AEROMOTIVE-logo

AEROMOTIVE 14112 Acura Integra

AEROMOTIVE-14112-Acura-Integra-product

Product Information

AEROMOTIVE Part # 14112 ’94-’01 Acura Integra INSTALLATION INSTRUCTIONS
The AEROMOTIVE Part # 14112 is a fuel rail designed for installation on a ’94-’01 Acura Integra. It is intended to be installed on an unmodified OEM intake manifold of the identified application. Please note that proper fitment on aftermarket intake manifolds is not guaranteed, and the end user is responsible for verifying proper fitment and assumes all liability.

  • The fuel rails utilize o-ring sealed AN-08 style ports, which are NOT PIPE THREAD and do not require thread sealant. To use the enclosed fuel rails in your vehicle’s fuel system, you must install the necessary adapter fittings and o-rings, high-pressure fuel lines, and regulators to adapt your system to the configuration and ports of these fuel rails.
  • It is important to handle gasoline with caution during installation. Ensure you are working in a well-ventilated area with an approved fire extinguisher nearby. Extinguish all open flames, prohibit smoking, and eliminate all sources of ignition in the area of the vehicle before proceeding with the installation. Wear eye goggles and other safety apparel as needed to protect yourself from debris and sprayed gasoline.
  • Note that the fuel system is under pressure, and it is crucial not to open the fuel system until the pressure has been relieved. Refer to the appropriate vehicle service manual for the procedure and precautions for relieving the fuel system pressure.
  • Aeromotive system components are not legal for sale or use on emission controlled motor vehicles.

Specifications

  • Part Number: 14112
  • Application: ’94-’01 Acura Integra
  • Fuel Rail Type: O-ring sealed AN-08 style ports

Product Usage Instructions

Preparation

  1. Ensure the engine has cooled down.
  2. Disconnect the negative battery cable.
  3. Relieve fuel system pressure following the procedure in the appropriate vehicle service manual.
  4. Check for any dirt or debris around the fuel injectors and clean them using solvent parts cleaner or a clean shop towel.
  5. Disconnect the electrical connector at each injector, making note of the location of each.
  6. Disconnect both the supply and return fuel lines from the OEM fuel rails. Place clean shop towels around the open fuel lines to catch any gasoline that may drip out and to prevent dirt from entering the fuel lines.

Installation

  1. Install the necessary adapter fittings and o-rings onto the fuel rails.
  2. Connect the high-pressure fuel lines to the fuel rails.
  3. Install a regulator to adapt your system to the configuration and ports of the fuel rails.
  4. Verify proper fitment on the OEM intake manifold.

Note:
The above instructions are for a typical installation. For specific year and model installation instructions, please refer to your vehicle’s service manual.

FAQ

Q: Are the Aeromotive system components legal for use on emission controlled motor vehicles?
A: No, Aeromotive system components are not legal for sale or use on emission-controlled motor vehicles.

Safety Instruction

CAUTION: 

  • Installation of this product requires detailed knowledge of automotive systems and repair procedures. We recommend that this installation be carried out by a qualified automotive technician.
  • Installation of this product requires the handling of gasoline. Ensure you are working in a well-ventilated area with an approved fire extinguisher nearby. Extinguish all open flames, prohibit smoking and eliminate all sources of ignition in the area of the vehicle before proceeding with the installation.
  • When installing this product, wear eye goggles and other safety apparel as needed to protect yourself from debris and sprayed gasoline.

WARNING!
The fuel system is under pressure. Do not open the fuel system until the pressure has been relieved. Refer to the appropriate vehicle service manual for the procedure and precautions for relieving the fuel system pressure.

  • The enclosed Aeromotive fuel rails utilize o-ring sealed AN-08 style ports; these ports are NOT PIPE THREAD and utilize NO THREAD SEALANT. To use the enclosed fuel rails in your vehicle’s fuel system you must install the necessary adapter fittings and o-rings, high-pressure fuel lines and regulators to adapt your system to the configuration and ports of these fuel rails. Please call for a catalogue of the complete line of quality Aeromotive products.
  • The enclosed Aeromotive fuel rails are intended to be installed on an unmodified OEM intake manifold of the identified application. Aeromotive cannot guarantee the proper fitment on aftermarket intake manifolds and the end user is responsible for verifying proper fitment and assumes all liability.
  • When installing o-rings it is important to place a small amount of light oil on both the o-ring and the mating surface to ease installation and prevent damaging the o-ring.
  • The following installation instructions are for a typical installation, for specific year and model installation instructions please refer to your vehicle’s service manual.
  • Aeromotive system components are not legal for sale or use on emission-controlled motor vehicles.

