ADIUIVE 355-0075 60 Inch Ceiling Fans with Lights and Remote User Manual

Turn on the Bluetooth function of your phone.
Turn on the smart Life app on your mobile phone, turn on the wall power switch, and then long press the button on the remote control or wall control switch of the ceiling fan for about 4 seconds.

The ceiling fan emits a sound, enters networking mode, and presses Add Device.
Connect the ceiling fan device and click ADD.

The ceiling fan connection is ready, click Done.

FAQ

Q: Can I operate the ceiling fan with a wall dimmer switch?

A: No, an existing wall dimmer switch must be replaced with a single ON/OFF wall switch before installing the ceiling fan.

Q: How do I reset the codes for multiple devices or controller matching issues?

A: Press and hold a key for more than 3s to code the receiver powered in 10s. The light will twinkle once the controller codes with the receiver successfully.

Safety Instructions

Read all safety information and installation instructions before you begin to install the fan and save instructions.
All set screws of the fan must be checked and re-tightened where necessary before installation. To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets, balancing the blades, or cleaning the fan.
Do not insert foreign objects between rotating fan blades. Before changing the fan direction, turn off the fan and wait for the fan blades to stop completely.
The safeguards provided by these safety instructions and by the separate installation instructions are not meant to cover all possible conditions and situations that may occur.
It must be understood that common sense, caution, and care are factors that can not be built into this product.
These factors must be supplied by the person(s) installing, caring for, and operating the fan.

WARNING

To avoid the risk of electric shock, besure to shut off power at the main fuse or circuit breaker box before installing or servicing this fixture. turning off the electrical power by using the light switch is not sufficient to prevent electrical shock.
To reduce the risk of injury, install the fan so that the blades are at least 7 feet (2.3 meters)above the floor and at least 18 inches (0.5 meters)from the tip of the blades to the wall.
Toreducetheriskoffire, electric shock, or personal injury, mount to outlet box marked “acceptable for fan support” and use mounting screws provided with the outlet box.
The installation has to be under the national electrical code, ansinfpa70-1999, and local codes. If you are unfamiliar with the methods of installing electrical wiring, seek the services of a qualified licensed electrician.

Ceiling fan remote control is wired as shown in this wiring diagram

To avoid possible electrical shock be sure the power supply is turned off before wiring.
Risk of Fire product must be installed under the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
We strongly recommend that a professional electrician install all direct wire fixtures. For your safety, it is strongly recommended that two people install the ceiling fan.

Remote control and Wiring instructions

WIRING INSTRUCTIONS: Before doing wiring, ensure that you have all pole disconnections of the electricity supply.
Your fan is equipped with RF remote control and RF wall control.

The fan can be controlled by the remote control&wall control&mobile app.
You can find the unit in the box. Before wiring.

CODING RESET

If you have multiple devices or controller matching issues, please follow the steps below to reset the codes:

Press a hold on the key more than 3s to code the receiver powered in 10s.
The light will twinkle once the controller codes with the receiver successfully.

NOTE An existing wall dimmer switch must be replaced with a single ON/OFF wall switch before installing a Ceiling Fan to ensure consistent power ﬂow from the switch to the fan. You cannot operate our ceiling fan with a wall dimmer switch.

POWER PARAMETER LIST

Voltage	Fan	Led	Transmitter batteries
120V 60Hz	40W	12W,3 Color	AAA 1.5V x2 ( included )

Adopt the RF wireless digit emission technique

To avoid possible electrical shock be sure the power supply is turned off before wiring.

Risk of Fire product must be installed under the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
We strongly recommend that a professional electrician install all direct wire fixtures.
For your safety, it is strongly recommended that two people install the ceiling fan.

Transmitter function keys

APP Operating Instructions

Scan the QR code with the mobile phone to download the APP.

Connect your phone to the indoor WIFI network.
Turn on the Bluetooth function of your phone.
Turn on the smart Life app on your mobile phone, turn on the wall power switch, and then long press the button on the remote control or wall control switch of the ceiling fan for about 4 seconds.
- The ceiling fan emits a “didi” sound. The ceiling fan enters the networking mode, and finally press Click Add Device.
It shows that you can connect the ceiling fan device and click ADD.
The ceiling fan connection is ready, click Done.

Ceiling fan operation interface.

Ceiling fan operation interface

Package Contents

Unpack your fan and check the contents. You should have the following items.

