MBS K10+ KIAU0059 Kooltherm K10 Plus Soffit Board Kingspan AU

MBS K10+ KIAU0059 Kooltherm K10 Plus Soffit Board Kingspan AU Installati

IMPORTANT INFORMATION

Kingspan Kooltherm K10 Plus Insulation
INSTALLATION GUIDE

Your Ceiling Specialist
Every material. One source.

PARTNERING WITH THE WORLD’S LEADING CEILING MANUFACTURERS

Great design is in the detail, and the details are our speciality. We offer the broadest range of premium products from a single source. Our proprietary systems provide the platform for your unique design, giving you complete freedom and customisation to create truly stunning projects.

MBS Architectural can supply any of the products featured in this brochure, and be your one point of contact throughout the project lifecycle – from design conception to installation on site.

Reach out to get your hands on product samples, or discuss your project in more detail-03 9580 7800 / hello@mbsarchitectural.com.au

INSULATED FIBRE CEMENT SHEET FOR CONCRETE SOFFITS 

  • Super high performance rigid thermoset phenolic insulation
  • Non–combustible building board outer face
  • Fibre-free, closed cell insulation core
  • Available in a range of selected lining materials
  • Group 1 NCC fire classification
  • Resistant to the passage of water vapour
  • No CFC or HCFC used in manufacture
  • Has zero ODP and low GWP
  • NCC and AS/NZS 4859.1:2018 compliant
  • Made in Australia

Typical Constructions and Total R-values

Concrete Soffit Floor / Roof Installation
Total R–values for various thicknesses of Kingspan Kooltherm® K10 PLUS Soffit Board Applicable for NCC Volume One, Class 2 to 9 buildings & NCC Volume Two, Class 1 & 10a buildings, & NCC Volume One, Class 2 sole-occupancy unit or a Class 4 part of a building
Product Thickness* Heat flow in Heat flow out
Roof application, no ceiling (150 mm concrete)
31 mm RT1.4 RT1.4
36 mm RT1.6 RT1.6
46 mm RT2.0 RT2.1
56 mm RT2.6 RT2.7
66 mm RT3.1 RT3.2
76 mm RT3.5 RT3.7
86 mm RT4.0 RT4.2
96 mm RT4.5 RT4.7

Roof Installation

Thermal Performance

NCC 2019 prescribes different methods to determine Total R-value Calculations for Volume 1 and Volume 2.

*Product thickness = nominal insulation thickness + 6 mm Fibre Cement sheet

Assumptions
The R-values shown are Total R-values for the building element as required by the Energy Provisions of the National Construction Code, calculated in accordance with AS/NZS 4859.2 2018 & NZS 4214. Kingspan Kooltherm® products are manufactured, tested and packaged in conformance with AS/NZS 4859.1:2018

Total R–values for various thicknesses of Kingspan Kooltherm® K10 PLUS Soffit Board Applicable for NCC Volume One, Class 2 to 9 buildings & NCC Volume Two, Class 1 & 10a buildings, & NCC Volume One, Class 2 sole-occupancy unit or a Class 4 part of a building
Product Thickness* Heat flow in Heat flow out
Unenclosed sub-floor application (150 mm concrete)
31 mm RT1.4 RT1.4
36 mm RT1.5 RT1.7
46 mm RT2.0 RT2.1
56 mm RT2.6 RT2.8
66 mm RT3.0 RT3.3
76 mm RT3.5 RT3.7
86 mm RT4.0 RT4.0
96 mm RT4.4 RT4.7
Enclosed sub-floor application (150 mm concrete)
31 mm RT2.0 RT2.1
36 mm RT2.2 RT2.4
46 mm RT2.6 RT2.8
56 mm RT3.2 RT3.5
66 mm RT3.7 RT4.0
76 mm RT4.1 RT4.4
86 mm RT4.6 RT4.9
96 mm RT5.1 RT5.4

Product Details

Product Description

Kingspan Kooltherm® K10 PLUS Soffit Board is a super high performance, fibre-free rigid thermoset, closed cell phenolic insulation core, sandwiched between a front facing fibre cement sheet and a reverse tissue based facing autohesively bonded to the insulation core during manufacture.

Kingspan Kooltherm® K10 PLUS Soffit Board is manufactured without the use of CFCs/HCFCs and has zero Ozone Depletion Potential (ODP) and low Global Warming Potential (GWP).

A selection of alternative lining boards to create customised finishes and facings is available. Please contact us for more information.

