CombiSteel 7464.0015 Refrigerator Glass Door User Manual

This operation manual has been designed to facilitate the use of your single door cooler with maximum efficiency over the years. In all of the manufacturing processes “environmentally friendly” technologies are used as well as materials and refrigerants that are not harmful to the nature. Please read this manual carefully before you start operating your cooler in order to prevent user defects and ensure maximum efficiency from this product that has been manufactured to serve you over the years.

Detect the cooler immediately on delivery for any damage. In case of any damage, contact with your authorized dealer within 24 hours.

Attention: it requires a lapse of minimum 2 hours after any transportation before you start operating your cooler. If the cooler has remained in an environment where the temperature was below 0°C for a long period, allow for the compressor temperature to reach beyond +5°C before re-operating the cooler.

PRECAUTIONS AND SAFETY INSTRUCTIONS BEFORE THE INITIAL START-UP

Your cooler must be plugged certainly in an earthed wall socket.
Before operating the cooler, ensure that the mains socket is checked for proper earthing (grounding) and nominal voltage and frequency requirements by the authorized service staff or a qualified electrician. If the supply cord is damaged, it must be replaced by the manufacturer, or its authorized service or a similarly qualified person in order to avoid any hazard.

Do not use multi socket and extension cable.

The main power supply to which the cooler is connected must have a leakage current relay.
The nominal voltage and frequency requirements for the body are specified on the data plate.

Never make any repairs or carry out maintenance while the cooler is plugged in the mains socket.
Do not position the cooler in a place close to a source of strong heat or exposed to direct sunlight. Always remember that the UV lights in the sunlight deteriorates products in the glass door cooler. The appliance can be used in ambient temperature of max 32°C.

Unless otherwise stated, do not place your cooler to open areas where water can leak in.

Do not wash with pressurized water or hose when cleaning the product and its surroundings, use a wet cloth. Otherwise, the water which may intrude into the electrical components of the product can cause electric shock and fire risk.

Do not place your products in highly humid placed and/or places subject to corrosion.

Start the cooler on a level surface. Position in on the floor and make sure that it is level using a bubble gauge. If the cooler is found to tilt in one particular direction, please adjust the height of the corresponding leg until it is level. Then please move the cooler to the location where it will be used.

Do not relocate the cooler or move the cooler on its rollers while its loaded with product. If cooler is empty, please do not push the cooler to pass over cables or door frames, to avoid roller damages. Never push the cooler when the pavement is uneven, having inclination, or there are stairs nearby.

All the components that produce heat are located at the bottom part of your cooler.

Proper air circulation at this part is very important to ensure performance, therefore while positioning the cooler, allow minimum 10cm of space from the sides.

Do not let children get into and play around the body.

Keep the cooler key and plastic bags covering the accessories and the manual in a safe place out of reach of children.

Do not place any explosives and flammables in the cooler for safety reasons.

Leave the top of the cooler free, so that hot air from bottom can circulate effectively.

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way und understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

PLEASE CHECK YOUR REFRIGERANT GAS TYPE FROM THE RATING LABEL: R134A, R600A, R290 OR R744 (CO2)

Only for the models with R600A or R290 gas:
R600A/R290 gas is used in some models, explained in this instruction manual. R600A/R290 is an environmentally friendly gas and used in appliances which have effective cooling technology. This gas is flammable only under certain conditions. You must follow up the following rules if you wish to get normal operating conditions.

WARNING: keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.

WARNING: do not use mechanical devices or other means to accelerate the defrosting process.

WARNING: do not damage the refrigerant circuit.

WARNING: do not use electrical appliances inside the storage compartments of the appliance.

WARNING: in order to reduce flammability hazards, the installation of this appliance must only be carried out by a suitable qualified person.

Do not tangle with the device due to maintenance, repair or any other reasons other than authorized service.

Plug off the device against any possible freezing or icing and leave for defrosting.

Choose original components for all parts necessary for replacement on the product.

