ROLL-N-LOCK-LOGO

ROLL-N-LOCK M-Series 2007 2021 Toyota Tundra

ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-PRODUCT

Product Information

  • The M-Series A-Series is a bed cover system designed for Toyota Tundra trucks. It is compatible with both the standard track and the XT Series track.
    The product is suitable for use with 2007-2021 Toyota Tundra models as well as the 2022+ Toyota Tundra models.
  • The installation sheet provides detailed instructions on how to install the bed cover system. It is important to ensure that all areas where the bed cover mounts are clean and free of debris before installing.
  • The kit includes various parts such as housing, track, cargo shield, drain tube, Tundra L bracket, threaded block, screws, washers, shims, rubber washer, butyl caulk strip, and Tundra L bracket (for 2022 Tundra installation).

Product Usage Instructions

  1. For installation with deck rail system:
    1. Unpack the tracks.
    2. Remove the (ST) track clamps. Discard the clamps.
  2. For installation without a deck rail system:
    1. Unpack the tracks.
    2. Remove the (T) track clamps. Discard the clamps.
  3. If there is no plastic bedliner, proceed to step 5. Measure from the inside of the tailgate along the top edge of the bedliner to each measurement provided for your specific bed size. Each mark indicates the centre of a 2×1-3/4 notch needed on the top edge of the bedliner.
  4. If there is no plastic bedliner, proceed to step 5. Measure from the inside of the tailgate along the top edge of the bedliner to each measurement provided for your specific bed size. Each mark indicates the centre of a 2×1-3/4 notch needed on the top edge of the bedliner.
  5. If there is no plastic bedliner, proceed to step 5. Measure from the inside of the tailgate along the top edge of the bedliner to each measurement provided for your specific bed size. Each mark indicates the centre of a 2×1-3/4 notch needed on the top edge of the bedliner.
  6. If there is no plastic bedliner, proceed with step 5:
    1. Remove the bulkhead deck rail. Discard the deck rail.
    2. Remove the bedliner.
    3. Mark on the tailgate protector where to cut and take the tailgate off to cut it.
  7. If there is no plastic bedliner, proceed with step 5:
    1. Using a tape measure, follow the measurements provided and mark on the bedliner where to cut.
    2. Use a jig saw to cut out the liner parts.
    3. Drill five 1/2″ holes where indicated. Discard the cut parts.
    4. Repeat on the driver’s side.
    5. Replace the bedliner and tailgate protector.

STANDARD AND XT SERIES

  • NOTE: Installation is the same for both the standard track and the XT Series track.
  • NOTE: Tailgate extrusion is NOT used with XT Series.ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-1ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-2 ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-3

NOTE: It is important that all areas where the bed cover mounts are clean and free of debris prior to installation.

TOOLS PROVIDED

  • l 1/4” Allen wrench
  • l 303® Vinyl protector

TOOLS REQUIRED

  • Jig saw
  • 1/2” Drill bit
  • Drill with Phillips’s head
  • Phillips screwdriver
  • Tape measure

PARTS INCLUDED IN YOUR KIT

  • A 1x Housing
  • B 2x Track
  • C 1x Cargo shield
  • D 1x Tailgate extrusion
  • E 2x Drain tube
  • F 4x Tundra “L” bracket (6x 6.5” ft Bed)
  • G 4x 1 x 2 x 1/4” Threaded block (6x 6.5” ft Bed)
  • H 2x #10-24 Screw
  • I 2x Cargo nut
  • J 5x #8 x 3/4” Self tapping screw
  • K 4x 5/16” Lock washer (6x 6.5”ft Bed)
  • L 4x 5/16” x 1” Cap screw (6x 6.5” ft Bed)
  • M 4x 1/4-20 x 1-1/4” Flat head black screw
  • N 4x 6m x 25mm Pan head screw  (6x 6.5” ft Bed)
  • O 2x 1/4-20 Lid screw (Taped to lid)
  • P 4x Black rubber washer
  • Q 4x 1/4-20 x 3/8” Screw
  • R 4x Shim (6x 6.5” ft Bed)
  • S 5x Black plastic shim
  • T 5x 5/16” x 3/4” Cap screw* (6x 6.5” ft Bed)
  • U 4x Shim (6x 6.5” ft Bed)*
  • V 4x 1/4” Flat washer (6x 6.5” ft Bed)* W 4x Butyl caulk strip*
  • X 4x Tundra “L” bracket (6x 6.5” ft Bed)*
  • Use for 2022 Tundra installation

