ROADSAFE Toyota Hilux Series 7 and 8 2005 On Recovery Points Instruction Manual
ROADSAFE Toyota Hilux Series 7 and 8 2005 On Recovery Points

FITTING INSTRUCTIONS

Assembly Instruction

VEHICLE Toyota Hilux N70 & N80 2005 – Current
PRODUCT Recovery Point
PRODUCT CODE RPHILALL
NOTE As this Recovery Point is designed to fit a range of bull bar applications, the required hardware will vary accordingly.

DURING RECOVERY ALWAYS USE BOTH RECOVERY POINTS

THIS REDESIGNED RECOVERY POINT IS DESIGNED TO FIT ALL FACTORY N70 AND N80 TOYOTA HILUX’S, AS WELL AS A RANGE OF BULL BAR APPLICATIONS. EACH BULL BAR APPLICATION WILL BE SLIGHTLY DIFFERENT AND MAY REQUIRE THE MODIFICATION OF BRACKETS AND OTHER COMPONENTS.

  1. Remove bull-bar wing under trays and centre tray.
  2. Identify the location of the recovery point and which application will suit installation.
  3. Once the specific application for your vehicle has been confirmed, mark and remove the factory front tow hooks. Remember to rust protect and paint any bare metal surfaces. See figure 1.
    Assembly Instruction
  4. Fit RP-HILALL into position and loosely secure in place using a minimum of 2 x M12x 100mm bolts and crush tubes through the middle holes in the chassis rail. See figure 2.
    Assembly Instruction
  5. Loosely fit the 2 x M10 Bolts and Nylocs where the front plate of the recovery point meets the front of the chassis rail. See figure 3.
    Assembly Instruction
  6. Loosely fit the rear most M12 x 40mm bolt through the recovery point into the captive nut in the chassis rail. See figure 3.
    Assembly Instruction
  7. Tighten all bolts evenly and then to the recommended torque specs.

Bolt Torque Specs

8.8 10.9 12.9
M10 41-60Nm 59-85Nm 65-94Nm
M12 71-105Nm 102-150Nm 114-164Nm
M14 112-168Nm 161-240Nm 182-265Nm
M16 175-260Nm 250-371Nm 282-406Nm

DURING RECOVERY ALWAYS USE BOTH RECOVERY POINTS

THESE INSTRUCTIONS ARE FOR FITMENT OF RPHILALL TO A HILUX N70 FITTED WITH AN XROX BULL BAR

Hardware utilized for fitment to a Hilux N70 fitted with an Xrox Bull bar:

  • 4 x M12*1.25*100mm
  • 2 x M12*1.25*40mm
  • 4 x M10*1.25*40mm
  • 10 x M12 Washer
  • 6 x M10 Washer
  • 4 x M10 Custom Washer
  • 4 x M12*1.25 Nyloc
  • 4 x M10*1.25 Nyloc
  1. Remove bull-bar wing under trays and centre tray.
  2. Using angle grinder or similar, Mark and remove the factory front tow hooks. See figure 1.
    Assembly Instruction
  3. The following modifications to the bull bar bracket are required:
    a. Trim the lower section of the bulbar bracket approximately 30mm upwards to allow the recovery point to sit flush against the bull bar backet.
    b. The Two middle holes will need to be modified. The forward most hole will need to be opened to suit an M12 bolt.
    c. The rear most hole will need to be added, drilling from the inside, using the hole in the chassis rail as a guide, drill a hole through the bulbar bracket to suit an M12 bolt. See figure 2.
    Assembly Instruction
  4. The front bulbar bracket will also need to be drilled using the hole in the chassis rail end as a guide. See figure 3.
    Assembly Instruction
  5. Clean up any exposed metal and rust protect. See figure 4.
    Assembly Instruction
  6. Fit RPHILALL into position and loosely secure in place using 2 x M12 x 100mm bolts and crush tubes through the middle holes in the chassis rail. See figure 5.
    Assembly Instruction
  7. Loosely fit the 2 x M10 Bolts and Nylocs where the front plate of the recovery point meets the front of the chassis rail. See figure 6.
    Assembly Instruction
  8. Loosely fit the rear most M12 x 40mm bolt through the recovery point into the captive nut in the chassis rail. See figure 6.
  9. Tighten all bolts evenly and then to the recommended torque specs.

A division of Specialist Wholesalers Pty. Ltd. ABN 64 163 280 279 roadsafe.com.au

VIC PH: 03 8687 1700
QLD PH: 07 37377420
Email: sales@roadsafe.com.au

ROADSAFE Logo

Documents / Resources

ROADSAFE Toyota Hilux Series 7 and 8 2005 On Recovery Points [pdf] Instruction Manual
Toyota Hilux Series 7 and 8 2005 On Recovery Points, Toyota Hilux Series 7 and 8, 2005 On Recovery Points, Recovery Points, Points

References

Leave a comment

Your email address will not be published. Required fields are marked *