Charlton-Jenrick-LOGO

Charlton Jenrick 840 Polaris LED Electric Fire

Charlton-Jenrick-840-Polaris-LED-Electric-Fire-PRODUCT

Specifications

  • Model No.: Polaris 840/Polaris 1000/Polaris 1600
  • Supply Voltage: AC 230-240V 50Hz
  • Maximum power consumption: 1800-2000W
  • Power for flame effect:
    • Polaris 840: 26.8W
    • Polaris 1000: 27.5W
    • Polaris 1600: 45.5W
  • Power for mood light:
    • Polaris 840: 25W
    • Polaris 1000: 24W
    • Polaris 1600: 17W
  • Heat Output:
    • Nominal heat output (Pnom): 2000W
    • Minimum heat output (indicative) (Pmin): 1000W
    • Maximum continuous heat output (Pmax): 2000W
  • Auxiliary Electricity Consumption:
    • At nominal heat output (max): 12.5W
    • At minimum heat output (min): 12W
    • In standby mode (elSB): 0.8W
  • Type of heat output/room temperature control: Electronic room temperature control plus week timer.

Please read the instructions carefully before installation or use and keep them for future reference

IMPORTANT SAFETY INFORMATION

Read all of the instructions carefully before using the appliance.

  • For indoor use only. This appliance is not suitable for use outside the house and is only suitable for well-insulated spaces or occasional use.
  • Do not use this appliance in the immediate surroundings of a bath, a shower, or a swimming pool.
  • Do not use this fire as a free-standing appliance. It must always be fixed to the wall, fireplace mantel, floor, etc.
  • This fire must not be located immediately below a socket outlet.
  • This appliance must be earthed.
  • This appliance must not be supplied through an external switching device, such as a mer, or connected to the circuit that is regularly switched on and off by the utility to avoid a hazard due to the inadvertent rising of the thermal cut out.
  • If the power cord is damaged, it must be repaired by the manufacturer, its authorized service center, or a professional person.
  • Warning: to avoid overheating, do not allow the appliance to be covered or let the air inlet/outlet become obstructed. Please note the warning on the appliance.
  • To reduce the risk of fire, keep textiles, curtains, or any other flammable material at a minimum distance of 1 meter from the air outlet.
  • Keep the power cord away from hot surfaces and hot conditions. Do not route the power lead in front of the appliance.
  • Do not use this fire in rooms that have explosive gas in them (for example petrol), or if you are using solvents, glue, aerosol spray, or flammable paints, as these may catch fire.
  • This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
  • Children and vulnerable people must be supervised at all times when using this appliance, as some parts can become very hot and cause burns. A suitable fireguard must be found for this purpose.
  • Do not use this appliance in small rooms when they are occupied by persons not capable of leaving the room on their own unless constant supervision is provided.
  • Cleaning and user maintenance shall not be done by children without supervision.
  • Keep the power plug accessible after installation.

TECHNICAL SPECIFICATIONS

  • Model No.: Polaris 840/Polaris 1000/Polaris 1600
  • Supply Voltage: AC 230-240V 50Hz
  • Maximum power consumption: 1800-2000W
  • Power for flame effect:
Model No. Polaris 840 Polaris 1000 Polaris 1600
Power 26.8W 27.5W 45.5W

Power for mood light:

Model No. Polaris 840 Polaris 1000 Polaris 1600
Max Power 25W 24W 17W

Heat Output:

  • Nominal heat output (Pnom): 2000W
  • Minimum heat output(indicative) (Pmin): 1000W
  • Maximum continuous heat output (Pmax): 2000W
  • Auxiliary Electricity consumption:
  • At nominal heat output (max): 12.5W
  • At minimum heat output (min): 12W
  • In standby mode (elSB): 0. 8W

Type of heat output/room temperature control

Single stage heat output and no room temperature control No
Two or more manual stages, no room temperature control No
With mechanic thermostat room temperature control No
With electronic room temperature control Yes
Electronic room temperature control plus day timer Yes
Electronic room temperature control plus week timer Yes

PARTS AND HARDWARE

  • Unpacking the fire carefully, make sure that the appliance is intact with no signs of damage caused by transport and no part has been exposed to water. If in doubt, do not use the appliance and contact an authorized service center.
  • Keep plastic wrapping away from children.
  • Save the original packaging as this may be required in the event of a service complaint with the product.
  • Check that all parts are removed from the packing

Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-1 Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-2

APPLIANCE DIMENSIONS

Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-4

Tools Required
A screwdriver a spirit level and a drill will be needed.