TECHNICAL FEATURES

Door
Power compartment
Shelf
Adjustable height
Interior ventilation fan
Canopy
Green light
Thermostat setting knob
Lighting switch
Fan switch
Interior lighting
Thermometer
Electronic thermostat (optional)

NOTE: The pictures given above are optional. They may vary due to models and versions.

Technical features	Operating temperature °C	Internal dimensions WxDxH (mm)	External dimensions WxDxH (mm)	Max. shelf load (net) Kg
7464.0015	+4/+10	430x456x774	500x580x865	31
7464.0085	+4/+10	490x447x1570	595x650x2000	41
7464.0088	+4/+10	490x447x1570	595x650x2000	41
7464.0090	+4/+10	490x447x1570	595x650x2000	41
7464.0093	+4/+10	490x447x1570	595x650x2000	41
7464.0094	+4/+10	490x447x1570	595x650x1850	41
7464.0095	+4/+10	490x447x1570	595x650x1850	41
7464.0200	+4/+10	450x497x2024	374x392x1408	23
7464.0205	+4/+10	450x497x1881	374x388x1441	23
7464.0210	+4/+10	374x551x1584	450x656x2024	23

Values specified above are given according to standard values and can vary by optional features.
Type label is located in the refrigerant part of the cabinet.
Please see the back page of the guide for the type label sample.

Climate Classes
Class	Temperature °C	Relative humidity %	Dew point °C
0	20	50	9,3
1	16	80	12,6
2	22	65	15,2
3	25	60	16,7
4	30	55	20
5	40	40	23,9
6	27	70	21,1
7	35	75	30
8	24	55	14,4

ASSEMBLING SINGLE DOOR COOLER / THE INITIAL START-UP

Air circulation at the rear is required for the coolers operate efficiently. Move the cooler backwards to place it properly. Allow minimum 10cm of space from the sides and the rear in order to ensure proper air circulation. Leva the top of the cooler free. Your cooler is now ready to plug in.

OPERATION

Avoid blocking air circulation inside the cooler, when loading the cooler with products. Otherwise undesired and extensive temperature variances may occur between the top and bottom compartments of the cooler.

Control panel:
Control panel consists of the following components depending on the model:

Green light (optional):
It is lit so long as the cooler is connected to the electric supply.

Thermostat setting knob (optional):
It is used to regulate the internal temperature of your cooler.

Thermostat adjustment is the most optimum adjustment in products with mechanical thermostat in factory defaults. It is recommended not to be replaced as long as it is not troubled with the internal product temperature. If you think that the product is not in desired temperature range you can make thermostat adjustment.

Thermostat setting must be done according to the features of the products to be preserved. Temperature setting can be done by means of turning the black thermostat knob on the control panel by the help of a coin or similar object. Turning the knob right decreases the internal temperature, whereas turning it left increases the internal temperature. Turning the knob left stops the compressor, which in turn stops the chilling process, although the electric current to the cooler is not cut off.

Internal ventilation fan switch (optional):
It used to provide air circulation inside the cooler.

Internal lighting switch (optional):
It is used to turn on or off the internal light of your cooler. If the light bulb does not function anymore, always unplug the cooler from the mains before replacing it. Pull up the lamp cover. Rotate the electric bulb 90 degrees, take it off and replace it with a new one. Always replace the starter whenever you replace the electric bulb.

Dismantling the illuminated advertisement panel (optional):
If it ever requires dismantling the illuminated advertisement panel, do the following:
The LEFT lid is screwed to the body and it is not possible to dismantle it from the outside. Therefore do not try to remove it. Advertisement panel is fixed to the RIGHT lid. Hold the right lid on the top and bottom sides and pull it RIGHTWARDS. The right lid will slide on the upper and lower tracks allowing the compartment to open. Once the compartment is open, carry out the needed (replacing the florescent lamps) and close the compartment by pulling the lid in the opposite direction.

Replacing the fluorescent lighting: (if your product has fluorescent lamp)
Before dismantling the lamp, always unplug your cooler. After dismantling the lamp cover inside the cooler, remove the lamp and always replace it with a lamp of the same features (length, power, etc.)

Unplug your visi-cooler.