 Product Data
Insulant 0.021 W/m.K at 23oC
(Insulant thickness ≥ 45 mm)0.023 W/m.K at 23oC(Insulant thickness 25 – 44 mm)
Declared Thermal Conductivity
Fibre Cement 0.23 W/m.K at 23oC (Fibre Cement thickness 6 mm)
Product Dimensions 2400 mm x 1200 mm(2.88 m2)
Other dimensions available upon enquiry. Minimum order quantities apply.
Nominal Product Thickness (inc. FC Sheet) 31, 36, 46, 56, 66, 76, 86, 96 mm
Nominal Fibre Cement Sheet Thickness 6 mm
Product R-value

Figure 2 Super high performance Kingspan Kooltherm® PLUS Plus Soffit Board

Nominal Product Thickness
(inc. Fibre Cement Sheet)
Declared Product R-value
31 mm R1.10
36 mm R1.40
46 mm R1.75
56 mm R2.35
66 mm R2.85
76 mm R3.35
86 mm R3.80
96 mm R4.30

Product Details

Specification Guide

Kingspan Kooltherm® K10 PLUS Soffit Board
The soffit insulation shall be Kingspan Kooltherm® K10 PLUS Soffit Board ___ mm thick, with a tested smoke obscuration of not more than 100 m2 /kg, comprising a CFC/HCFC-free and zero Ozone Depletion Potential (ODP) rigid thermoset phenolic insulation core with a front facing non-combustible fibre cement sheet and a reverse tissue based facing, manufactured under a management system certified to ISO 9001:2015, ISO 14001:2015, OHSAS 18001:2007 and ISO 50001:2011 by Kingspan Insulation Pty Ltd And shall be installed in accordance with the instructions issued by them.
A Project Specific Warranty provided by Kingspan Insulation must be submitted.

Standards and Approvals

Kingspan Kooltherm® K10 PLUS Soffit Board is manufactured to the highest standards and certified under the following management systems:

Standard Management System
ISO 9001:2015 Quality Management
ISO 14001:2015 Environmental Management
OHSAS 18001:2007 Health and Safety Management
ISO 50001:2011 Energy Management
Product Testing
Characteristic Standard Result
Compressive Stress (Insulant) AS 2498.3 Typically exceeds 100 kPa at 10% compression
Water Vapour Resistance BS EN 12086:1997 / I.S. EN 12086:1998 > 35 MN.s/g

For the purpose of calculation of condensation risk, the resistivity of the fibre cement sheet component of the product should be taken as 250 MN·s/g·m.

Fire Performance

* Applies only to the Kingspan Kooltherm® K10 insulation board used in the manufacture of this composite insulated fibre cement product.
** Applies to compliant fibre cement facing.
*** Testing to AS 1530.4 for the Kingspan Kooltherm® K10 performed in accordance with NCC BCA C3.15 Openings for service penetrations using a 120 mm concrete soffit.

Test Test Method Result
Ignitability, Flame spread, Heat release,Smoke release AS 1530.3 Spread of Flame Index: 0

Smoke Development ≤ 3*

NCC Group Number in accordance with AS 5637.1 AS/NZS 3837 / Amdt 1 Group 1**
Average Specific Extinction Area AS/NZS 3837 ≤ 100 m2/kg**
Fire-resistance test of elements of construction AS 1530.4*** -/240/240 (HDPE pipe)
Durability

If correctly applied, Kingspan Kooltherm® products can be expected to have a long life of service.
Their durability depends on the supporting structure and the conditions of its use.
Kingspan Kooltherm® products are warranted for a period of 10 years for both residential and commercial installations.*
* Subject to the terms of the complete Kingspan Kooltherm® warranty document which is available upon request or downloadable from www.kingspaninsulation.com.au.

Environmental Data
Aspect Characteristic
Recyclability Non-contaminated insulation site waste is recyclable, but there are currently no facilities in Australia to process returned material
Re-usability Re-usable if removed with care (long term of service expected)
Water Use No water used in Kingspan Insulation’s manufacturing process
Blowing Agent Global

Warming Potential (GWP)

Manufactured with a blowing agent that has low GWP
Blowing Agent Ozone Depletion Potential (ODP) Manufactured with a CFC/HCFC-free blowing agent that has zero ODP
Packaging Contains 0% recycled product Polythene wrap and EPS skids 100% recyclable

Installation Instructions

Fibre Cement Sheet

Kingspan Kooltherm® K10 PLUS must be installed in accordance with AS 2908.2:1992 Cellulose Cement Products. Installation must be in accordance with AS 3999 Bulk Thermal Insulation Installation and AS 3000 Electrical Installations (Wiring Rules).

Fixing Directly to Concrete Soffits

Kingspan Kooltherm® K10 PLUS Soffit Board can be fully restrained to a concrete soffit by the use of minimum 11 No. appropriate mechanical insulation fasteners with a minimum head diameter of 25 mm

  1. The fasteners should be evenly distributed over the whole area
    of the board and designed to provide suitable restraint for the
    project requirements. Consultation with the chosen fastener
    supplier is recommended.
  2.  Board joints can be either staggered (see Figure 5) or squared
    (see Figure 6). 4 No. fasteners along each length – no less than
    50 mm – no more than 150 mm from edge of board, 3 No.
    fasteners along the middle (offset from edge positions as per
    diagram Figure 3).
  3. Where the board may be subject to external wind pressure,
    the requirement for additional fixings should be assessed in
    accordance with appropriate Australian wind load standards.
  4. Consideration should be given to the material the fixing is
    made from and should be deemed appropriate for application,
    exposure and fire rating by the fixing manufacturer.
    Installation Instructions

Why 11 fixings?
Best practice determines that any rigid board insulation, not just Kingspan Kooltherm® K10 PLUS Soffit Board, should be fixed with 11 mechanical fixings for very good reasons:

  • There will always be differential expansion and contraction between any rigid insulation material and adjacent building products due to varying moisture content and temperature.
  • In any concrete forming, there will be an uneven surface throughout the slab.
  • Where concrete formwork is joined it is normal to have ridges of up to 3 mm which make the concrete surface uneven.
  • An insulation board held horizontally may bow like any other sheet material under its own weight. Using 11 fixings ensures that the insulation board has a strong and permanent fix under the concrete soffit and that it is not compromised by any of the above issues. It also provides a proven robust fire safe solution.

