TORO 44552 Engine Shuts Down After 3 Minutes Pro Force Debris Blower LOGO

TORO 44552 Engine Shuts Down After 3 Minutes Pro Force Debris Blower

TORO 44552 Engine Shuts Down After 3 Minutes Pro Force Debris Blower PRODUCTAbout Product

  • Bulletin Type
    • Information Only
  • Status
    • Final Release
  • Affected Units
    Model Number(s) Serial Number(s)
    44552 315000001 and Up
    44552TE 400000000 and Up
    44553 315000001 and Up
    44554 315000001 and Up
  • Distribution
    • For Distributor and Customer Bulletin only
  • Situation
    • Important Information
      Toro has received reports that the engine is shutting down without operator input after a few minutes; after the engine shuts down, it can be restarted without issue but only runs for another few minutes before it shuts down again. This situation can be caused when the Toro TEC controller loses, or never establishes, an oil pressure signal from the Kohler® engine oil pressure switch.
      After 3 minutes of running, the TEC controller starts checking the oil pressure signal from the engine; if the oil pressure signal is lost or never found, the TEC will remove power from the fuel solenoid, causing the engine to shutdown as a precaution to prevent engine damage. This may be due to a faulty engine oil pressure switch.
  • Corrective Action
    • Fix as Fail
      Use an ohm meter and the wiring schematic to test the oil pressure switch. When the engine is not running, the oil pressure switch should show an open circuit to ground; when the engine is running, the oil pressure switch should have continuity to ground (assuming there is good oil pressure).
      If the above test indicates a missing sensor signal, the oil pressure switch may need to be replaced, or the engine may have low oil pressure.
      Inspect for possible low oil pressure as directed in the Kohler® Engine Service Manual; if the oil pressure is found to be good, the wiring from the oil switch to the TEC is found to be good, and the oil pressure switch is not producing a proper path to ground, it is likely that the oil pressure switch needs to be replaced; replace it with a new Kohler engine oil pressure switch with new rubber boot to help deter water entry into the switch.
  • Safety Awareness
    • Follow reasonable and customary safety precautions.
  • Parts
    • Currently available
      Kohler Part No. Part Description Quantity
      24 755 425-S Kit* Kohler engine oil pressure switch kit* 1

      *Must be obtained from your local Kohler dealer

  • Special Tools Required
    • Tool Description
      Kohler Command CH730 Service Manual
  • References
    • Find the latest operator’s manuals, service manuals, schematics, parts catalogs, and customer bulletins at www.Toro.com.
      Resource Search Term
      Operator’s Manual Model and serial number for the machine.
      Engine Owner’s Manual N/A

Service Instructions

Testing and Replacing the Engine Oil Pressure Switch

  1. Move the machine to a level surface.
  2. Shut off the machine, remove the key, wait for all moving parts to stop, and wait for all parts to cool before servicing the machine.
  3. Inspect for possible low oil pressure as directed in the Kohler Engine Service Manual; follow the diagnostic steps as directed in the Kohler Service Manual.
    Important: Detailed information on engine troubleshooting, testing, disassembly, and assembly is given in the Kohler Command Pro CH740 Service Manual; contact your local Kohler Engine Dealer or visit http://kohlerengines.com to obtain a copy of the engine Service Manual.
  4. If the diagnostic steps point to an issue with the engine oil pressure switch, replace it with a new Kohler engine oil pressure switch with a new rubber boot to help deter water entry into the switch.
    Refer to the Kohler Command CH730 Service Manual for more detailed instructions.
    • Disconnect the negative battery cable from the battery terminal. Position the disconnected negative cable away from the negative battery terminal.
    • Disconnect the wire lead extending from the oil pressure switch and remove the switch from the engine.
      Note: Note how this wire is connected for later installation.
    • Install the new engine oil pressure switch to the location shown in Figure 1; apply and torque the switch to 40 in-lbs (4.5 N·m).
    • Connect the wire lead on the new oil pressure switch to the engine as it was connected in step B.

TORO 44552 Engine Shuts Down After 3 Minutes Pro Force Debris Blower FIG 1Engine oil pressure switch location

 

Documents / Resources

TORO 44552 Engine Shuts Down After 3 Minutes Pro Force Debris Blower [pdf] User Manual
44552, Engine Shuts Down After 3 Minutes Pro Force Debris Blower, 44552 Engine Shuts Down After 3 Minutes Pro Force Debris Blower, After 3 Minutes Pro Force Debris Blower, Pro Force Debris Blower, Force Debris Blower, Debris Blower, Blower

References

Leave a comment

Your email address will not be published. Required fields are marked *