Rotate the lamp 90°.
Remove the destroyed fluorescent lamp.
Place the new fluorescent lamp.

Rotate it 9o°.
Switch on your visi-cooler again.

WARNING:

Your cooler can have a fluorescent lamp. If the fluorescent lamp doesn’t illuminate or start blinking, please call technical service to repair it in a short while. Please do not remain your cooler white non-working lighting system.

Your cooler can have a LED illumination. If you face any problem with LED illumination, never try to repair it yourself. Inform an authorized service.

Mounting the shelves:

For Models With Option 1:

There are shelves shipped inside the cooler.
First insert the uppermost shelf in the uppermost hooks in the body Insert the others correspondingly with the same method. Chilling process in the body takes place through the internal air circulation. Therefore do not place the shelves very close to one another.

For Models With Option 2:

There are shelves and shelf supports shipped inside the cooler.

Carry out the following to mount the shelves:

Pilasters are numbered to provide height adjustment between the shelves in line with the product requirements. Place the shelf supports into corresponding notches on the pilasters. For an easy placement, use a pair of pincers to grip the support ends.
Lay down the shelves on the cooler floor. (Make sure that the right-angled (90°) side is at the rear).
Hold the uppermost shelf; tilt one side and place on the hooks on the corresponding supports.

Do the same for the remaining shelves and mount them all.
If present, place the bottom shelf on the base of the cooler.

ATTENTION:

Do not ever load anything on the base of your cooler. Always use bottom shelf.

Removing the pallet and inserting the feet
For models with metal sheet connectors. Your cabinet has been fixed with 4 metal brackets on wooden pallet before shipping. Please follow the instructions below before placing on its place.

Detach by unbolting 3 screws and remove metal bracket fixed cabinet and wooden pallet in front and back sections through a cutter device. Lean cabinet backwards from backside and remove pallet from underneath cabinet. Observe floor of cabinet and if not smooth, put product on scales.

For models without metal sheet connectors

Your Single Door cooler has been delivered on a wooden pallet, fixed to the body at four corners.
Please carry out the following to detach the pallet before the body is set in its final operating location:

Cut the 4 cable ties fixing to pallet to the cooler chassis by the means of a hand tool
Carefully detach the pallet from the body base. Please find the feet of the cooler provided interior. Insert them in the screwed sockets at the bottom of the cooler and make the height adjustment.

CAUTION: The adjustable legs on the front side of the cabinet should never be opened at the same time. Depending on the imbalance of the product, only one of the adjustable legs on the right or left side should be opened and the product should be balanced in this way.

SAFETY SHEET:
If you have a wheeled product, there are 2 safety feet on the front of your product.

ATTENTION!
Unless they are damaged and replaced by the same feet do not remove the safety feet under any circumstances! Never change the safety feet while the cooler is running! Change the safety feet by tilting the product towards the back or right side of the product. Never change the safety feet while the cooler is in the upright position.

ONLY AVAILABLE FOR MODELS HAVING A LEAKAGE CURRENT RELAY:

There might be a leakage current relay in the feeder cable of your refrigerator. To test if the leakage current relay works properly, press the yellow “TEST” button shown in following picture, the light will be off and the power of your refrigerator will be stopped when you press it . You can energize the refrigerator again by pressing “RESET” button. In case any leakage current, the power of your refrigerator will be stopped automatically. If your refrigerator does not work and the lamp connected to plug in cable and shown in following picture does not shine, press the “RESET” button. The light will be on when your refrigerator works. If your refrigerator does not work again, please apply to authorized service.

ONLY AVAILABLE FOR MODELS HAVING A VOLTAGE REGULATOR:

Voltage regulator of your refrigerator protects the unit against mains voltage fluctuations. When mains voltage fluctuates out of permissible range, voltage regulator turn off the power supply of the unit, end when mains voltage is back in the permissible range, the device will operate again. However, even in case mains voltage is back in permissible range instantly, the voltage regulator will turn on the power supply after a 3-minutes delay, to protect the device against voltage peaks and voltage dips.