These best practice recommendations are a result of over 30 years of Kingspan Insulation experience in soffit applications.
Figure 4 Side elevation – Concrete Soffit with Kingspan Kooltherm® K10 PLUS Soffit Board
Installation Instructions

Figure 5 Board joints staggered
Figure 6 Board joints squared
Installation Instructions

Installation Instructions (continued)

Fixing to Timber Battens / Furring Channels
  1.  Alternatively, a treated softwood batten/furring channel lay-out may be adopted if there is an uneven surface or mechanical services present and direct fixing is not possible.
  2. 50 mm x 25 mm battens/furring channels should be placed at 600 mm centres to coincide with the edges/centres of the boards.
  3.  The battens/furring channels should be fixed to the soffit by the use of a suitable fixing method e.g. shot-fire may be considered.
  4.  Kingspan Kooltherm® K10 PLUS Soffit Board should then be fixed to the treated timber battens/furring channels using suitable screw fixings. These should be placed at maximum 300 mm in rows not greater than 600 mm apart.
  5.  Locate fasteners not less than 12mm from sheet edges and 50mm from sheet corners.
  6.  Where the board may be subject to external wind pressure, the requirement for additional fixings may need to be assessed in accordance with appropriate wind load standards.

For advice on ancillary materials, such as fixings and tapes please contact our Technical Services Department.

Installation around Fire Collars
  1. Fitting Kingspan Kooltherm® K10 PLUS Soffit Board tight to the fire collar is recommended to reduce the effects of thermal bridging through the slab.
  2. Do not cover the exposed face of embedded cast in fire collars.

Figure 7 Penetration example – Kingspan Kooltherm® K10 PLUS Soffit Board installed tight around the fire collar and HDPE service pipe.
Installation Instructions

General

Cutting

Cutting fibre cement sheets should be carried out by using a suitable fibre cement blade. For alternative lining materials ensure an appropriate blade is used. Ensure accurate trimming to achieve close-butting joints and continuity of insulation.

Taping

Taping is not required for bonded boards. In the absence of other protection, exposed board edges should be protected by silver Kingspan Insulation Tape with a minimum 48 mm wide overlap onto the board face (see Figure 8) or alternatively use a proprietary metal c-section.

However, to reduce vapour transmission consideration should be given to sealing the joints

Figure 8 Protection of exposed insulation edges of Kingspan Kooltherm® K10 PLUS Soffit Board
Installation Instructions

Packaging

According to quantity, the boards are supplied in packs, labelled and shrink-wrapped in polythene.

Handling and Storage

Storage

The packaging of Kingspan Kooltherm® should not be considered adequate for long term outdoor protection. Ideally boards should be stored inside a building. If, however, outdoor storage cannot be avoided then the boards should be stacked clear of the ground and covered with an opaque polythene sheet or weatherproof tarpaulin. Boards that have been allowed to get wet should not be used.

Resistance to Solvents

The insulation core is resistant to short–term contact with petrol and with most dilute acids, alkalis and mineral oils. However, it is recommended that any spills be cleaned off fully before the boards are installed. Ensure that safe methods of cleaning are used, as recommended by suppliers of the spilt liquid. The insulation core is not resistant to some solvent-based adhesive systems, particularly those containing methyl ethyl ketone. Adhesives containing such solvents should not be used in association with this product. Damaged boards or boards that have been in contact with harsh solvents or acids should not be used.

OH & S

Kingspan Insulation products are chemically inert and safe to use. A Product Safety Information sheet is available from Kingspan Insulation Pty Ltd.

QR-Code
Scan to see installation video “Fixing Directly to Concrete Soffits

Customer Support

Every material. One source.
Reach out to our team for support, samples and advice.
03 9580 7800
hello@mbsarchitectural.com.au
VIC | 7 Haymer Court, Braeside 3195
QLD | 13 Pease Court, Bethania 4205
@MBSarchitectural

Zo Logo
Insulation Logo
Kooltherm Logo
Logos
Mbs Logo

Documents / Resources

MBS K10+ KIAU0059 Kooltherm K10 Plus Soffit Board Kingspan AU [pdf] Installation Guide
K10 KIAU0059 Kooltherm K10 Plus Soffit Board Kingspan AU, K10 KIAU0059, Kooltherm K10 Plus Soffit Board Kingspan AU, K10 Plus Soffit Board Kingspan AU, Plus Soffit Board Kingspan AU, Soffit Board Kingspan AU, Board Kingspan AU, Kingspan AU

References

Leave a comment

Your email address will not be published. Required fields are marked *