  7. Plug the PC6 wiring harness in line with the stock wiring harness and fuel injector.Dynojet-PC6-23003-vPower-Commander-6-Husqvarna-FIG-6
  8. Using the supplied Posi-tap, attach the GREY wire of the PC6 to the stock ORANGE wire of the main wiring harness plugged in at the ECU.
  9. This is the 3rd wire from the end, on the top row of the stock ECU connector. Reinstall the fuel tank and the seat.Dynojet-PC6-23003-vPower-Commander-6-Husqvarna-FIG-7
  10. Download the latest map files from our website at dynojet.com/tunes.

2191 MENDENHALL DRIVE, NORTH LAS VEGAS, NV 89081 – 800-992-4993 – DYNOJET.COM © 2008-2021 DYNOJET RESEARCH ALL RIGHTS RESERVED

Documents / Resources

Dynojet PC6-23003 vPower Commander 6 Husqvarna [pdf] Installation Guide
PC6-23003 vPower Commander 6 Husqvarna, PC6-23003 vPower, Commander 6 Husqvarna

References

Leave a comment

Your email address will not be published. Required fields are marked *