Locating the Appliance
Your new electric fireplace may be installed virtually anywhere in your home. However, when choosing a location ensure that the general instructions are followed:

For best results, install out of direct sunlight.
If installing in an existing fireplace and chimney always block the chimney with fiberglass insulation or similar, to prevent it sucking air away through the appliance. Failure to do this may cause poor performance and loss of heat or make the appliance cut out

The appliance should be connected to an earthed electrical outlet and it must be easily accessible to allow disconnection.
The wires in the mains cable of this appliance are colored under the following code: Blue = Neutral. Brown = Live. Green/yellow = earth.

PREPARATION BEFORE INSTALLATION
The appliance can be installed in 3 different arrangements, the intended arrangements should be considered before starting the installation. They are as follows:

  • Single front aspect (This is where the appliance is installed so that only the front window is visible)
  • Duel aspect (this is where the appliance is installed so that the front and one of the side windows are visible)
  • Triple aspect (this is where the appliance is installed so that the front and both side windows are visible)

When you unpack the appliance, you will notice that the side plates have been fixed on the appliance. Remove them if you want the appliance to be dual or triple-aspect. Then take out the edging strips and fix them to any side where the side panel has been removed, which makes it easier to create a finishing edge for plasterboard or cladding

Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-5

Take out the edging strips and install them as shown below.

Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-6

Fix the edging strips with eight ST4*8 screws which are already on the appliance

Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-7

The main electric connection to the rear of the appliance is via a kele plug. It is very important that the plug is fully located in the socket and the plastic retention clip provided is tied securely by the screws provided. We further recommend that the power is turned on and the appliance is operated to check the function and prove the power connection is sound.

Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-8

If you intend to use mood lights, then you need to prepare the appliance before fixing the feature. Prepare as follows: (Note: Mood lights are an optional extra.)
Remove the two ST4×6 screws and the metal plate on the right lower side. Pull out the cable inside, and make the connections with the components, in accordance with the mood light instructions
Refit the plate with two ST4×8 screws and connect the mood light strip, various lengths available (max length 6 meters).

Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-9

Note: Compatible mood lights are available from Charlton & Jenrick Ltd., and other makes may not be suitable and will void the warranty.
when mood lights are fixed, they should be checked for operaon before the access is closed off by the installation

Installaon
The following is only given as a general guide because it can be installed in so many ways. Provided you ensure air can freely enter the top and boom. Ensure electric connections are safely made in accordance with the codes. A multitude of materials may be used from the framework and cladding.

All service work can be carried out via the front of the appliance, so no special access is
required.

Installation into a framework
Prepare the framework as picture:

Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-10

NOTE: Considerations must be given to ensure that air can enter the vents on the underside of the appliance and the top of the appliance.
The appliance is filled with feet to support the appliance. Please don’t block the underside between the feet.

Push the appliance into the framework and fold out the brackets on the top and lower edge of this appliance to secure it to the framework by ST 4*40 Rat-tail Screws.

Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-11

Installation of hanging on the wall

Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-13

Remove the top venison cover and bend the edges as shown below. Then, move forward 10mm based on the original installation position and fix the topvenlaon cove

Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-14

  • Measure from the lowest point of the appliance to the top edge of the wall bracket. Note: – the wall bracket is currently fixed to the rear of the appliance.
  • Remove the wall bracket from the rear of the appliance.
  • Add the height you require the base of the appliance to be from the floor to the earlier measurement.
  • Use this new measurement to mark the wall up from the floor surface.
  • Offer the top edge of the wall bracket to this mark and ensure it is horizontal using a spirit level.
  • Carefully mark through the holes in the wall bracket.
  • Use the marks to drill holes in to fix the wall bracket
  • Carefully hang the appliance on the wall bracket
  • Check the appliance’s front face is vertical (parallel to the wall)
  • if it does not pull the lower edge from the wall until vertical and note the distance from the rear to the wall at the base of the appliance.
  • Remove the appliance from the wall bracket and place it upside down on the floor
  • Fix the 2 pcs of the lower wall spacers with the screws provided, selecting to the hole that is closest spacing off the engine the dimension determined earlier
  • Carefully hang the appliance again on the wall bracket, and check it is now vertical.
  • If you are satisfied that the appliance is vertical then mark through bracket forwall fixings
  • Complete wall fixing by securing with ST5*40 screws.

Laying the fuel bed

  • Remove the front glass panels by removing the thumbscrews and lower fixing brackets and then remove the front glass by pulling forward and living out of position.

Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-15

  • After removing the glass front panel, turn on the flame effect of the appliance and you will see some groups of red lights on the boom of the back screen.
  • These are reflections of LED lights under the front edge of the fuel bed area. Place the black glass ember components provided tightly against the front edge which can block the reflection of the lights on the back screen.
  • When you are satisfied that very little reflection of these LEDs can be seen on the back screen, randomly place the remaining black glass ember components over the fuel bed area.
  • Now open the bag of vermiculite and sprinkle it between the black glass embers to cover the remaining visible sections of the fuel bed area.
  • Finally, take your me to poison the logs and bark pieces provided over the embers and create the arrangement to your own taste (all the logs will fit onto the appliance, but if you wish you can leave some off).
  • Satisfy yourself that you are happy with the arrangement before you replace the front glass panel.
  • The installation should now be completed

OPERATING INSTRUCTIONS

  • WARNING! Do not operate the appliance if it is damaged or has malfunctioned. If you suspect the appliance is damaged or has malfunctioned call a qualified service engineer to inspect the appliance and replace any part of the electrical system if necessary, before reuse.
  • WARNING! To reduce the risk of fire, keep textiles, curtains, or any other flammable material a minimum distance of 1 meter from the air outlet.
  • MAKE SURE the plug fits right in the outlet. Faulty wall outlet connections or loose plugs can cause the outlet to overheat.
  • Do not disconnect the power at the main supply while the appliance is running. Use the functions on the remote to turn the fire off and ensure the mains switch has been moved to the off position before disconnecting.

PREPARATION BEFORE USE
The appliance can be operated by both remote control and manual controls on the appliance.

NOTE: To use both remote and manual functions the manual on/off switch must be in the ‘ON’ position. To prevent the product from becoming too hot, there is a 10-second delay when turning on the heater and a 10-second delay when turning off the heater fan.

Batteries
Ensure that the handset batteries are new and inserted correctly. Main Power Switch

  • The mains power switch is located on the control panel located on the upper side of the heater box
  • Switch ON (—) before operating either the remote or manual controls.
  • A long beep is heard to indicate the fire is ready for use.

OPERATING INSTRUCTIONS

NOTE: The manual buon controls basic functions, not a full range of controls. Use the remote handset to carry out all functions.

  • The manual buttons are located at the upper of the appliance.
  • Press “LIGHTS ON/OFF” to turn on or turn off both the flame and mood light at the same me.
  • Press the “FLAME” button to select the color of flame (3 kinds) or return to the OFF position.
  • Press the “FUEL BED ” button to select the color of the fuel bed (13 kinds) or return to the OFF position.
  • Press the “SPEED ” button to select the speed of flame (5 kinds).

NOTE: The controls on the appliance will lose the memory for all Funcon songs when the switch is set to the Off Position.
When the remote runs out of power or when you change the batteries, only the flame function will lose memory and will not affect the mer songs, however, the clock may need adjusting.

MANUAL CONTROL PANEL

Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-16

NOTE: The manual buon controls basic functions, not a full range of controls. Use the remote handset to carry out all functions.