Kit Contains

This kit contains the following parts:

  • 1ea 14112 Acura Integra Fuel Rail
  • 1ea 15113 OEM Fuel Supply Line Adapter

Installations

The following steps are typical of most installations:

  1. Once the engine has been allowed to cool, disconnect the negative battery cable and relieve fuel system pressure, referring to the appropriate vehicle service manual for the procedure for doing so.
  2. Check for any dirt or debris around the fuel injectors. If any is evident, wash it off with some solvent parts cleaner or wipe it off with a clean shop towel.
  3. Disconnect the electrical connector at each injector, making note of the location of each.
  4. Disconnect both the supply and return fuel lines from the OEM fuel rails. Place clean shop towels around the open fuel lines to catch any gasoline that may drip out and to prevent any dirt from entering the fuel lines. Failure to satisfy all safety considerations will result in fire, explosion, injury and/or loss of life to yourself and/or others.
  5. Label and disconnect any electrical wiring, vacuum lines and components that will interfere with the fuel rail removal and installation.
  6. Remove the 3 mounting bolts that attach the fuel rail to the intake.
  7. Place clean shop towels around the injectors to catch any gasoline that may be spilled during their removal. Remove the injectors from the manifold by gently pulling upward on the fuel rail/injector assembly. Keep all injectors connected to the fuel rails. If an injector does pull out of the fuel rail, it may spill a large amount of fuel. Failure to satisfy all safety considerations will result in fire, explosion, injury and/or loss of life to yourself and/or others.
  8. Carefully remove the fuel injectors from the OEM fuel rail.
  9. Remove the old o-rings from the fuel injectors, inspect the injectors for any dirt or debris and clean if needed. It is suggested that the old o-rings be replaced, contact your local parts store or dealer to purchase the correct replacement o-rings.
  10. Carefully install the new fuel injector o-rings on the injectors.
    • When installing o-rings it is important to place a small amount of light oil on both the o-ring and the mating surface to ease installation and prevent damaging the o-ring.
  11. Place a thin coat of light oil in the fuel rail fuel injector bores and in the lower intake manifold injector bores to help prevent cutting the o-rings during installation.
  12. Carefully place each of the four fuel injectors in the corresponding fuel injector bore of the Aeromotive fuel rail.
  13. Reinstall the phenolic bushing between each of the three mounting brackets on the fuel rail and the engine. After ensuring that the injectors are properly seated in the intake manifold injector bores, install the three provided mounting bolts, ensuring that the phenolic bushings are properly captured between the fuel rail bracket and the engine.
  14. Install and tighten the 3 provided fuel rail mounting bolts.
  15. With the Aeromotive fuel rail properly secured to the intake manifold, Move the fuel injector vertically downward until it bottoms out on the intake manifold, In this downward position, inspect the upper fuel injector o-ring (on the fuel rail side) and ensure it is fully covered by the fuel rail injector bore. If any of the o-ring is exposed, remove material from either the fuel rail bracket and/or intake manifold mounting boss to adjust the installation height until the o-ring is no longer exposed and reinstall the mounting bolts. In the situation where the fuel injector has no vertical travel, Shim the mounting brackets upward until the fuel injector fits freely. Do not pressurize the fuel rail until the proper fuel rail installation height is achieved.
  16. Install the appropriate union fittings and o-rings at each end of the fuel rail, we recommend Aeromotive p/n 15605 for AN-06 or Aeromotive 15607 for AN-08. On the timing cover end of the fuel rail, clearances are tight we recommend using use an AN-08 male o-ring boss hose end, Aeromotive p/n 15665. As an alternative using an Aeromotive fitting p/n 15605 AN-06 fitting in conjunction with an AN-06 90-degree hose end will clear. This hose end must be installed before bolting down the fuel rail to the engine.
  17. Using an after-market fuel pressure regulator (We recommend Aeromotive 13101, 13105, 13109 or 13129) and high-pressure fuel lines and fittings, plumb the remainder of the fuel systemAEROMOTIVE-14112-Acura-Integra-fig-1 Ensure that any spilled gasoline and any gasoline-soaked shop towels are cleaned up and removed from the vicinity of the vehicle!
  18. Reconnect the battery and turn the ignition to the ON position WITHOUT starting the car. After several seconds, check the fuel pressure. If there is no fuel pressure, turn the ignition key to the OFF position, wait one minute, return the ignition to the ON position, and recheck the fuel pressure. Repeat this ignition OFF and ON procedure until the fuel pressure gauge registers fuel pressure.
  19. With the fuel pressure gauge registering fuel system pressure, check for fuel leaks from and around all the fuel system components and all fuel lines and connections! If any fuel leaks are found, turn the ignition key to the OFF position, remove any spilled fuel and repair the leak before proceeding!
  20. Once the fuel pressure gauge registers fuel system pressure and there are no fuel leaks, start the engine and adjust the regulator to the desired fuel pressure.
  21. Once the desired fuel pressure is achieved, tighten the regulator adjustment jam nut and attach the vacuum line.
  22. Turn off the engine and allow it to cool.
  23. Test drive the car to ensure proper operation and re-check the fuel system for leaks. If any leaks are found, immediately shut off the engine and repair the leak(s)!

