CentoLight Spire LS2000 High Power Laser Beam Moving Head User Manual

CentoLight Spire LS2000 High Power Laser Beam Moving Head User Manual

Before you Begin

Thank you for purchasing Spire LS2000. Enjoy your new equipment and make sure to read this manual carefully before operation! This user manual is made to provide both an overview of controls, as well as information on how to use them.

What is included

Package include:

• 1x Spire LS2000 Moving Head
• 1x Power Cord (EU plug – PowerCon)
• 1x DMX Cable (3-Pin XLR Male to Female)
• 2x Fast-Lock Omega Clamps
• This User manual

ATTENTION: Packaging bag is not a toy! Keep out of reach of children!!! Keep in a safe place the original packaging material for future use.

Unpacking Instructions

Carefully unpack the product immediately and check the content to make sure all the parts are in the package and are in good condition.

If the box or the contents (the product and included accessories) appear damaged from shipping, or show signs of mishandling, notify the carrier or dealer/seller immediately. In addition, keep the box and contents for inspection.

If the fixture must be returned to the manufacturer, it is important that it is returned in the original manufacturer box and packing. Please do not take any action without first contacting your dealer or getting in touch with our after-sales support service (visit www.centolight.com for details).

Accessories

CENTOLIGHT can supply a wide range of quality accessories that you can use with your Spire Series equipment, like Cables, Splitters, DMX controllers, Consumables, and a wide range of other fixtures.

All products in our catalogue has been long tested with this device, so we recommend you to use Genuine CENTOLIGHT Accessories and Parts.

Ask your CENTOLIGHT dealer or check out our website www.centolight.com for any accessories you could need to ensure best performance of the product.

Disclaimer

The information and specifications contained in this User Manual are subject to change without notice. CENTOLIGHT assumes no responsibility or liability for any errors or omissions and reserves the right to revise or to create this manual at any time.

Copyright© 2023 CENTOLIGHT. All rights reserved.

SAFETY INSTRUCTIONS

• Read these instructions
• Keep these instructions
• Heed all warning
• Follow all instructions

	The symbol is used to indicate that some hazardous live termi- nals are involved within this apparatus, even under the normal operating conditions, which may be sufficient to constitute the risk of electric shock or death.
	The symbol is used to describe important installation or config- uration problems. Not following advice and information on how to avoid such problems may lead to product malfunction.
	This symbol indicates a protective grounding terminal.
WARNING:	Describes precautions that should be observed to prevent the danger of injury or death to the operator.
	To protect the environment, please try to recycle packing materi- al and exhausted consumables as much as possible.
	This symbol indicates that the fixture is intended to indoor use only. Keep the machine dry and do not expose to rain and mois- ture.
	Don’t throw this product away just as general trash, please deal with the product follow the abandon electronic product regula- tion in your country.

MOUNTING AND RIGGING

Pay attention to safety! Please respectively consider the EN 60598-2-17 and the national standard during the installation. Only authorized technicians can carry out the installation.

Rigging

• The installation of the fixture has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming demolition. The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net. This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails.
• When rigging, de-rigging or servicing the fixture staying in the area below the installation place, on bridges, under high working places and other endangered areas is forbidden. The operator has to make sure that the safety measure and the machine’s technical installation is approved by an expert before taking into operation for the first time and after changes before taking into operation anther time. He has also to make sure that an expert approves safety measure and the machine’s technical installation once a years.

IMPORTANT: Overhead rigging requires extensive experience, including (but not limited to) calculating working load limits, installation material being used, and periodic safety inspection of all installation material and the projector. If you lack these qualifications, do not attempt the installation yourself, but instead use a professional structural rigger. Improper installation can result in bodily injury or property loss.

• If the fixture shall be lowered from the ceiling or high joists, professional trussing systems have to be used. The fixture must never be fixed swinging freely in the room.

CAUTION: Use appropriate clamps to rig the fixture on the truss. Make sure that the device is fixed properly! Ensure that the structure (truss) to which you are attaching the fixtures is secure.

Water / Moisture

• The product is for indoor use. In order to prevent risk of fire or electric shock, do not expose to rain or moisture.
• The unit can not be used near water; for example near a bathtub, a kitchen sink, a swimming pool, etc.

Heat

• Do not use in a confined space. Always install the product in a location with adequate ventilation, at least 20in (50 cm) from adjacent surfaces. Be sure that no ventilation slots on the product’s housing are blocked.
• The apparatus should be located away from heat sources such as radiators, stoves or other appliances that produce heat.