Defrosting:
Your cooler is devised with an automatic defrosting system regulated by the thermostat. Defrost water accumulates in the channel underneath the evaporator; it is then carried to the drip tray by the help of a hose where it evaporates. After defrosting, clean the body and make sure to wipe it out leaving no moist inside. Plug the body again and reload the cooler after one hour.

CLEANING, MAINTENANCE AND TRANSPORTATION

To ensure higher efficiency, your cooler must be regularly cleaned. Never use any cleaning agent that contains alcohol, scouring powder or powerful solvents. Always remove the plug from the mains socket before cleaning the cooler. Add two teaspoons of baking soda (bicarbonate of soda) in 1 liter water and use the mixture to clean the cooler. Clean the outer part with a wet cloth and then wipe it out.
Attention: never use any hot water, electrical heater, sharp tools or similar things as they may ham the cooler.

Holidays/stop using for a while:
Do not unplug your cooler if you are going on a holiday or stop using it for a short time. If you are going on a holiday or stop using the body for a long time, unplug the cooler and empty it. After defrosting, clean the cooler and wipe it out with a cloth. Leave the door open to prevent odour in the cooler.

Transporting your cooler:
Before relocating the body, unplug it from the mains socket, defrost it, wipe the interior walls and floor with a damp cloth, place the plastic blockings between the glass door and the body and carry it in the normal position as it is used.

Attention: expansion gas (C-Pentane) is used in the insulation system of the cooler. When you dispose the body, it requires observing the applicable laws and rules of the country in which it is used. Cleaning / maintaining of your cooler’s condenser must be done at least two times in a year by authorized service.

TROUBLESHOOTING

If the cooler does not function:

Check if the cooler is properly plugged in the mains socket.
Check if there is electric current to the mains socket.
Check if the fuse has blown out.

Check if there is power failure.

If the cooler operates more frequently than desired:

Check if the door is opened very frequently or left open for a long time.

Check if the thermostat is set to chill more than desired.
Check if the compressor compartment is properly ventilated or compressor compartment needs cleaning.

If the cooler does not cool enough:

Check the temperature setting.
Check if the door is opened very frequently or left open for a long time.
Check if the internal air circulation is interrupted by overloading.

Cleaning/maintaining of condenser might not be done (please see Section 6).

If there is odour in the cooler:

Check if odorous stuff is openly stored.

Check if inside is properly cleaned.

After checking the above mentioned points and carrying out the recommendations, if your cooler still functions unsatisfactorily, contact the nearest authorized service centre, informing your complaints as well as the model and serial number of your cooler.

FOR MODELS WITH ELECTRONIC CONTROL SYSTEM

Our models with electronic control are designed with purpose of minimizing the energy consumption, and for that purpose they are equipped with special control systems. Your product is not only with thermostat control, it is equipped with a control system having feature of self-learning.

It is unfavourable to mount and dismount the magnetic door switches, motion sensor and other equipment by unauthorized people.

Control system is set so that refreshments should be kept at 3°C. This temperature value is the plant set temperature so that you can get the optimum efficiency from the cabinet and the ideal temperature recommended by refreshment producers.

Operating mode of electronic control system
The most important feature of the system is the self-learning module. It can sense conditions of the usage and when the selling point that the product is placed, is open or closed and it can control the operation characteristics in this direction. This features are provided by recording the properties as the density of the people around the cooler, frequency of opening and closing of the door of the apparatus, light level of the environment where the cooler is inside, with the help of the sensors.

Features that can be controlled by the control system
Control unit can open the lights of the cooler when the selling point is open and shuts off the lights when the selling point is closed. This feature shall operate after finishing the learning period of the control system. The light of the cooler shall be open until finishing the learning period. Please do not try to close it by yourself.

Control unit can control the inside evaporator fan. When the door is opened, inner fans are stopped. When the equipment is in stand-by mode, inner fan operates and stops with certain intervals. Stand-by mode refers the night or the hours that cooler is not used.
When the door of the unit is open for more than 2 minutes, control unit give signal. For this reason, it is normal to have signal during the loading of the refreshment. When the loading is finished, signal stops with closing of the door.