  • The manual buttons are located at the upper of the appliance.
  • Press “LIGHTS ON/OFF” to turn on or turn off both the flame and moonlight at the same me.
  • Press the “FLAME” button to select the color of flame (3 kinds) or return to the OFF position.
  • Press the “FUEL BED ” button to select the color of the fuel bed (13 kinds) or return to the OFF position.
  • Press the “SPEED ” button to select the speed of flame (5 kinds).

NOTE: The controls on the appliance will lose the memory for all Funcon songs when the switch is set to the Off Position.
When the remote runs out of power or when you change the batteries, only the flamenco will lose memory and will not affect the mer songs, however, the clock may need adjusting.

REMOTE CONTROLS

Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-17

NOTE: This is a thermostat remote control. The remote should be in the same room as the fireplace and placed on a flat surface. It must be placed away from the fire so the hot air will not blow on it and affect the thermostat reading.
The communication frequency between the fire and remote has already been set up. If you cannot use the remote with the fire, please follow instructions Step.6b37 to initiate this connection in point.

Standby for Remote Handset

  • The screen shown to the right is when the remote handset is in standby condition.Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-18

Turn on/of

  • Press Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-19 to turn on the flame effect, and turn off the flame effect and heater when in normal mode.Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-20
  • Press Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-19 to turn on/off the flame effect under daily and

Flame Effect

  • Press Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-22 to enter the flame effect adjustment screen.
  • Press the ‘←’ and ‘→’ button to select the 3 kinds of flame effects.Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-23
  • Press the ‘+’ and ‘-’ buttons to select the 5 brightness of flame effect and OFF songs.

Fuel Bed Color

  • Press Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-26 to enter the fuel bed adjustment screen.
  • Press the ‘←’ and ‘→’ button to cycle through the 13 colors of the fuel bed or a color-cycle mode.
  • Press the ‘+’ and ‘-’ buttons to select the 5 brightness of the fuel bed and OFF songs.Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-28

Mood Light

Note: If mood lights are not connected, please ensure the brightness is set to zero.

  • Press Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-29 to enter the mood light adjustment screen.
  • Press the ‘←’ and ‘→’ button to cycle through the 13 colors of mood light or a color-cycle mode.
  • Press the ‘+’ and ‘-’ buttons to select the 5 brightness of mood light and OFF signs.Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-30

Normal Mode
Normal control mode is factory set. If it is not, then press

M button until the logo Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-32 shows up at the upper right corner of the screen.Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-33

  • Press the ‘+’ and ‘-’ buon to adjust the temperature from 17℃ to 25℃ by 2 intervals
  • Press Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-34 button to turn on/off heat, Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-35OFF will show at the lower of the screen

NOTE: It is normal for the fan heater to stop running for periods of me. This happens because the room temperature is at or above the temperature set on the remote control. The heater indicator will be turned off at 10s if you have the flame ON. The heater indicator will stay ON if you use the heating function only.

Count Down Timer
NOTE: This song is only for normal mode. It allows the appliance to go on standby for a set period.

  • Press Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-36 to cycle through the sengs from Off and 0.5 hours to 9 hours. The mer logo and I will show it on the screen. The heater must be in the ON position.
  • The heater can be automatically run by using daily mer and weekly mer on the remote.Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-37

Set up Day, Time, and Comfortable temperature.

  • Press Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-21 to turn on the remote handset. Hold the button M for 3 seconds to enter the screen.
  • Press the ‘←’ and ‘→’ buttons to choose Day, Time, or your comfortable temperature. The character selected will be highlighted.Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-38

Pressing the ‘+’ and ‘-’ buon will adjust the number

  • Time: 24-hour system
  • Select your comfortable temperature from 15-25℃.
  • Temperature unit: ℃、℉

Daily Timer Heang
The following are preset heating periods, which can be altered if desired

  • 06:00 unl 08:30
  • 17:00 unl 22:00Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-39
  • Press M until D shows at the upper right corner of the screen, then enter the daily or heating mode
  • Hold the button Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-40 for 6 seconds to enter The daily mer seng. Max 3 med Heang periods for a day.Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-41
  • Press ‘←’ or ‘→’ to choose hour or minute, and press ‘+’ or ‘-’ to set the me.
  • Minute will increase/decrease by 15 minutes per press.
  • Hold Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-40 for 3 seconds or wait for 10 seconds to save and exit the hearing me period Setting.

