AXC - logoE0001
2018-up Jeep Wrangler JL & JLU
(Will not fit Gladiator JT)

E0001 X-LINE Fender Flare Jeep Wrangler Unlimited

Warning IconWARNING: This product contains a chemical known to the State of California to cause Cancer and Reproductive Harm. For more information, go to www.P65Warnings.ca.gov.

PRIOR TO INSTALLATION
A) Install the flares according to these written instructions with the hardware provided.
WARNING: Failure to install according to these instructions will invalidate the warranty. This includes, but is not limited to, using alternative installation methods, hardware,  or materials. DO NOT USE: Loctite, Superglue, or similar products on the hardware or the flares. Install flares on cleaned vehicle surfaces.
B) Fit: Verify the fit of the flares to vehicle prior to installation (some filing, sanding, or cutting may be necessary to ensure proper fit).
C) Painting: (Optional) if paint is desired it must be done prior to installing flares on vehicle. Clean outer surface with a good grade degreaser. DO NOT USE LACQUER  THINNER OR ENAMEL REDUCER AS A DEGREASER. Wipe outer surface thoroughly with a tack rag prior to paint. Application of plastic adhesion promoter for  ABS plastic as per your paint system manufacturer’s recommendations is required. Paint flares using a high-quality enamel, or polyurethane automotive paint. If painting edge  trim (not recommended), use a flex additive.
D) Performance: Using larger tires may increase the area required to turn the vehicle.
Some tire/rim combinations may require lowering bump stops and or installing steering stops to prevent tire from contacting flare.
E) Exhaust System: Modifications may be necessary to maintain a minimum 4” clearance between flares and exhaust pipes. (Exhaust gases should not vent directly onto flares.)
F) Metal Protection: All exposed fasteners and bare metal should be treated with rust resistant paint BEFORE installing flares. Spray inner fender wells with undercoating  AFTER flare attachments have been completed.
G) Decals: Flares may interfere with existing decals on vehicle. If you wish, remove decals prior to installation of flares.
H) Care & Cleaning: Fender flares are built to last; any detergent you use to wash your vehicle is sufficient to clean the flare. Do not use any harsh abrasive detergents.

TOOLS FOR EASY INSTALLATION:

  • Safety Glasses
  • Gloves
  • 10mm Socket
  • T-30 Torx Bit
  • Ratchet
  • Phillips Screwdriver
  • Plastic Pry Tool
  • Awl
  • Cut-off wheel or Saw/Snips
  • Sanding Disc or Sandpaper (50-80 grit)

PLEASE READ: Dirt and debris can become lodged between the fender flares and the vehicle’s fenders, causing scratching and paint wear from vibration. Manufacturer is  not responsible for any damage, and the installation of our fender flares is done with the buyer’s understanding that this scratching and paint wear may occur.
LIMITED LIFETIME WARRANTY AGAINST ANY MANUFACTURING DEFECTS: To claim warranty you must provide Proof of Purchase.

INCLUDED IN HARDWARE KIT:AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - KIT

WARNING Installation of these flares may require aftermarket wheel well liners or modification of factory wheel well liners (not outlined in this instruction).

SECTION 1: FRONT FACTORY FLARE REMOVAL

AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 1

Put on safety glasses and gloves. On front factory flare, use an awl to pop 8 factory retainers in center of each retainer to disengage.

AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 2

Factory retainer locations.

AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 3

Using a plastic pry tool, remove each retainer popped in Step 1. Discard.

AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 4

To remove wheel well liner, first use a pry tool to remove 6 factory retainers from liner and discard (liner is shown removed from wheel well for viewing ease).

AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 5

Using a 10mm socket, remove 3 factory bolts. Retain.
Remove and discard wheel well liner.
NOTE: Liner will need to be trimmed and reinstalled, or replaced with an aftermarket liner. AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 6

Remove 2 bolts from Light Housing. Retain.

AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 7

Disconnect Light Wire Harness by pushing the red tab out to unlock. Push the release tab and pull the harness out. AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 8

To remove lower bracket, use pliers behind bracket and sheet metal to disengage 2 white factory retainers. Discard. AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 9

Disengage 9 white factory brackets that are holding factory flare onto vehicle, spaced along wheel well. All but one bracket are accessible by pliers. If you wish to preserve the paint finish (which will be covered by flare), use a plastic pry tool to help remove retainers. AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 10

Pull factory flare from vehicle. Pry any white retainers from sheet metal and discard – holes must be clear for installation. Retain factory flare to remove light housing in next  steps.

SECTION 2: LIGHT HOUSING REMOVAL AND MODIFICATION

AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 11

Turn flare on its back on a work surface. Using a Phillips screwdriver, remove 1 factory fastener from light housing as shown. Retain ALL factory fasteners – most will be reused. AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 12

Using a T-30 Torx bit, remove 4 factory fasteners as shown.

AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 13

Lift housing flap up to remove 4 more fasteners underneath it as shown, using a T-30 Torx bit. AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 14

Remove wire harness from light housing routing using your hands or pliers. Do not cut the electrical tape; simply pry from contact points gently. Disconnect light bulb connector(s). Remove light housing from factory flare. AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 15

Slide side marker light from housing.

AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 16

Light is taped to OE flare. Gently pry housing from flare to disengage tape. If tape sticks to lens surface you may remove it, but it will not show in the final assembly. AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 17

Reinstall side marker light by installing the short factory coarse-thread screw removed earlier back into light housing as shown. AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 18

Using a cutoff wheel or saw, cut four plastic tabs on light housing as shown.

AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 19

Areas to cut. The goal is to remove these tabs parallel with contours of light housing as cleanly as possible.

AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 20

Using a sanding disc or sandpaper, sand down any remaining tab vestiges. Tab vestiges must be as flush as possible for proper installation.

SECTION 3: LIGHT HOUSING REASSEMBLY

AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 21

Install a supplied “U” Clip over hole in bottom bracket of modified light housing, centering hole in clip over hole in bracket. AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 22

Reconnect harness and/or light bulbs if you removed them.
The wire harness will need to be routed in the formed-in groove in the housing and ultimately to the connector in the engine compartment when installing new flares. AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 23

Assemble modified light housing with supplied Front Bracket. Start 3 factory screws through supplied Front Bracket and into modified light housing, but do not tighten.
NOTE: Two Coarse-thread screws are included in case of loss. AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 24

Using an awl, make sure “U” clip installed previously is still centered over hole in bracket. AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 25

Start a supplied Truss screw into clip – only engage a few threads to catch screw. Screws will not be tightened until after the light housing is installed in new flare.

SECTION 4: FRONT FLARE INSTALLATION

AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 26

Slide 2 supplied “U” Clips onto Front Flare Inner Bracket as shown.

AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 27

Holding flare on fender, install 2 supplied Plastic Retainers through holes in flare in locations shown and into holes in fender. Push each retainer in to engage. The remainder  of Plastic Retainers will be installed in later steps. AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 28

Holding flare on fender, install 2 supplied Plastic Retainers through holes at bottom rear of flare, under flare corner bracket feature, and into holes in fender.
Push each retainer in to engage. AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 29

Fit assembled light housing bracket into inside of flare as shown. AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 30

Using a 10mm socket, start 2 factory bolts through housing and into red sheet metal brackets on vehicle. Do not tighten. AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 31

Bolt locations. NOTE: It is helpful to use an awl to line holes up prior to starting bolts.

AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 32

Using a Phillips screwdriver, start 2 supplied Truss screws through clip holes in bracket and into Flare InnerPiece. Do not tighten. AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 33

Check fit of light inside light pocket and adjust screws incrementally as needed to ensure even fit – tighten screws installed in Step 23 before screw installed in Step 25.
Slowly tighten all screws in light housing and bracket. AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 34

Route wire harness from light housing over the first of the metal fender brackets and toward channel molded into Flare. AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 35

Tuck wire harness up into channel in flare and route into engine compartment (connector is located near washer fluid reservoir). Connect wire harness to connector. AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 36

Install remaining 7 plastic fasteners.

AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 37

Plastic Fastener locations. AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 38

Complete Front Flare installation.

SECTION 5: REAR FACTORY FLARE REMOVAL

On rear factory flare, use an awl to pop 8 factory retainers center of each retainer to disengage. AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 40

Factory retainer locations.

AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 41

Using a plastic pry tool, pry each plastic retainer from vehicle and discard. AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 42

To remove wheel well liner, first use a pry tool to remove 4 factory retainers from outer edge of wheel well liner and discard (liner is shown removed from wheel well for viewing ease).

AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 43

Using a pry tool, remove 4 factory retainers from liner area behind wheel and discard. Remove and discard wheel well liner.
NOTE: Liner can be discarded, trimmed and reinstalled, or replaced with an aftermarket liner. AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 44

Use pliers and pry tool to disengage 12 white factory retainers. Unlike the front, these retainers are not accessible from behind, so force will be needed. Discard.AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 45

Pull factory flare from vehicle. Pry any white retainers from sheet metal and discard – holes must be clear for installation. Discard factory flare.

SECTION 6: REAR FLARE INSTALLATION

AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 46

Holding flare on fender, install 11 supplied Plastic Retainers through holes in flare and into holes in fender. Push each retainer to engage. NOTE: 1 Plastic Fastener will be  placed in the factory hole at the lower front without engaging the flare. AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 47

Plastic Fastener locations. NOTE: Fastener in lower front goes directly into sheet metal.

AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited - Step 48

Complete Rear Flare installation.

Documents / Resources

AXC E0001 X-LINE Fender Flare Jeep Wrangler Unlimited [pdf] Installation Guide
E0001 X-LINE Fender Flare Jeep Wrangler Unlimited, E0001 X-LINE, Fender Flare Jeep Wrangler Unlimited, Jeep Wrangler Unlimited, Wrangler Unlimited

References

Leave a comment

Your email address will not be published. Required fields are marked *