TORQ RAV-MLE2 Toyota Rav4 Rear Molle Panels
Product Information
Specifications:
- Part Number: RAV-MLE2
- Manufacturer: Torq Engineering
- Compatibility: 2019+ Toyota RAV4
- Includes: Molle Panels Left and Right (Rear), M4 Rubber Well Nuts, M4 Stainless Steel Flanged Button Head
Product Usage Instructions
Installation Notes:
Rear Installation
- Align the Molle panel with the factory side panel and center punch or mark the mounting holes.
- Drill a small pilot hole then use a 5/16 Drill bit to redrill the holes.
- Insert Rubber Well Nuts into the drilled holes.
Frequently Asked Questions
Q: Can this suspension system be installed on any vehicle?
A: No, this suspension system is specifically designed for 2019+ Toyota RAV4 vehicles.
Q: Are there any safety precautions to consider when using this system for off-road purposes?
A: Yes, always wear your seatbelt and shoulder harness, operate the vehicle in a safe and conservative manner, and familiarize yourself with the special driving characteristics of the modified vehicle to prevent rollovers and ensure safety.
Notice to Dealer / Consumer
Important! Read all instructions before attempting any work on the vehicle.
Disclaimer Notice: Installing this suspension system on any vehicle implies that you are in agreement with the following term and conditions with respect to that vehicle, the vehicle owner, and any or all occupants of said vehicle at any time:
- Torq Engineering is not responsible, and cannot be held responsible for any conditions of said vehicle including, but not limited to the following: 1) Any and all adverse behavior, premature failure, or breakage caused by oversized tires and wheels, improper installation, failure to follow instructions, or any general negligence caused by installer or owner of said vehicle. 2) Any breakage or premature failure caused by racing or driver negligence. 3) Any incident determined to be caused by an increase height in said vehicle’s center of gravity. 4) Any incident determined to be caused by improper installation. 5) Any incident determined to be caused by a failure of materials.
- Torq Engineering is to be held harmless by the installer of this suspension component, owner of said vehicle, and any parties related directly or indirectly to said vehicle or owner of said vehicle. Torq Engineering is to be held harmless by all parties mentioned during the course of any and all circumstances or incidence resulting from the installation of this suspension component.
- It is not the intention of Torq Engineering that said vehicle be modified for use on public highways sanctioned by the Department of Transportation, or any state or local governing body. Vehicle owner accepts sole responsibility for ensuring that said vehicle is not in violation of local, state, or federal laws or vehicle code. Please check local vehicle laws and regulations before modifying your vehicle.
By installing this kit or having this kit installed on your vehicle, you are implying that you agree to the above terms and conditions. Please do not install this system if you do not agree.
WARNING:
- Vehicle modified for Off-road use may handle differently and vehicle may roll-over.
- Vehicles modified for off-road are generally not designed to improve cornering or maneuverability on the highway, therefore it is imperative to familiarize yourself and all operators of the vehicle of the special driving characteristics of the vehicle. Failure to operate vehicle in a safe and conservative manner may cause you, your passengers and third parties to suffer serious injury or even death if control is lost and vehicle overturns.
- Always wear your seatbelt and shoulder harness. Seatbelts not only help to protect occupants from injury but also keep the driver behind the wheel and in control when operating in rough terrain. Always remain on trails and observe conservation techniques while operating your vehicle.
2019+ TOYOTA RAV4 MOLLE PANELS (REAR) Bill of Materials
| 2 | Molle Panels Left and Right (Rear) |
| 11 | M4 Rubber Well Nuts |
| 11 | ½” x ½” Aluminum Spacer |
| 11 | M4 Stainless Steel Flanged Button Head |
INSTALLATION NOTES
- Inspect the contents of the kit and read the entire instructions before proceeding.
- We recommend this installation be performed by a qualified technician
- Torque all hardware to factory specifications
- We recommend using red Loctite on all bolts
Rear Installation
- Align the Molle panel with the factory side panel and center punch or mark the mounting holes.
- Drill a small pilot hole then use a 5/16” Drill bit to redrill the holes.
- Insert Rubber Well Nuts
- Install the ½” Aluminum spacers behind the molle panel and secure using the M4 Button head bolts.
Documents / Resources
 |
TORQ RAV-MLE2 Toyota Rav4 Rear Molle Panels [pdf] Instruction Manual RAV-MLE2 Toyota Rav4 Rear Molle Panels, RAV-MLE2, Toyota Rav4 Rear Molle Panels, Rav4 Rear Molle Panels, Rear Molle Panels, Molle Panels |