INSTALLATION INSTRUCTION

  1. INSTALL WITH DECK RAIL SYSTEM – (1) Unpack tracks. (2) Remove the (ST) track clamps as shown (Discard clamps). ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-4
  2. INSTALL WITHOUT DECK RAIL SYSTEM – (1) Unpack tracks. (2) Remove the (T) track clamps as shown. (Discard clamps).ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-5
  3. INSTALL WITHOUT DECK RAIL SYSTEM – If there is No plastic bedliner proceed to step 5. Measure from the inside of the tailgate along the top edge of the bedliner to each measurement provided below for your specific bed size.
    • Each mark is the centre of 2”x1-3/4” notch needed on the top edge of the bedliner.ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-6
  4. INSTALL WITHOUT DECK RAIL SYSTEM – If there is No plastic bedliner proceed to step 5. Measure from the inside of the tailgate along the top edge of the bedliner to each measurement provided below for your specific bed size. Each mark is the centre of the 2”x1-3/4” notch needed on the top edge of the bedliner.ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-7
  5. INSTALL WITHOUT DECK RAIL SYSTEM – If there is No plastic bed liner proceed to step 5. Measure from the inside of the tailgate along the top edge of the bedliner to each measurement provided below for your specific bed size.
    Each mark is the centre of the 2”x1-3/4” notch needed on the top edge of the bedliner.ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-8
  6. INSTALL WITH DECK RAIL SYSTEM – If there is No plastic bedliner proceed with step 5. (1) Remove bulkhead deck rail. (Discard deck rail). (2) Remove the bedliner. (3) Then mark on the tailgate protector where to cut and take the tailgate off to cut it.ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-9
  7. INSTALL WITH DECK RAIL SYSTEM – If there is No plastic bedliner proceed with step 5. (1) Using a tape measure follow the measurements below and mark on the bedliner where to cut. Then use a jig saw to cut the liner parts out. Drill (5) 1/2” holes where indicated. (Discard cut parts). Repeat on the driver’s side. Replace the bedliner and tailgate protector.ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-10
  8. INSTALL WITHOUT DECK RAIL SYSTEM –If there is No plastic bedliner proceed with step 5. (1) Remove the bedliner. (2) Then mark on the tailgate protector where to cut and take the tailgate off to cut it.ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-11
  9. INSTALL WITHOUT DECK RAIL SYSTEM – If there is No plastic bedliner proceed with step 5. (1) Using a tape measure follow the measurements below and mark on the bedliner where to cut. Then use a jig saw to cut the liner parts out. Drill (5) 1/2” holes where indicated. (Discard cut parts). Repeat on the driver’s side. Replace the bedliner and tailgate protector.ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-12
  10. INSTALL ONLY – Remove rail channels at bulkhead and on the driver and passenger side.ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-13
  11. INSTALL ONLY – (1) Drill 1/2” hole through bulkhead as shown on driver and passenger side. DO NOT drill through the truck cab.
  12. Note: Rust protection should be used on the holes you drilled.ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-14
  13. INSTALL ONLY – (1) Press butyl strip (W) between the seam on driver and passenger side. (2) Drill 1/2” hole through existing hole in bed floor on driver and passenger side.ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-15
  14. INSTALL – Center the housing (A) between the bed rails, and up against the bulkhead on the driver and passenger side.ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-16
  15. INSTALL – Remove the lid from housing (A) by pushing toward cab (1) and up (2) on the driver and passenger side.ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-17
  16. INSTALL WITH DECK RAIL SYSTEM – Remove utility rail end caps (1) on both driver and passenger sides towards the tailgate. (Save end caps).ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-18
  17. INSTALL WITH DECK RAIL SYSTEM – Slide 1 x 2 x 1/4” threaded block (G) into the end of the deck rail system by the tailgate.

