SONY-Logo

SONY XLR-H1 XLR Handle Unit

SONY-XLR-H1-XLR-Handle-Unit-fig-1

Notes on use

  • For camera models compatible with this unit, visit the following website.
    In combination with any camera model manufactured by Sony that is not listed on the website, the unit does not work. https://www.sony.net/dics/h1/
  • Using this unit with products from other manufacturers may affect its performance, leading to accidents or malfunction.
  • This unit is not dust-proof, splash-proof, or waterproof.
  • To avoid the risk of a fire or an electric shock, observe the following:
    • Do not disassemble or alter this unit.
    • Do not use this unit with wet hands.
    • Do not allow ingress of water or foreign matters (metal, flammable substances, etc.) to this unit.
    • Do not use this unit in a place subject to water splashes, high humidity, dust, oil fumes, and steam.
  • To avoid the risk of damage or a malfunction, observe the following:
    • This unit is precision equipment. Do not drop the unit, hit it, or subject it to a strong physical impact.
    • Do not touch the electrical contacts on this unit with bare hands.
    • Do not use or store this unit in a place subject to high temperatures and humidity.
    •  When using this unit outdoors, keep the unit from exposure to rain or seawater.
  • For interior inspection and repair of this unit, contact your Sony dealer or local authorized Sony service facility

For Customers in the U.S.A.
For question regarding your product or for the Sony Service Center nearest you, call 1-800-222-SONY (7669).

Supplier’s Declaration of Conformity

  • Trade Name : SONY
  • Model : XLR-H1
  • Responsible Party : Sony Electronics Inc.
  • Address : 16535 Via Esprillo, San Diego, CA 92127 U.S.A.
  • Telephone Number : 858-942-2230

Identifying the Parts

SONY-XLR-H1-XLR-Handle-Unit-fig-2 SONY-XLR-H1-XLR-Handle-Unit-fig-3

  1. INPUT3 jack (stereo mini-jack, plug-in-power compatible)
  2. Release lever
  3. INPUT2 jack (3-pin XLR/TRS, female type, phantom-power compatible)
  4. INPUT1 jack (3-pin XLR/TRS, female type, phantom-power compatible)
  5. Microphone holder
  6. Cable holder
  7.  Micro USB port
  8. Attachment screws
  9. Multi Interface foot
  10. ATT (INPUT1) switch
  11. INPUT1 (LINE/MIC/MIC+48V) switch
  12. ATT (INPUT2) switch
  13. INPUT2 (LINE/MIC/MIC+48V) switch
  14. LOW CUT (INPUT1) switch
  15. AUTO/MAN (INPUT3) switch
  16. AUTO/MAN (INPUT1) switch
  17. AUDIO LEVEL (INPUT1) dial
  18.  AUTO/MAN/LINK (INPUT2) switch
  19. AUDIO LEVEL (INPUT2) dial
  20. LOW CUT (INPUT2) switch
  21. AUDIO LEVEL (INPUT3) dial
  22. INPUT SELECT switch
  23. HANDLE AUDIO switch

Notes

  • Before connecting/disconnecting an external microphone or device to/from the INPUT1 or INPUT2 jack, be sure to set the INPUT1 (LINE/ MIC/MIC+48V) or INPUT2 (LINE/MIC/MIC+48V) switch to a position other than “MIC+48V.” Plugging/unplugging the cable into/from the external microphone or device while the switch is set to “MIC+48V” may cause loud noise or a malfunction of the device.
  • While recording is in progress, operating and handling noises from the camera or lens may be recorded. Touching this unit while recording is in progress will cause noise to be included in the recording.
  • While recording is in progress, do not change the INPUT1 or INPUT2 switch settings.
  •  If the microphone of this unit is in proximity to a speaker, acoustic feedback may occur. In this case, move the unit away from the speaker to allow the maximum distance between the microphone and the speaker, or lower the speaker volume.
  • If dust or water droplets are present on the surface of the microphone, successful recording may not be possible. Be sure to clean the microphone surface before using this unit.
  • Turn off the camera before attaching/removing this unit.
  • When this unit is connected to the camera and the HANDLE AUDIO switch is set to ON, the internal microphone of the camera cannot record audio input.
  • When attaching this unit to the camera, fasten the two handleattachment screws securely. Using this unit without fastening the handle-attachment screws may damage the Multi Interface Shoe terminal or cause the unit to fall off.

Attaching this unit to the camera

By attaching this unit, up to four audio devices can be connected to the camera simultaneously.

SONY-XLR-H1-XLR-Handle-Unit-fig-4

  1. Set the power switch of the camera to off.
  2. Remove the shoe cap from the camera and the handle shoe cap from this unit.
  3. Slide this unit into the Multi Interface Shoe until it reaches the back of the shoe.
    Then, be sure to securely tighten the screws (a) on either side using a coin, etc.
    For more information, refer to the Help Guide provided for the camera.

Specifications

  • Dimensions (Approx.): 113.2 mm × 140.8 mm × 172 mm (4 1/2 in. × 5 5/8 in. × 6 7/8 in.) (W/H/D) (excluding the projecting parts)
  • Mass (Approx.): 305 g (10.8 oz)
  • Included items: XLR handle unit (1), Handle shoe cap (1) (attached to this unit), Set of printed documentation
    Design and specifications are subject to change without notice.
    “Multi Interface Shoe” is a trademark of Sony Group Corporation.

Documents / Resources

SONY XLR-H1 XLR Handle Unit [pdf] User Manual
XLR-H1 XLR Handle Unit, XLR-H1, XLR Handle Unit, Handle Unit

References

Leave a comment

Your email address will not be published. Required fields are marked *