FOXFURY D10 Lighting System for DJI Avata

FOXFURY- D10-Lightin- System -or-DJI-Avata-product

Specifications

  • D10 Light:
    • DIMENSIONS: 1.07 x 0.77 x 1.4 in (27.3 x 19.5 x 36 mm)
    • WEIGHT: 0.42 oz (12 g)
  • DJI Avata Mount P/N 15-006:
    • DIMENSIONS: 1.20 x 1.14 x 0.74 in (30.6 x 29 x 18.7 mm)
    • WEIGHT: 0.16 oz (4.4 g)
  • D Series Flat Mounting Pad P/N 15-003:
    • DIMENSIONS: 1.14 x 1.06 x 0.2 in (29 x 27 x 5 mm)
    • WEIGHT: 0.06 oz (1.7 g)

Product Usage Instructions

Charging the Battery

Connect the provided Micro USB Cable to the Charging Port, and to a USB source. While charging, a green light will blink. Once charged, the green light will remain steady on. Charge time should be approximately 1 hour.

WARNING: Unplug the light once charged to avoid impacting battery life. If the battery is fully discharged due to non-use, please charge it fully.

Operational Modes

To operate the D10 Light:

  1. Press and hold the Power/Mode Switch for 3 seconds to turn the light ON.
  2. Press the Power/Mode Switch again to switch to STROBE mode.
  3. Press the Power/Mode Switch again to turn the light OFF.
MODE WHITE LUMENS BATTERY LIFE
ON 200 30 – 40 minutes
STROBE 200 60 – 80 minutes

Installation

Mounting D10 Light on DJI Avata

  1. Align the bottom of the D10 light with the mount snap lock location and snap the D10 unit in place.
  2. Spin and tug the mount to ensure it is properly attached.
  3. Take the mount with the light installed, and mount it onto the DJI Avata, confirming proper hooking and secure attachment before flight.

Alternate Installation with Third D10 Light and Flat Mounting Pad

  1. The third D10 Light and Flat Mounting Pad can be installed on the top of the drone or in an alternate location based on preference.
  2. Attach one half of the included 3M Dual Lock Reclosable Fastener to the desired location on the drone and the other half to the flat side of the mounting pad.
  3. Press firmly for good adhesion and trim if necessary.
  4. Align the bottom of the D10 with the snap lock location on the mount and snap the D10 light in place. Spin and tug to ensure proper attachment before flight.

FAQ

  • Q: How long does it take to charge the D10 Battery?
  • A: The charge time for the D10 Battery is approximately 1 hour.
  • Q: What is the battery life of the D10 Light in different modes?
  • A: The D10 Light has a battery life of 30-40 minutes in ON mode and 60-80 minutes in STROBE mode.
  • Q: What should I do if the battery is fully discharged due to non-use?
  • A: If the battery is fully discharged due to non-use, please charge it fully before use.

OVERVIEW

This D10 Lighting System consists of multiple mounts and D10 lights that are Made in the USA for the DJI Avata drone. The D10’s 30° LED beam pattern operates on continuous or strobe light modes. This rechargeable and splashproof light is durable and compact for a variety of uses where light is needed in a tight space. All 3 lights rotate 360° for optimum light placement.
IMPORTANT

Please fully charge the D10 before using it for the first time. Please read this manual before using your D10 Lighting System for DJI Avata as it relays beneficial operating and safety Information.

PHYSICAL CHARACTERISTICS

D10 Light

DIMENSIONS 1.07 x 0.77 x 1.4 in (27.3 x 19.5 x 36 mm)
WEIGHT 0.42 oz (12 g)

DJI Avata Mount P/N 15-006

DIMENSIONS 1.20 x 1.14 x 0.74 in (30.6 x 29 x 18.7 mm)
WEIGHT 0.16 oz (4.4 g)

D Series Flat Mounting Pad P/N 15-003

DIMENSIONS 1.14 x 1.06 x 0.2 in (29 x 27 x 5 mm)
WEIGHT 0.06 oz (1.7 g)

REFERENCE GUIDE

FOXFURY- D10-Lightin- System -or-DJI-Avata-fig-12

WHAT’S INCLUDED P/N 700-324

  • D10 White Light (3 ea)
  • DJI Avata Front Mount (2 ea)
  • Micro USB Cable (3 ea)
  • D Series Flat Mounting Pad (1 ea)
  • 3M Dual Lock Reclosable Fastener (2 ea)

REFERENCE GUIDE
FOXFURY- D10-Lightin- System -or-DJI-Avata-fig-2

WARNINGS

  • Please fully charge the D10 before using it for the first time.
  • Do not stare into the LEDs for long periods of time or from a close range (less than 2 ft / 0.6 m).
  • While using any FoxFury product, please operate at safe speeds.
  • It is the responsibility of drone/UAV users to follow the FAA and global laws and regulations and/or the laws and regulations applicable to the flight location.

BATTERY

CHARGING THE BATTERY

  • Connect the provided Micro USB Cable to the Charging Port, and to a USB source.
  • While charging, a green light will blink. Once charged, the green light will remain steady.
  • Charge time should be approximately 1 hour.