Note: It takes (2) two (3) of them depending on what size bed you have.ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-19

  • INSTALL WITHOUT DECK RAIL SYSTEM – Attach Tundra “L” bracket (F) with a 6m x 25mm pan head (N) fastener into the pre-drilled hole using a Phillips head screwdriver (1).
  • Note: It takes (2) to (3) of them depending on what size bed you have.ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-20
  • INSTALL ONLY – Attach Tundra “L” bracket (X) with a 6mx25mm pan head (N) fastener and 1/4” flat washer (V) into the pre-drilled hole using a Phillips head screwdriver (1).
  • Note: It takes (2) to (3) of them depending on what size bed you have.ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-21
  • INSTALL – (1) Turn the lock to 10 o’clock. (Do not remove plastic wing nuts). (2) Align tracks (B) onto the housing stem. (3) Make sure the edge of the tracks butt up against housing on driver and passenger side.ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-22
  • INSTALL WITH DECK RAIL SYSTEM – Loosely attach tracks (B) to 1 x 2 x 1/4” threaded block (G) using a 1/4-20 x 1-1/4” flat head screw (M) on driver and passenger side.
  • Note: It takes (2) to (3) of them depending on what size bed you have.ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-23
  • INSTALL – Secure tracks (B) to housing stem (1) on driver and passenger side using cargo nut (I) and #10-24 screw (H) using a Phillips screwdriver (2).ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-24
  • INSTALL ONLY – Lower the tailgate and insert (5) black plastic shims (S) beneath the inside flange of the tailgate cap.ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-25
  • INSTALL ONLY – (1) Holding the tailgate extrusion (D) assembly in place carefully. Holding the tailgate assembly square to the tailgate, use five (5) #8 x 3/4” self-tapping screws (J) to secure the centre hole, move to each end, press the assembly to the top of the tailgate making it conform to the D 1 contour of the tailgate, and secure it in place.ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-26
  • INSTALL ONLY – Close tailgate, shift the housing (A) back so the end of the tracks (B) are up against the tailgate on driver and passenger side.ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-27
  • INSTALL ONLY – Important to check track to track inside dimension, otherwise the cover will not latch properly on driver and passenger side.ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-28
  • INSTALL WITH DECK RAIL SYSTEM – The tracks should be at a 90o position on driver and passenger side. Tighten down the 1/4-20×1-1/4” flat head screw (M) and the 1 x 2 x 1/4” threaded block (G) with Phillips head screwdriver.ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-29
  • INSTALL WITHOUT DECK RAIL SYSTEM – Tighten the Tundra “L” bracket (L) with 5/16” lock washer (K) and 5/16” x 1” (5/16” x 3/4” for 22+) socket cap screw (L) 07-22) or (T) 22+) to the pre-installed track clamps using a 1/4” Allen wrench on driver and passenger side.
  • Note: When tight there may be a gap between the clamps, do not over-tighten.ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-30
  • INSTALL WITHOUT DECK RAIL SYSTEM – (1) If the angle and the track clamp do not line up, lift the track and shift angle to line up with Tundra “L” bracket (F) or (X). (2) If there is a space between track and angle, add supplied shim (R) or (U) between the angle and track.ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-31
  • Turn lock to 7 o’clock (1), remove plastic wing nut (2) and using both hands pull cover back to tailgate. (Discard plastic wing nut).ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-32
  • Replace lid on housing (A) by lining up the pin with the slot and pushing down (1) and toward tailgate (2) on driver and passenger side. Then install the 1/4” lid screws (O) with a Phillips screwdriver (3) on driver and passenger side.ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-33
  • To open cover pull back on the handle, turn the lock (1 & 2) to 10 o’clock and let the cover retract into the housing (A) while holding onto the pull strap (3).ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-34
  • Attach cargo shield (C) with the slots at the bottom of the housing (A) using two (2) black rubber washers (P) and two 1/4-20×3/8” screws (O) on the driver and passenger side.ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-35
  • INSTALL ONLY – Insert one end of the drain tube (E) through the drilled 1/2” hole feed toward the ground and insert the other end onto the housing fitting.
  • Make sure the drain tubes (E) are NOT aligned with or through the cab vents (1) on the driver and passenger side.
  • Note: Rust protection should be used on the holes you drilled.ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-36
  • INSTALL ONLY – Insert one end of the drain tube (E) through the drilled 1/2” hole and feed toward the ground and insert the other end onto the housing fitting.
  • Make sure the drain tubes (E) are NOT aligned with or through the cab vents (1) on driver and passenger side.
  • Note: You can use rust protection on the holes you drilled.ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-37
  • Attach the pull strap to the truck’s rear driver or passenger side rear tie-down towards the tailgate.ROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-38