Adjusng the set temperature

  • Press the ‘+’ or ‘-’ button to increase or decrease the temperature based on your comfortable temperature range.
  • ECO means 2℃ lower than your comfortable temperature Setting,
  • ECO- means 4℃ lower,
  • COMF+ means 2℃ higher,
  • COMF++ means 4℃ higher.
  • To check your daily mer sengs, pressCharlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-40.
  • If heang needs to be turned off, it will be necessary to go back to the Normal Mode to turn off.

Week Timer Heang
The following are preset heating periods, which can be altered if desired.

From Monday to Friday

  • 06:00 unl 08:30
  • 17:00 unl 22:00

From Saturday to Sunday

  • 06:30 unl 09:30
  • 11:00 unl 13:00
  • 17:00 unl 22:00

Press M until W shows at the upper right corner of the screen, then enter the weaker heating mode.
Hold Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-40 the button for 6 seconds to enter the week mer Setting.Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-42

  • Press ‘←’ or ‘→’ to move the cursor (a flashing underline), and press the Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-40 button in the corresponding week position to select (the character is highlighted), or cancel (the character is displayed normally) the current song. Several days can be selected together.
  • Press the ‘→’ button to move the cursor to me period Setting area. Press ‘←’ or ‘→’ to choose an hour or minute, and press ‘+’ or ‘-’ to set the number.
  • Max 3 heang periods for a day.
  • Minute will increase/decrease by 15 minutes per press.
  • Press the Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-40 to set the hearing me for the selected day(s) and return to the week line.
  • Hold for 3s or wait for 10s to save and exit the hean game period Setting.
  • PressCharlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-40, ‘←’ and ‘→’ to check your week Timer setting.
  • If heang needs to be turned off, it will be necessary to go back to the Normal Control Mode to turn off.Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-43

Advance Mode

  • Under the daily and weekly modes, Press Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-34 :
  • To turn the heater off when the heater is on during a preset healing period.
  • To turn the heater on when the heater is off in between preset heang periods.Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-44

Adapve Start Control

According to room temperature and set temperature, the heater will automatically come on in me to heat the room to the set temperature at the set me. For example, if your room is set to start at 18:00 and the temperature is set to 23°C, the fire will come on at 17:30 to ensure the room is 23°C at 18:00.

Window Open Detection
When the transmitter detects a rapid drop in room temperature, it will be judged as a window open, the warning icon will be displayed and the hearing will be turned off automatically.

Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-46

After the indoor temperature has risen or a manual override of the warning (by operating the remote control) has been done, the fire will return to a normal working state.

Set up the communication between the remote and the appliance
The operations below should be carried out before programming when changing to a new remote or in the event the appliance cannot be controlled by the remote:

  • Hold the reset button on the appliance for 3 seconds (penPoint may needed) until you hear 3 short beeps from the unit, release the button.
  • Press the Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-21 button on the remote, the programming is finished when you hear 1 long beep from the appliance.
  • Resetting the code for remote control is necessary if the appliance operates wrongly or the remote control does not operate correctly.
  • Open the back cover of the remote control.
  • Press the Reset button on remote handset.
  • Follow the steps 6b.37

Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-47

Resetting the Thermal Cut Out
The appliance is fitted with an Electronic Safety Control (E.S.). This is asafety device, which switches off the fire if, for any reason, the appliance overheats when covered. If the heater stops operating while the flame effect continues working normally, this indicates that the E.S. Control is in operation. The E.S. Control can only be reset after the appliance has cooled down, and the appliance has been reset. Re-setting of the E.S. Control proceeds is as follows:

  • Switch off the appliance (Manual On/Off switch) and leave it off for approximately 10-15 minutes.
  • Remove any obstruction to the fan heater outlet or fan blades etc. Make sure that the power supply is disconnected with the plug socket outlet while doing this.
  • Switch on the appliance and the E.S. Control will be re-set.
  • Ensure that the appliance is functioning correctly. If the E.S. Control operates again, the appliance should be checked by a competent electrician.

