Danfoss-logo

Hydraulic hose ET9000-45-110 Hydraulic Hose Saw

Danfoss-Hydraulic-hose-ET9000-45-110-Hydraulic-Hose-Saw-product-image

ET9000-45-110 Hydraulic Hose Saw

The ET9000-45-110 Hydraulic Hose Saw is a breakthrough technology that utilizes a toothed blade to cut with the backs of each tooth. This design ensures that the blade does not take a kerf, and the saw bends the hose into the blade, spreading the cut edges to prevent burning and smoking.

Product Features

  • Utilizes a toothed blade for precise cuts
  • Bends the hose into the blade for clean cuts
  • Reduces friction, heating, and debris
  • Rugged and dependable tool

Product Usage Instructions

Before starting the machine, read all instructions and follow all safety guidelines. Do not remove safety guards, and unplug the machine prior to servicing. Proper hand protection and eye protection should be worn at all times when working with sharp cutting tools and high RPM cutting blades.

Operating Procedure

  1. Set pin placement for the size of hose you are cutting using the Pin Placement Guide on the right.
  2. Start the saw and allow the motor to come up to full speed. Cutting before full speed can cause very high amperage draw and shorten the life of the motor.
  3. Pull the saw head down over the hose with steady and even pressure. Let the blade do the job by cutting the hose and not ripping it. This becomes more important as the hose size becomes larger. If you notice a large amount of smoke and sparking, you may be forcing the hose too fast or the blade may be excessively
    dull.
  4. After the hose is cut, be careful as the blade spins down to a stop. A coasting blade is still dangerous!
  5. Examine the hose. Look at the squareness and how clean the cut is. A good cut goes a long way toward making a strong hose assembly.

The Pin Placement Guide only recommends potential optimal pin placement, but variables such as hose condition (new or used), hose
brand (standard or premium), hose reinforcement (braided or spiral), and hose cover type can impact optimal positioning. As an operator, you will learn the best pin placement for the hose you are cutting. Remember that the cut hose should be square and clean.

The ET9000-45-110 Hydraulic Hose Saw is a rugged and dependable tool that, when used and maintained properly, can be in daily service for years and still be in good working order.

CAUTION
Use extreme caution. Please read all instructions before starting machine. Follow all safety guidelines, do not remove safety guards. Unplug machine prior to servicing.

GLOVES
Proper hand protection should be worn at all times when working with sharp cutting tools.

SAFETY EYE WEAR
Proper eye protection should be worn at all times when working with high RPM cutting blades.

Introduction

The Danfoss hydraulic hose cutting system is break-through technology using a toothed blade, cutting with the backs of each tooth, so the blade does not take a kerf. The saw bends the hose into the blade spreading the cut edges to avoid burning and smoking.Danfoss-Hydraulic-hose-ET9000-45-110-Hydraulic-Hose-Saw-01

Old Method
The normal sawing method of lowering an abrasive saw blade onto the hose causes the hose to compress and deform. As the blade cuts the compressed hose expands against the blade causing friction, heating and burning and much of the debris from the kerf of the blade is deposited into your hose.

New Improved Method
With Danfoss hydraulic hose saws the hose is positioned across two pins (A) The saw head (B) is brought down over the hose. The bend motion causes the hose to stretch at the point of contact with the blade, allowing it to separate as it is cuts. This separation allows the hose to pass clear of the saw blade with LESS friction, LESS heating and LESS DEBRIS!

Danfoss-Hydraulic-hose-ET9000-45-110-Hydraulic-Hose-Saw-03 Danfoss-Hydraulic-hose-ET9000-45-110-Hydraulic-Hose-Saw-04

Operation

This saw is a rugged and dependable tool when used and maintained properly. Many of these saws have been in daily service for years and are still in good working order. As with any tool, good operating procedure is important for tool life and operator safety.

Operating Procedure

  1. Set pin placement for the size hose you are cutting using the Pin Placement Guide* on the right:
  2. Start the saw and let the motor come up to full speed. Cutting before full speed can cause very high amperage draw and shorten the life of the motor.
  3. Pull the saw head down over the hose with steady and even pressure. Let the blade do the job by cutting the hose and not ripping it. This becomes more important as the hose size becomes larger. If you notice a large amount of smoke and sparking, you may be forcing the hose too fast or the blade may be excessively dull.
    After the hose is cut, be careful as the blade s pins down to a stop. A coasting blade is still dangerous!
  4. Examine the hose. Look at the squareness and how clean the cut is. A good cut goes a long way toward making a strong hose assembly.