WARNING:
Unplug the light once charged to avoid impacting battery life. If the battery is fully discharged because the unit may have not been in use for many months, please charge it fully.

OPERATIONAL MODES

  • Press and hold the Power/Mode Switch for 3 seconds to turn light ON.
  • Press the Power/Mode Switch again to turn the light to STROBE.
  • Press the Power/Mode Switch again to turn light OFF.
MODE WHITE

LUMENS

BATTERY LIFE
ON 200 30 – 40 minutes
STROBE 200 60 – 80 minutes

INSTALLATION

  1. Align the bottom of the D10 light with the mount snap lock location and snap the D10 unit in place. Spin and tug the mount to make sure it is properly attachedFOXFURY- D10-Lightin- System -or-DJI-Avata-fig-3
  2. Take the mount with the light installed, and mount it onto the DJI Avata, as shown below (lights are removed for simplicity). Confirm the mount is hooked on properly and secured before flight. Repeat steps on the opposite side of teh drone.
  3. The included third D10 Light and Flat Mounting Pad can be installed on the top of the drone or in an alternate location based on the user’s preference or application. Attach one half of the included 3M Dual Lock Reclosable Fastener to the desired location on the drone and the other half to the flat side of the mounting pad. Press firmly for good adhesion and trim if necessary. Align the bottom of the D10 with the snap lock location on the mount and snap the D10 light in place. Spin them and tug to make sure they are properly attached before a flightFOXFURY- D10-Lightin- System -or-DJI-Avata-fig-5

NOTE: When recharging D10 lights, they can either be removed from the Saddle or remain installed.
NOTE: Before our accessories are made available, they are tested internally and verified externally by a minimum of 2 professional users. We have experienced multiple cases of UAS (drone) mechanical modifications from manufacturers within the same P/N and revision, and without providing warnings or product updates. If there is a fit problem, please contact our customer service department at https://www.foxfury.com/contact/

WARRANTY

WARRANTY AND OTHER INFORMATION

PRODUCT DURABILITY 

FOXFURY- D10-Lightin- System -or-DJI-Avata-fig-6

PRODUCT NAME & PART NUMBER: D10 Lighting System for DJI Avatav P/N: 700-324
CARE/CLEANING
Your FoxFury product is a professional tool. Regular maintenance and care of your light will maximize performance for you. As needed, clean your FoxFury product using a damp soft washcloth. Do not immerse.

ACCESSORIES

  • D Series Mount Set, P/N 850-730
  • D10 Infrared (IR), P/N 700-318

WARNINGS
FoxFury, LLC is not responsible for the incorrect use of any FoxFury Lighting product.

  • Lights are strong enough to cause damage to the human eye.
  • Do not stare into LEDs for long periods of time or from a close range (less than 2 ft / 0.6 m).
  • FoxFury, LLC is not responsible for any injury or damage caused during the use of this product.
  • Usage of this product must be supervised by an adult when it is being used by a minor.
  • Any FoxFury product should be operated at speeds safe enough to maneuver around surrounding obstacles.
  • Do not use under the influence of drugs or alcohol.

ONE YEAR WARRANTY
FoxFury, LLC (“FoxFury”) warrants this product to be free from defects in material for one year after purchase. LiPo batteries have a one-year pro-rated or 300 re-charge cycle pro-rated warranty, whichever the user reaches first.
This warranty is given only to the original end user of the accompanying product. If you purchased a product from someone other than an authorized FoxFury reseller/distributor or if the product was used, (including but not limited to demo models, show models or refurbished products by someone other than FoxFury) before your purchase, you are not the Original Purchaser and the product that you purchased is not covered by this warranty. This warranty is VOID if this Product has been altered or modified in any way (including but not limited to attempted warranty repair without authorization from FoxFury and/or alteration/removal of the serial number). To expedite warranty concerns, we encourage the end user to register their FoxFury Product at www.foxfury.com/pages/warranty-registration.

THIS IS THE ONLY WARRANTY, EXPRESSED OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. INCIDENTAL, CONSEQUENTIAL
OR SPECIAL DAMAGES ARE EXPRESSLY DISCLAIMED EXCEPT WHERE SUCH LIMITATION IS PROHIBITED BY LAW. You may have other specific legal rights which vary by jurisdiction. Go to www.foxfury.com/pages/warranty for a complete copy of the warranty. Retain your receipt for proof of purchase

CONTACT

All FoxFury products are designed in Oceanside, CA. All FoxFury products are manufactured with the highest quality USA and foreign parts. Products are assembled in either FoxFury’s controlled plant in Asia or the USA, under strict quality control.

CALIFORNIA PROPOSITION 65
This product can expose you to chemicals including Lead and DEHP, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.go

Documents / Resources

FOXFURY D10 Lighting System for DJI Avata [pdf] User Manual
D10 Lighting System for DJI Avata, D10, Lighting System for DJI Avata, System for DJI Avata, DJI Avata

References

Leave a comment

Your email address will not be published. Required fields are marked *