MAINTENANCE

Warning: Before any maintenance or cleaning of the exterior of the fireplace, the units should be disconnected from the power supply until it is cooled off.

Remote Handset Battery Replacement

  • When the batteries are at full power, the battery symbol will showCharlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-48
  • When the batteries are half full, the battery symbol will showCharlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-49
  • When the batteries are out of power and need replacing immediately, the battery symbol will showCharlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-50
  • Battery replacement is recommended after 1 year. The batteries are 1.5V alkaline AAA, batteries.
  • Dispose of old batteries at an appropriate recycling facility.

Cleaning the Fireplace

  • Cleaning or polishing products are not recommended. Fingerprints or other marks on the front glass panel can be removed by a piece of soft, damp, lint-free cloth with a good quality household glass cleaner. The front glass panel should always be completely dried with a clean, lint-free cloth or paper towel.
  • Caution: Abrasive cleaners should not be used on the glass panel. Liquids should not be sprayed directly onto any surface of the unit.

OTHERS

Environment
Meaning of crossed-out wheeled dustbin: Electrical appliances should not be disposed of as unsorted municipal waste. Separate collection facilities should be used in the disposal of electrical appliances. Con- tact your local government for the information about the available collection systems. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being. When old appliances are replaced by new ones, it is a legal obligation of the retailer to take back the old appliance for disposal at least free of charge.

This Tre compies win the state Standard EN 6035 and EN 635 2.30which covers the essential requirements of the Low Voltage Directive 2014/35/EU and the EMC standards EN 55014-1; EN 55014-2; EN 61000-3-2 and EN 61000-3-3 which covers the essential requirements of the European Electro Magnetic Compatibility 2014/30/EU, and the RED standards EN300220-2, EN301489-1, EN301489- 3 and EN6247 which covers the essential requirements of the European Radio Equipment Directive 2014/53/EU.

Control PCB Remote Control Receiver Remote Control Transmitter
Hardware: Hardware: RF290B V1.2 Frequency: ASK/OOK 433.92MHZ
RC01-047A01   Maximum transmit power: 10mW
Software: V1   Hardware:RF290A-TX-V1.3
    Software:V2.4.1

SERVICE PARTS LIST

Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-51

Charlton-Jenrick-840-Polaris-LED-Electric-Fire-fig

 

Charlton-Jenrick-840-Polaris-LED-Electric-Fire-FIG-52

WARRANTY FOR ALL ELECTRIC MODELS

  1.  Provided the appliance has been correctly installed according to instructions, Kemlan / Jetmaster guarantees the cost of
  2. years replacing parts connection therewith for 5 YEARS from the date of installation. Labor is covered for

THIS WARRANTY DOES NOT COVER

    1. Failure to comply with manufacturer’s operation instructions.
    2. Normal wear and tear or damage caused by incorrect installation.
    3. Any form of rust and/or corrosion to the painted finish of the heater.
    4. Damage caused by water ingress.
    5. Cost of removal of a defective heater or re-installation of a replacement heater.
    6. Failure to use fireplace components supplied by Kemlan Industries Pty Ltd./ Jetmaster Fireplaces Australia
    7. Cost of inspection for damaged heater.

CLAIMS 

  • Should any defects occur, contact the Kemlan / Jetmaster distributor from whom you purchased the heater.
  • Under this warranty, the defective parts will be repaired or replaced by Kemlan’s option, free of charge.’
  • The fireplace installation must comply with the relevant local statutes, ordinances, regulations, and by-laws.

PLEASE COMPLETE AND RETAIN THIS SECTION FOR YOUR RECORDS

  • Purchased from:————————
  • Address:————————
  • Date of Purchase:————————

FAQ

  • Q: Can this electric fire be used outdoors?
    • A: No, this electric fire is suitable for indoor use only and should not be used outside.

Charlton & Jenrick Ltd

Documents / Resources

Charlton Jenrick 840 Polaris LED Electric Fire [pdf] Instruction Manual
840 Polaris LED Electric Fire, 840, Polaris LED Electric Fire, LED Electric Fire, Electric Fire, Fire

References

Leave a comment

Your email address will not be published. Required fields are marked *