Mounting Bracket x1
Canopy x1

Coupling Cover x1
Blade Cover x5
Downrod x1

Light Case x1
Lampshade x1
Motor x1

Fan Blade x5
Blade support x5
Remote control&Wall control

Assembly Kit
Installation Instructions

Dimension Reference

A. 1320mm
- B. 650mm

Exploded View Detail

INSTALLATION INSTRUCTIONS

IMPORTANT: BEFORE YOU BEGIN INSTALLATION, CAREFULLY READ ALL INFORMATION PROVIDED IN THE SAFETY INSTRUCTIONS AND INSTALLATION INSTRUCTIONS. IF IN DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
SAVE ALL INSTRUCTIONS.
NOTE: The fan weight is 17.64 lbs (8 kgs). Be sure the outlet box you are using is securely attached to the building structure and can support the full weight of the fan. Failure to do so can result in serious injury.

Installation Steps

Turn OFF the electrical circuit at the main fuse or circuit breaker box.
The mounting bracket must be securely fastened to the structural ceiling member.
Loosen parts at the yoke of the downrod assembly.

Assemble the Canopy and collar cap as shown in the figure.
Connect the suspension part to the fan motor.
Insert the connecting bolt into the suspender as shown in the figure.

Tighten the two screws on the color.
installdownrod (ball part) into a mounting bracket opening that is already securely fastened to a structural ceiling member.
Insert the receiver into the mounting bracket.

Fix the canopy on the Mounting Bracket and tighten the screws.
Assemble the blade, blade trim cover, and blade carrier according to the drawing and tighten the screws.
Install the blade on the fan host and tighten the screws.

Fixing the Light ket on the ceiling fan, tighten the three screws.
Install the glass othe in ket rotate
Turn on the electric power at the main fuse or circuit breaker box.

Troubleshooting

PROBLEM SUGGESTED REMEDY

1. If the fan does not start:	Check main and branch circuit fuses or circuit breakers. Make sure the forward/reverse switch is firmly in the bottom or top position. The fan will not operate when the switch is in the middle. Make sure that the wall control is turned “ON”. Check line wire connections to the fan and switch wire connections in the switch housing. CAUTION: Make sure the main power is turned off.
2. If fan sounds noisy:	Make sure all screws in the motor housing are snug. (not over-tightened) Make sure the screws which attach the fan blade bracket to the motor are tight. Make sure wire connectors in the switch housing are not rattling against each other or the interior wall of the switch housing. CAUTION: Make sure the main power is turned off before entering the switch housing. If using an optional ceiling fan light kit, make sure the screws securing the lampshade are finger-tight. Make sure the light bulb is tight in the socket and not touch the lampshade(s). If vibration persists from the lampshade, remove the lampshade and install a 1/4 in. wide rubber band on the glass neck to act as an insulator. Replace the lampshade and tighten the screws against the rubber band. Some fan motors are sensitive to signals from Solid State variable speed controls. DO NOT USE a Solid State variable speed control. Allow a “break-in” 24 hours. Most noises associated with a new fan will disappear after this period.
3. If fan wobbles:	All blades are weighed and grouped by weight. Natural woods vary in density which could cause the fan to wobble even though all blades are weight-matched. The following procedures should eliminate most of the wobble. Check for wobble after each step. Check that all blades are screwed firmly into blade holders. Check that all blade holders are tightened securely to the motor. Make sure that the canopy and mounting plate are tightened securely to the ceiling junction box and junction box is mounted firmly to a ceiling joist. Most wobble problems of fans are caused when blades are not at an equal level. To check the blade levels, select a point on the ceiling above the tip of any blade. Measure the distance from the ceiling to the blade tip, to an accuracy of 1/8 inch. Rotate the blades until the next blade is in the measuring position. Repeat measurement for each blade. If all blade levels are not equal, you can adjust blade levels by the following procedure. To adjust a blade tip down, insert a washer (not supplied) between the blade and blade bracket at the screw closest to the motor. To adjust a blade tip-up, insert a washer (not supplied)between the blade and blade bracket at the two screws farthest from the motor. Interchanging two adjacent blades could redistribute the weight and possibly result in smoother operation.
4. If light does not work:	Check the blue wire from the fan to make sure it is connected to the hot wire from the supply wire coming out of the ceiling. Check for loose or disconnected wires in the fan switch housing. Check for loose or disconnected wires in the light kit. heck for faulty light bulbs. CAUTION: Make sure the main circuit is turned off before entering the switch housing.
5. APP cannot be used	Check whether the router is powered on and whether the router network settings are correct. Whether the Bluetooth switch of the mobile phone is turned on. If the Bluetooth switch is not turned on, the APP cannot be connected, The connection sequence of the reinstallation manual shall be set again.

Documents / Resources

ADIUIVE 355-0075 60 Inch Ceiling Fans with Lights and Remote [pdf] User Manual
355-0075 60 Inch Ceiling Fans with Lights and Remote, 355-0075, 60 Inch Ceiling Fans with Lights and Remote, Ceiling Fans with Lights and Remote, Lights and Remote

References

User Manual