Don not use it when maximum ambient temperature is higher than 45°C. Work temperature ranges from -25°C to 45°C (-13°F to 113°F).

Servicing

• Do not implement any servicing other than those means described in the manual. Refer all servicing to qualified service personnel only. The internal components of the equipment must be purchased from the manufacturer. Only use accessories/attachments or parts recommended by the manufacturer.

INTRODUCTION

This Laser Beam moving head of the Spire Series is an ulta compact, lightweight and stylish moving head with a White Laser source, integrated with a unique high resolution optical system.

The fixture features a 0.7° beam angle which helps to provide an ultra long-throw beam effect that is close to a parallel beam, and it is designed with a range of effects: 19 static gobos, 17 dichroic colors, 6-color wheel, 2 prism wheels, frost, focus, etc. The Spire LS2000 provides a 360° continuous, fast and smooth Pan/Tilt movement with variable speed which delivers an even more vivid visual effect to the show. It supports DMX and RDM (Remote Device Management) control. The fixture’s exterior housing is beautifully balanced and based on a modern design philosophy, with a supremely harmonious interior structure for remarkable control. The body of the Spire LS2000 has more than just a striking look, the 2 fastening omega clamps, available for vertical and horizontal plug-in, make installations fast and easy.

Its fast and quiet operation makes the Spire LS2000 a perfect option for indoor application like small concerts, conference halls, DJ shows, clubs and bars.

Features

• 1x White Laser Lamp
• 30x 0.2W 3-In-1 RGB LEDs
• CRI:≥70
• Flicker-free operation for broadcast TV and Film
• Lamp Life Span: 30.000 H
• Silent operation – No fans
• Set of high resolution and precise optics with 0.7° Beam angle
• Smoot and precise linear focus
• 360° continuous, fast and smooth Pan/Tilt movement
• Fast, quiet, smooth and precise motors
• 1x Color wheel with 17 dichroic colors + white
• Variable direction rainbow effect with adjustable speed
• 6-color wheel with variable direction and adjustable speed
• 1 Neon ring effect with different built-in macro effects (variable speed control)
• 1x Static gobo wheel with 19 gobos plus open
• 2 Prism wheel design:
  Prism 1: 8-facet circular prism with variable speed and direction Prism 2: 3 different prisms, 6-facet linear prism / 16-facet circular prism / 8+16-facet circular prism with variable speed and direction
• Prism overlay (prism morphing)
• 0-25Hz shutter/strobe effect with variable speed
• 0-100% smooth linear dimming
• 25CH / 28CH DMX channels USITT DMX512
• DMX512/Master-Slave/Auto/Sound modes
• DMX recorder and edit function integrated
• RDM available (Remote Device Management)
• Shielded input signal protection for stable signal without interference
• RJ45 etherCON IN/OUT (Optional with Art-Net)
• 3-pin and 5-pin XLR DMX connectors IN/OUT
• Electronic supply with active PFC
• PowerCON IN/OUT with fuse

Spire LS2000 Sizes

PRODUCT OVERVIEW

Front Panel

1. LCD Display: Shows all functions, operating mode, menus and system information.
2. MENU: Press to open main menu. Also works as “go back” and “exit” button.
3. OK: Press to access selected menus and confirm values and functions.
4. UP: It scrolls individual functions up when in menus/submenus, and increases values/settings shown on the display.
5. RIGHT: Enters menus and sub-menus.
6. DOWN: It scrolls individual functions down when in menus/submenus, and decreases values/settings shown on the display.
7. PAN ON/OFF Button: Press to disable the 360° continuous pan rotation function.
8. DMX Output: Female 3-pin XLR DMX output for sending the DMX signal.
9. DMX Input: Male 3-pin XLR DMX input for connection to a DMX control device.
10. Power IN Socket: Input socket for fixture’s power supply. Plug the power-cord into an AC socket properly configured for your model.
11. Fuse Holder: In case of fuse burn, make sure the unit is turned off and disconnected from the AC outlet before replacing

Rear Panel

1. DMX Output: Female 5-pin XLR DMX output for sending the DMX signal.
2. DMX Input: Male 5-pin XLR DMX input for connection to a DMX control device.
3. Power OUT Socket: Output socket for power supply to additional Centolight fixtures ( cascade connection up to a max. of 24 fixtures).