IMPORTANT NOTICE

This bed cover may retract to the full open position very quickly resulting in any objects placed on top of the bed cover to fall off the bed cover or become trapped inside of the bed cover carrier. Do not place ANY objects on top of the bed cover when attempting to close. Failure to follow the instruction may result in damage to your vehicle, belongings or bed cover. To avoid injury keep all body parts clear of the bed cover and carrier when opening.

LIMITED WARRANTY

WARRANTY COVERAGE

  • This truck bed cover is warrantied against defects in materials or workmanship as follows. This warranty is void if the product has been damaged in an accident, or due to neglect, unforeseeable use, improper installation, improper servicing, or other cause not arising out of defects in material or workmanship.
  • The truck bed covers carries a limited warranty for three (3) years from the original date of purchase, subject to the terms below.

WARRANTY IS NOT TRANSFERABLE

  • The warranty is to the initial consumer purchasing the truck bed cover and it is not transferrable to a subsequent end user. Proof of purchase may be required to enforce these warranty rights.

WARRANTY CONDITIONS

  • Failure to follow these care and use instructions will void the warranty:
  • Clean with mild automotive soap and water only. Do not use any strong chemicals or cleaners. Lubrication of the rails with silicone or petroleum-based products will void the warranty.
  • Cargo must be secured at all points when the vehicle is in motion. Failure to adequately secure the cover or tether strap can result in damage and will void the warranty.
  • Check all clamps and retention mechanisms for tightness after a week of driving following installation (or re-installation) of the cover and periodically thereafter.
  • Before opening, the cover must be free of all foreign materials including snow and ice.
  • Do NOT tow your vehicle from the rear with the cover on your vehicle. If towing from the rear is required, the cover MUST be removed from the vehicle and properly stored.

WARRANTY PERFORMANCE

  • If all warranty conditions are met, a defective truck bed cover or hardware component will either be repaired or replaced (at our option). We reserve the right, for any warranty, to substitute a newer model or bed cover having a similar form and function, to offer a warranty discount on an entire replacement system, and/or to provide remedies other than those mentioned in this document.

WARRANTY RETURN

  • A Return Material Authorization number must be obtained from our Customer Service Department prior to returning any product.
  • We may require the original item to be returned postage prepaid for final determination. Shipping charges will apply for any repair or replacement.
  • Other than postage or shipping charges, no charge will be made for repair or replacement under this warranty.
  • his warranty gives you specific legal rights. As a consumer, you may also have additional rights and remedies under the laws of your state.
  • Register online at https://rollnlock.com/warranty-registration

REGISTER YOUR WARRANTY ONLINEROLL-N-LOCK-M-Series-2007-2021-Toyota-Tundra-FIG-39

COVER CARE AND MAINTENANCE

Vinyl Tops

  • Clean with mild automotive soap and water only. Do NOT use any strong chemicals or cleaners. Do NOT use conditioners that contain silicone or petroleum (e.g. Armor All®). We recommend using 303 Aerospace Protectant® to prolong the life of the vinyl.