Danfoss-Hydraulic-hose-ET9000-45-110-Hydraulic-Hose-Saw-05*This guide only recommends the potential optimal pin placement, but variables, such as hose condi-tion (new or used), hose brand (standard or pre-mium), hose reinforcement (braided or spiral), and hose cover type can impact optimal positioning. As an operator you will learn the best pin placement for the hose you are cutting. Remember that the cut hose should be square and clean.

Changing the Blade

  1. Disconnect the saw from the power source.
  2. Remove the (3) knurled screws from the cover.
  3. Remove the cover.
    Danfoss-Hydraulic-hose-ET9000-45-110-Hydraulic-Hose-Saw-06
  4. Press the arbor lock opposite side of the grinder head
    (see image 1). While pressing the arbor lock, use the provided wrench to remove the collar.
  5. Remove the old blade and replace with a fresh one. Be sure the blade direction is correct. blades have a directional arrow on them. The saw turns counter clockwise when viewed from the motor shaft end.
  6. Tighten the collar with the tool provided, while pressing the arbor lock button. It should be snug but do not over tighten it as it stresses the motor assembly and is unnecessary.
  7. Replace the cover being sure to put the blade guard behind it. Tighten all the nuts firmly but do not over tighten.

Danfoss-Hydraulic-hose-ET9000-45-110-Hydraulic-Hose-Saw-07 Danfoss-Hydraulic-hose-ET9000-45-110-Hydraulic-Hose-Saw-08

Maintenance

Examine the blade periodically (blade cover in place) for chipping and cracking. Occasionally pull the blade cover off and perform a closer inspection of the blade paying attention to any cracks that may have occurred. If cracks are observed, the blade should be thrown away as it could break while spinning. Cracks are very rare as these blades are high quality steel and are tempered to the correct hardness for this application. With the cover off, clean the hose dust that has accumulated inside.
Keep the area around the saw uncluttered.

Benefits

  1. Cleaner cuts
  2. Safer cuts
  3. Less smoke
MODEL MOTOR BLADE CUTTING CAPACITY
ET9000-45-110 Makita 9557 PB Grinder 4.5” X 062 X 7/8” Arbor 3/4” ID x 2 Wire Hydraulic Hose

Hose Cutting Blades
Blades are manufactured in:
M-2, D-2, M-35, & High Speed Steels.

Danfoss ET9000C-45-MS Micro-Slotted Blade

Danfoss-Hydraulic-hose-ET9000-45-110-Hydraulic-Hose-Saw-09

About Danfoss Power Solutions FC

Danfoss hoses, fittings, and tooling provide the ultimate fluid conveyance solutions for a variety of equipment and applications around the world. We proudly engineer to support a sustainable future for tomorrow.
To learn more please visit: http://www.danfoss.com/en/about-danfoss/our-businesses/power-solutions

Danfoss Power Solutions
14615 Lone Oak Road
Eden Prairie, MN 55344, USA
Phone: 952-937-9800

Danfoss Power Solutions (US) Company
2800 East 13th Street
Ames, IA 50010, USA
Phone: +1 515-239-6000

Danfoss Power Solutions GmbH & Co.OHG
Krokamp 35
D-2439 Neumünster, Germany
Phone: +49 4321 871 0

Danfoss Power Solutions ApS
Nordborgveg 81
DK-6430 Nordborg, Denmark
Phone: +45 7488 2222

Danfoss Power Solutions Trade (Shanghai) Co. Ltd.
Building #22, No 1000 Jin Hai Rd
Jin Qiao, Pudong New District
Shanghai, China 201206
Phone: +86 21 3418 5200w

Danfoss can accept no responsibility for possible errors in catalogs, brochures, and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on order provided that such alterations can be made without subsequent changes being necessary in specifications already agreed. All trademarks in this material are the property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.

Documents / Resources

Danfoss Hydraulic hose ET9000-45-110 Hydraulic Hose Saw [pdf] Instruction Manual
ET9000-45-110 Hydraulic Hose Saw, ET9000-45-110, Hydraulic Hose Saw, Hose Saw, Saw

References

Leave a comment

Your email address will not be published. Required fields are marked *