About Power Connection

• Always make sure that the voltage of the outlet you are connecting the product to is within the range stated in paragraph ”11 – Specifications” on page 19 or front panel of the product (AC100V-240V 50/60Hz).
• Make sure the power cord is not crimped or damaged. Never connect this product to a dimmer pack or rheostat.
• Never disconnect the product from power cord by pulling or tugging on the cord.
• To avoid electric shock, all fixtures must be connected to circuits with a suitable ground and automatic switch.
• Wire correspondence is as follows:

Cable (EU)	B	International
Brown	Live	L
Blue	Neutral	N
Yellow/Green	Earth

Earth must be connected! Always pay attention to safety! Before taking into operation for the first time, the installation has to be approved by an expert.

About Dmx Connection

When use a DMX controller, please make sure that there is no interference sources (e.g. intercom, high frequency radio waves and radiation source).

DMX machines are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which the machines are connected is not important and has no effect on how a controller communicates to each of them. Use an order that provides for the easiest and most direct cabling.

Connect machines using shielded 2-conductor twisted pair cable with 3-pin XLR male to female connectors. The shield connection is pin 1, while pin 2 is Data Negative (S-), and pin 3 is Data positive (S+).

CAUTION: Wires must not come into contact with each other; otherwise the fixtures will not work at all, or will not work properly

DMX Terminator

DMX is a resilient communication protocol, however errors still occasionally occur. In order to prevent electrical noise from disturbing and corrupting the DMX control signals, a good habit is to connect DMX output of last fixture in the chain to a DMX terminator, especially over long signal cable runs.

The DMX terminator is simply an XLR connector with a 120Ω (ohm), 1/4 Watt resistor connected across Signal (-) and Signal (+), respectively, pins 2 and 3, which is then plugged into the outputsocket on last projector in the chain. The connections are illustrated below.

Complimentary signal cable can transmit signals to 20 unit fixtures at most. Signal amplifier is a must to connect more fixtures.

Pin vs 5-Pin DMX cables

DMX connection protocols used by controllers and fixtures manufacturers are not standardized around the world. However, two are the most common standards:
5-Pin XLR and 3-Pin XLR system. If you wish to connect this fixture to a 5-Pin XLR input fixture, you need to use an adapter-cable or make it by yourself. Below you can see the wiring correspondence between 3-Pin and 5-Pin plug and socket standards:

MENU OPERATION

Thanks to the LCD display, it’s very easy to set up and change operating mode. By pressing the MENU button, and the RIGHT button when in submenus (point 2 and 5 on”5.1. Front Panel” on page 9), the display will cycle through 7 different menus and 31 submenus. Press the OK button (3) to access selected menus, press UP (4), DOWN (6) or RIGHT (5) to navigate in the menus and change functions and values, then press OK (3) to confirm.

To exit menus and go back without making any changes, use the MENU button (2).

The main functions are shown in the chart below:

Fixture ResetMotor Reset DisplayLanguage

MAIN MENU	Second Menu	Third Menu	Fourth Menu
DMX Address	000-512
Fixture	DMX Mode	STD/EXT
	Run Mode	DMX/Host/Sound
	Pan Invert	Close/Open
	Tilt Invert	Close/Open
	No DMX Signal	Clear/Hold
	Sound Control	1 – 99
Manual	Pan	000-255
	Pan Fine	000-255
	Tilt	000-255
	Tilt Fine	000-255
Information	Time	Current Time	—H
		Total Time	—H
	Sensor	AllSensorsAreOk
	Temperature	HeadTemp	—C
	SoftwareVersion	Panel	V-.–
		Motor	V-.–
Factory	Password	000-255
	Pan	000-255
	Tilt	000-255
	Color	000-255
	Gobo	000-255
	Prism1	000-255
	Prism1Rot	000-255
	Prism2	000-255
	Prism2Rot	000-255
	Fog	000-255
	Focus	000-255
	Cance/Run
	Factory	Cance/Run
	CH/EN
	DisplayFlip	Normal/Reverse
	DisplayMode	60s/Show

DMX Address
DMX Address setting allows you to set the DMX channel of the machine between 1 and 512.