In stand-by mode control unit can lower the operation period of the compressor to the minimum levels.

Control unit applies defrost periods in certain intervals and it stops cooler system completely. After defrost operation, system turns normal condition again.

If there is a cooling defect in your cooler, control unit gives an alarm.

Operation steps
Start your cooler in morning hours and in working hours. It is important that the energy should not shut down during 48 hours.

Control unit shall start to learn working hours of the place it is in, and the operation characteristics of the cooler from the first day it operates. When the control unit can identify a stabile characteristic under operating conditions, it starts to control the cooler. This period is between 2 and 10 days.

When the learning mode is completed, control unit shall start stand-by mode after selling point is closed and after 30 minutes it shall turn off its lights. The next day, 3 hours before the opening of the shop, it shall pass to normal operating condition in order to keep the refreshments inside ready.

Important note:
Control unit shall compare the product using characteristic that is recorded and taken as reference with variable using characteristic continuously. In direction of periodic changes as seasonal changes and change of opening and closing hours of the shop, it shall learn and modify the program according to new conditions and control the cooler continuously.

Absolutely do not close the front part of the motion sensor otherwise cooler shall not sense the using frequency of the cooler.

Operation and screen information:
COMPRESSOR (compressor light): if green light is on, it shows that compressor is active. FAN (fan light): if green light is on, it shows that inner fans are active.
On screen of the control panel, symbols stated below can appear depending on the type of the trouble that may be formed and cooling mode of the cooler.

“USE” : your cooler is ready to use
“_ _ _” : your cooler is in stand-by mode
“888” : your cooler is in protection against freezing mode
“dO” : it shows that the door is open
“dEF” : system is in defrost mode
“rSF” : there is a problem at cooling system, contact your cooler maintenance
“SLO” : cooler is shut down because the voltage is low
“SHI” : cooler is shut down because the voltage is high
“Pf1” : input problem, contact your cooler maintenance

ATTENTION:
The defrost button can be used to set the cooler manually on defrost mode which will last for 10 minutes.

Description Production

PIR (motion detector)

Set button
Compressor LED
Fan LED

Perishable LED**
Motion LED
Up button*

Defrost button
Display
Down button*

Configuration port*

*These buttons are for service use only
**This LED has no function on this cooler

FOR CAREL ECOBOX AND CAREL ENERGY SAVING CONTROLLED MODELS

Control unit flashes for a few seconds in order to check if all connections are made correctly when the cooler is plugged in. This is normal, then the display will indicate current temperature. Set temperature has been adjusted to keep your beverages at optimum temperature, please do not attempt to change the settings.

Carel Ecobox
Carel Energy Saving Type 1

Carel Energy Saving Type 2

LIGHT: pushing at least 5 seconds the keypad, the light status will be toggled. Pushing the keypad, and before than the light status will be toggle, the display will show “On” or “OFF” in order to warn how the light status is going to change.

DAY/NIGHT MODE: the thermostat changes its mode automatically. If the door is continuously closed for more than 4 hours, the thermostat mode will be night and the lights of the cooler will be off. Lights can be on/off pushing the light button. If the door is opened at the night mode, the mode will be day. At the night mode your cooler consumes less energy. If you want to change the mode to the night you must push the day/night button. After 60 seconds from the pushing the mode will be night.

ECO MODE: pushing the keypad at least 3 seconds the ECO mode will toggle (if ECO mode is running then it will end, if ECO mode is waiting then it will start). Pushing the keypad, before then the ECO mode will toggle, the display will show “ECO” mode will toggle, the display will show “ECO” (Economy) or “nor” (normal) in order to warn how the functioning mode is going to change. If the thermostat is at the ECO mode, the cooler will consume less energy.

COMPLIANCE NORMS

Single door coolers described in this manual are manufactured and inspected in compliance with the TS EN ISO 23953-1, TS EN ISO 23953-2, TS EN 60335-2-89, IEC 60335-2-89, 2006/95/EC, 2004/108/EC.