FX3D DESIGN Toyota Camry Mud Guards Installation Guide

Contents hide

1 FX3D DESIGN Toyota Camry Mud Guards

2 Product Usage Instructions

3 PREPARING FOR INSTALLATION

4 Documents / Resources

4.1 References

5 Related Posts

FX3D DESIGN Toyota Camry Mud Guards

Specifications

Product: Mud Guards for Toyota Camry (2018-2023)

Manufacturer: FX3D Design
Website: shop.fx3ddesign.com

Product Usage Instructions

Preparing for Installation

A. Front mudguard (x2)

B. Rear mudguard (x2)
C. #8 x 3/4 (19mm) Phillips flat head screw (x4)

D. #12 x 25/32 (20mm) Truss head screw (x4)
E. U-nut #8 (x4)

F. Plastic grommet fastener (x4)
G. 3/16 (4.5mm) thick plastic spacer (x4)

H. 8mm plastic push-type fastener (x2)

Required tools

Utility knife
Screwdriver

Jack (for rear mudguard installation)

Front Mud Guards Installation – Part 1/2

Tips before the installation:
- Install mudguards with the logo facing the rear of the car.
- Pry open u-nuts before installing to prevent scratching the paint.
Turn your vehicle’s front wheels for access to the fender liner.

Remove factory fender liner clips and screws.
Pry open U-nuts and slide them onto Fender tabs.

Front Mud Guards Installation – Part 2/2

Insert screws through upper mudguard holes.

Align and screw in the mudguards, then tighten the screws.
Repeat steps on the other side of the vehicle.

Rear Mud Guards Installation – Part 1/3

Jack up the car to remove the rear wheel and access the bumper’s inner lip.

Remove plastic clips and pull the fabric liner to locate holes.

Rear Mud Guards Installation – Part 2/3

Insert grommets into holes and align the mudguards.
Insert screws through mud guard holes and spacers, then screw into grommets.

FAQ:

Q: Can the mudguards be installed without professional help?

A: Yes, the installation instructions are detailed, and with basic tools, you can install the mudguards yourself by following the provided steps.

Q: Are these mud guards compatible with all trim levels of the Toyota Camry?

A: Yes, the mudguards are designed to fit all trim levels of the Toyota Camry from 2018 to 2023.

Q: Can the mudguards be painted to match the car’s color?

A: While it is possible to paint the mudguards, we recommend consulting a professional to ensure a proper color match and finish

PREPARING FOR INSTALLATION

What’s in the package?

A. Front mudguard (x2)
B. Rear mud guard (x2)
C. #8 x 3/4” (19mm) Phillips ﬂat head screw (x4)
D. #12 x 25/32” (20mm) Truss head screw (x4)
E. U-nut #8 (x4)

F. Plastic grommet fastener (x4)
G. 3/16” (4.5mm) thick plastic spacer (x4)
H. 8mm plastic push-type fastener (x2)

Required tools

Phillips screwdriver or Electric drill
Utility knife

Car Jack
Wheel nuts removing socket and wrench

FRONT MUDGUARDS INSTALL – 1/2

Tips before the installation

Our mudguards should be installed with the logo facing the rear of the car.
Before installing the provided u-nuts, slightly pry them open with a ﬂat head screwdriver. Doing so will help to prevent scratching the paint when sliding them on.

A. Turn your vehicle’s front wheels as much as possible to allow access to the fender liner.
B. Remove the 2 factory fender liner clips and the 10mm hex screw shown in the image above. Gently pull on the fender liner to gain access to the fender tabs.
A. Grab 2 of the provided u-nuts(E) that came in the front mudguards package.

C. Slightly pry open each u-nut to facilitate the installation and avoid scratching the paint.
D. Slide the u-nuts on the two fender tabs making sure that the ﬂat face is facing towards the front of the vehicle and that the hole is correctly aligned.
A. Grab the front mud ﬂap (the FX3D logo should be facing the rear of the car).

B. Insert the provided screws(C) through the 2 upper mudguard slotted holes. The head of the screws should be resting on the opposite side of the FX3D logo.
C. Insert the factory 10mm hex screw into the bottom slotted hole.
D. Align and screw the 3 screws into the fender liner. Don’t tighten all the way to allow positioning of the ﬂaps to your liking.

E. When satisﬁed with the position, you can tighten all screws completely. Don’t over-tighten.
F. Repeat steps 1 to 3 on the other side of the vehicle.

REAR MUDGUARDS INSTALL – 1/3

A. Jack your car up so you can remove the rear wheel and gain access to the bumper inner lip and wheel well lining.
B. Remove the plastic clip shown in the image above.
A. Gently pull on the fabric liner to reveal and locate the 9mm square hole shown in the image above.

B. Using a utility knife, cut a hole through the liner making sure it’s aligned with the square hole.
TIP You can poke a hole from behind to ensure a perfectly aligned cut.

REAR MUD GUARDS INSTALL – 2/3

A. Insert a plastic grommet(F) in both holes.
Our mudguards are designed to ﬁt with or without the TRD rear bumper diffuser. Use the corresponding holes to match your car’s trim for a better ﬁtment
A. Grab the rear mud ﬂap (the FX3D logo should be facing the rear of the car).

B. Insert the #12 screws(D) through the mudguard slotted holes. Refer to the diagram shown below in Step 3.
The head of the screws should be resting on the opposite side of the FX3D logo.
C. insert a plastic spacer (G) into both screws as shown in the image above.

D. Align and screw the mudguards into the plastic grommets. Don’t tighten all the way to allow positioning of the ﬂaps to your liking.

REAR MUD GUARDS INSTALL – 3/3

A. When satisﬁed with the position of the ﬂap, tighten all screws completely. Don’t over-tighten.

B. Using a utility knife, cut a hole in the rear wheel well lining through the 3rd attachment point of the rear mudguard.
C. Insert one of the plastic push-type fasteners through the mudguard and the lining. Push on the fastener to secure it in place.
D. Repeat steps 1 to 5 on the other side of the vehicle.