Fixture

• DMX Mode: choose between the available DMX channel modes: 25CH (STD) and 28CH (EXT).
• Run Mode: choose the fixture’s operating modes between DMX, Host (master) or Sound Controlled mode.
• Pan Invert / Tilt Invert: choose “Open” to invert the rotation of the Pan and/or Tilt. Choose “Close” to keep it as default.
• No DMX Signal: choose “Clear” to stop the fixture when the DMX signal gets interrupted. The lights of the fixture go out and the fixture stops moving. Choose “Hold” to let the fixture continue to operate the same function as before the DMX signal was interrupted.
• Sound Control: choose the sensitivity of the sound input between 1 and 99.

Manual
In this section is possible to manually set the position of Pan/Pan fine and Tilt/Tilt fine functions.

Information
This section provides information about Total and Current hours of use, Status of all sensors inside the lamp, Internal temperature, and version of the Software used.

Factory
Reserved menu for the settings of all internal functions of the fixture. If necessary, contact customer assistance.

Fixture Reset
Control menu for reset functions. Select “Run” to start reset of motors, or to reset all parameters to factory settings.

Display
In this menu is possible to select the display language, Chinese (CH) or English (EN), reverse the display if necessary, and decide wether to turn the display off after 60 seconds (60s), or to leave it always on (Show).

DMX CHANNEL CHART

There are two modes to get DMX512 signal for this fixture; one is 25CH, and the other is 28CH. To see how to choose channel mode, please refer to point ”2) Fixture” on page 14.

25 Ch Mode

Channel	Function	Value	Description
1CH	Pan	0-255	Pan Movement 540°
2CH	Pan Fine	0-255	Fine tuning of Pan movement
3CH	Tilt	0-255	Tilt Movement 270°
4CH	Tilt Fine	0-255	Fine tuning of Tilt movement
5CH	P/T Speed	0-255	Adjusts Pan/Tilt speed
6CH	Continuous Pan	0-255	Continuous 360° Pan rotation
7CH	Continuous Tilt	0-255	Continuous 360° Tilt rotation
8CH	Dimmer	0-255	Dimmer function 0% – 100%
9CH	Strobe	0-3	No function
		4-103	Regular strobe, from slow to fast
		104-107	Open/White
		108-207	Pulse strobe, from slow to fast
		208-212	Open/White
		213-225	Random slow strobe
		226-238	Random medium-speed strobe
		239-251	Random fast strobe
		252-255	Open/White
10CH	Color	0-127	Manual rotation
		128-190	Clockwise rotation, from fast to slow
		191-192	Stop
		193-255	Anti-clockwise rotation, from slow to fast
11CH	Gobo Wheel	0-127	Manual rotation
		128-190	Clockwise rotation, from fast to slow
		191-192	Stop
		193-255	Anti-clockwise rotation, from slow to fast
12CH	Prism 1	0-127	Closed
		128-255	Open
13CH	Prism 1 Rotation	0-127	Manual rotation
		128-190	Clockwise rotation, from fast to slow
		191-192	Stop
		193-255	Anti-clockwise rotation, from slow to fast
14CH	Prism 2	0-63	Closed
		64-127	8-facet prism
		128-191	16-facet prism
		192-255	Rearranger
15CH	Prism 2 Rotation	0-127	Manual rotation
		128-190	Clockwise rotation, from fast to slow
		191-192	Stop
		193-255	Anti-clockwise rotation, from slow to fast
16CH	Fog	0-99	Closed
		100-199	Colorful
		200-255	Atomize
17CH	Focus	0-255	From near to far
18CH	Reset	0-25	No function
		26-255	Reset (starts after 5 seconds)
19CH	Led Strip Dim- mer	0-255	Led strip dimmer, 0% – 100%
20CH	Led Strip Strobe	0-255	Led strip strobe effect
21CH	Led Strip Red	0-255	Red color of Led strip
22CH	Led Strip Green	0-255	Green color of Led strip
23CH	Led Strip Blue	0-255	Blue color of Led strip
24CH	Led Strip Effect	0-255	Led strip effect
25CH	Led Strip Effect Speed	0-255	Led strip effect speed

Color and gobo wheels

17 dichroic colors + white

6 colors

Static gobos

Troubleshoot Ting

Phenomenon                                           Solution
Fixture cannot start to work	Check if the power fuse is burned out
Fixture starts normally, but not re- sponding to the DMX controller	Check if the DMX start address is correct Check if the XLR signal cable is damaged
Dark light, brightness decreased	Check whether the internal and external optical system is clean
Beam is seriously distorted	Check whether the lens is broken Clean the dust or oil on lens

MAINTENANCE

When the lens have fracture and other damage, they should be replaced in time. When the fixture does not start, please check if the fuse is burned out. The Spire LS2000 is installed with an overheating protection device. When it is overheated, the

overheating protection device will automatically cut off power.