Hard Tops

  • Clean with mild automotive soap and water only. Do NOT use any strong chemicals or cleaners. Use of wax or polish is not recommended.

Maintenance

  • It is recommended that you periodically check that the cover is securely attached to your truck bed. Inspect the clamps and front mounting bolts to ensure they were properly installed and have not come loose or knocked out of adjustment during operation.
  • Covers that are used with high frequency or that are subject to the vibrations and impact from rough roadways can cause the cover to require adjustment.
  • IMPORTANT: NEVER spray any lubricant into the tracks. THIS WILL VOID YOUR WARRANTY. Lubricants, especially silicone or petroleum-based, will attract dirt and debris which will lead to slow operation and will degrade the gaskets over time. If the tracks feel a little ‘sticky’, you may spray some 303 Aerospace Protectant® inside the track and wipe with a clean rag to remove any dirt or debris that has built up.

Housing Drains

  • To ensure proper drainage, it is recommended that the canister housing be checked and cleared of any leaves, twigs or other debris that may obstruct the drain tubes.
  • To remove the lid, first, make sure the Roll-N-Lock cover is fully closed and securely latched at the tailgate. Remove the Phillips head screw on each side of the lid and slide the lid slightly forward toward the cab to disengage the set pins. Once free, the lid can be lifted and removed from the canister. DO NOT ALLOW THE COVER TO RETRACT WITH THE LID REMOVED. This could allow the cover to retract too far into the canister causing damage to the cover.

USE

Opening and Using the Cover

  • Grasp the handle with one hand and pull it towards the tailgate to relieve pressure on the latches. At the same time, turn the tear-drop lock from the 7 o’clock latched position to the 10 o’clock unlatched position. Release the handle and the cover should begin to retract. The cover may require a slight push to get it started retracting. The tether strap can be used to control the speed of the cover as it retracts. Allow the cover to retract fully into the lid and this will reset the tear-drop lock to the 7 o’clock position.

Closing and Locking the Cover

  • Using the tether strap, gently pull the cover toward the tailgate. Once the cover handle is within reach, grasp with both hands, and pull the cover closed until it latches into place making sure that the tear-drop lock is pointed at the 7 o’clock position. Secure the tether strap inside the truck bed when latching. Forcing or slamming the cover back may damage the truck or cover.
  • Never close the cover with the tear-drop lock pointed at 10 o’clock as the latches will not engage properly. Always close the cover body with the tear-drop lock pointed at 7 o’clock. Failure to close the cover body correctly will result in the unit not latching.

SAFETY INSTRUCTIONS

  • DO NOT place objects on or against the cover or framework.
  • DO NOT tie cargo to the truck bed cover framework.
  • DO NOT operate the vehicle with objects on top of the cover body.
  • NEVER allow children or pets to occupy the truck bed while the cover is closed.
  • The cover is not airtight. Special care is required to keep cargo clean and dry.
  • Bed covers won’t prevent theft of contents inside the truck box.

TROUBLESHOOTING TIPS

  • The cover is slow to retract.
  • Spray 303® on a rag and wipe the top gasket in the track.
  • The cover does not latch.
  • Check track to track measurement.
  • Track tips up or down.
  • Use shim(s) behind the bracket to level the track.
  • The cover does not reach the tailgate.
  • Make sure the tracks are back against the tailgate.
  • Roll-N-Lock
  • 915 S Dixie Hwy, Pompano Beach, FL 33060
  • 800-952-7655
  • rollnlock.com © Roll-N-Lock, Corp., 2022
  • Any damaged or missing parts?
  • Parts will be shipped to you directly. Call 1-800-952-7655 Mon-Fri 8am – 5pm EST or email info@rollnlock.com

Documents / Resources

ROLL-N-LOCK M-Series 2007 2021 Toyota Tundra [pdf] Installation Guide
M-Series 2007 2021 Toyota Tundra, M-Series, 2007 2021 Toyota Tundra, Toyota Tundra, Tundra

References

Leave a comment

Your email address will not be published. Required fields are marked *