WARNING:
This product can expose you to chemicals, including chromium, which is known to the State of California to cause cancer birth defects or other reproductive harm. For more information, visit www.p65Warnings.ca.gov.

AEROMOTIVE, INC. LIMITED WARRANTY

  • This Aeromotive Product, with proof of purchase dated on or after January 1, 2003, is warranted to be free from defects in materials and workmanship for one year from the original date of purchase. No warranty claim will be valid without authentic, dated proof of purchase.
  • This warranty is to the original retail purchaser and none other and is available directly from Aeromotive and not through any point of distribution or purchase.
  • If a defect is suspected, the retail purchaser must contact Aeromotive directly to discuss the problem, and possible solutions and obtain a Return Goods Authorization (RGA), if deemed necessary by the company. Please call 913-647-7300 and dial option 3 for the technical service dept. All returns must be shipped freight pre-paid to the company and with a valid RGA before they will be processed.
  • Aeromotive will examine any product returned with the proper authorization to determine if the failure resulted from a defect or from abuse, improper installation, misapplication or alteration. Aeromotive will then, at its sole discretion, return, repair or replace the product.
  • If any Aeromotive product is determined defective, the buyer’s exclusive remedy is limited in value to the sale price of the good. In no event shall Aeromotive be liable for incidental or consequential damages.
  • Aeromotive expressly retains the right to make changes and improvements in any product it manufactures and sells at any time. These changes and improvements may be made without notice at any time and without any obligation to change the catalogues or printed materials.
  • Aeromotive expressly retains the right to discontinue at any time and without notice any Aeromotive product that it manufactures or sells.
  • This warranty is limited and expressly limits any implied warranty to one year from the date of the original retail purchase on all Aeromotive products.
  • No person, party or corporate entity other than Aeromotive shall have the right to: determine whether or not this Limited Warranty applies to any Aeromotive product, authorize any action whatsoever under the terms and conditions of this Limited Warranty, assume any obligation or liability of any nature whatsoever on behalf of Aeromotive under the terms and conditions of this Limited Warranty.
  • This Limited Warranty covers only the product itself and not the cost of installation or removal.
  • This Limited Warranty is instead of and expressly excludes all other warranties, expressed or implied. This Limited Warranty gives you specific legal rights, and you may also have other rights that vary from state to state.

Contact Information

Aeromotive, Inc.

  • 7805 Barton Street, Lenexa, KS 66214
  • Phone: (913) 647-7300
  • Fax: (913) 647-7207

Documents / Resources

AEROMOTIVE 14112 Acura Integra [pdf] Instruction Manual
14112 Acura Integra, 14112, Acura Integra, Integra

References

Leave a comment

Your email address will not be published. Required fields are marked *