In order to maintain the smooth rotation and movement of the mechanical parts, it is suggested to add grease every two months. Please use good quality grease.

In order to ensure the fixture works well, it should be cleaned once every 30 days. To optimize the output light efficiency, it is recommended to periodically clean internal and external optical lens, reflector and color filters. Do not use any chemical solvents. Clean the fixture according to usage and the surrounding environment. Clean with a soft cloth and cleaning products for glass.

SPECIFICATIONS

Light Sources	1x White Laser lamp, 30x 0.2W 3-in1 RGB LEDs
Color Temperature	6000K
Beam Angle	0.7°
CRI	≥70
Lamp average lifespan	30.000 hrs
Flicker-free	Yes
Display System	LCD display with selectable language (Chinese or English), revers- ible
Cooling System	No fans, noise-free cooling system
Pan	360° continuous / 540° 8-16 bit low noise
Tilt	360° continuous / 270°8-16 bit low noise
Control Mode	DMX512/Master-slave/Auto/Sound
Color Wheels	1 color wheel with 17 dichroic colors+white, rainbow effect and vari- able direction and speed; 1 6-colors wheel with variable direction and speed
Static Gobo Wheel	1 static gobo wheel with 19 gobos+white
Prism Wheels	Prism 1: 8-facet circular prism with variable speed and direction Prism2: 6-facet linear prism/16-facet circular prism/8+16-facet circu- lar prism with variable speed and direction
Neon Effect	1 Neon ring effect with different built-in macro effects with variable speed
Dimmer/Strobe	0%-100% Dimmer, 0-25Hz shutter/strobe with variable speed
DMX control	25CH / 28CH modes
Voltage	100-240V,50-60Hz
Power Consumption	90W
Working Temperature	-25°C to 45°C
IP Rating	IP20
Dimensions (WxDxH)	268 x 207 x 423.7 mm (10.55 x 8.15 x 16.68 in)
Weight	9.7 kg – 21.38 lbs.
Package Size (WxDxH)	400 x 310 x 530 mm (15.75 x 12.20 x 20.87 in)
Package Weight	12.2 kg – 26.90 lbs.

Note: Our products are subject to a process of continual further development. Therefore modifications to the technical features remain subject to change without further notice.

WARRANTY AND SERVICE / WARNING

All CEN TO LIGHT products feature a limited two-year warranty. This two-year warranty starts from the date of purchase, as shown on your purchase receipt. The following cases/components are not covered by this warranty: 

• Any accessories supplied with the product
• Improper use
• Fault due to wear and tear
• Any modification of the product effected by the user or a third party

CENTOLIGHT shall satisfy the warranty obligations by remedying any material or manufacturing faults free of charge at CENTOLIGHT’s discretion either by repairing or exchanging individual parts or the entire appliance. Any defective parts removed from a product during the course of a warranty claim shall become the property of CENTOLIGHT.

While under warranty, defective products may be returned to your local CENTOLIGHT dealer together with the original proof of purchase. To avoid any damages in transit, please use the original packaging if available. Alternatively, you can send the product to CENTOLIGHT SERVICE CENTER – Via Enzo Ferrari, 10 – 62017 Porto Recanati – Italy. In order to send a product to service center, you need an RMA number. Shipping charges have to be covered by the owner of the product.

For further information please visit www.centolight.com

WARNING EU AND EEA (NORWAY, ICELAND AND LIECHTENSTEIN

PLEASEREADCAREFULLY – This symbol indicates that this product is not to be disposed of with your household waste, according to the WEEE Directive (2012/19/EU) and your national law.
This product should be handed over to a designated collection point, e.g., on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (WEEE).

Improper handling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, waste authority, approved WEEE scheme or your household waste disposal service.

www.centolight.com

Documents / Resources

CentoLight Spire LS2000 High Power Laser Beam Moving Head [pdf] User Manual Spire LS2000, Spire LS2000 High Power Laser Beam Moving Head, High Power Laser Beam Moving Head, Laser Beam Moving Head, Beam Moving Head, Moving Head

References

• GHT Joint Venture
• Welcome - CentoLight
• User Manual