TORO 147-8824 Jack Mount Kit Titan Riding Mower
Product Information
Specifications
- Product: Jack Mount Kit
- Model No.: 147-8824
- Form No.: 3465-980 Rev A
FAQ
- Q: Can I use any jack with the jack mount?
- A: Use only a manufacturer-approved jack rated at 907 kg (2,000 lb) or higher lift capacity with the jack mount.
Safety
Safety and Instructional Decals
Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing.
- Warning—read the Operator’s Manual.
- Crushing hazard—engage the parking brake, shut off the engine, and remove the key; support the machine using jackstands.
Installation
Determine the left and right sides of the machine from the normal operating position.
Preparing the Machine
Gas Models Only
- Park the machine on a level surface.
- Disengage the blade-control switch.
- Move the motion-control levers outward to the PARK position.
- Shut off the machine and remove the key.
- Wait for all moving parts to stop.
Electric Models Only
- Park the machine on a level surface.
- Disengage the blade-control switch.
- Move the motion-control levers outward to the NEUTRAL position.
- Engage the parking brake.
- Shut off the machine and remove the key.
- Wait for all moving parts to stop.
Installing the Jack Mount
- Secure the jack mount to the frame on the left of the machine using the backing plate, 2 hex-head bolts, and 2 locknuts (Figure 1).
- Note: For ease of access, secure the inner set of fasteners first before securing the outer set of fasteners.
- Torque the bolts to 19 to 25 N∙m (175 to 225 in-lb).
Operation
Using the Jack Mount
WARNING
The machine could fall onto someone and cause serious injury or death.
- Read and understand the Operator’s Manual before performing maintenance.
- Always shut off the engine, engage the parking brake, and remove the key before performing maintenance on the machine.
- Do not keep the machine raised on the jack for extended periods of time.
- Always use a jack on a level surface.
- Ensure that the jack is secured properly to the jack mount using a jack pin.
- Do not rely solely on the jack for support. Use adequate jack stands or equivalent support.
- Do not mount or dismount the mower while the jack is raised.
- Before each use, ensure that the jack and jack mount work properly and that there are no signs of damage.
Note: Use only a manufacturer-approved jack rated at 907 kg (2,000 lb) or higher lift capacity with the jack mount.
- Park the machine on a level surface, disengage the blade-control switch, and move the motion-control levers outward to the PARK position.
- Note: For electric models, move the motion-control levers outward to the NEUTRAL position and engage the parking brake.
- Shut off the machine, remove the key, and wait for all moving parts to stop before leaving the operating position.
- Attach the jack to the jack mount with a jack pin (Figure 2).
- Use the jack to raise the machine to the desired height.
- WARNING: Raising the machine could cause a fuel leak.
- Check for any fuel leaks before performing maintenance.
- If you see a fuel leak, immediately lower the machine and do not attempt to start the engine. Avoid creating a source of ignition until the fuel vapors have dissipated.
- WARNING: Raising the machine could cause a fuel leak.
- Support the machine with jack stands; refer to the machine Operator’s Manual for jack stand placement.
- . When finished, use the jack to lower the machine, then remove the jack.
- Note: Do not operate the machine with the jack attached.
© 2023—The Toro® Company
- 8111 Lyndale Avenue South Bloomington, MN 55420
- Register at www.Toro.com.
All Rights Reserved
Documents / Resources
 |
TORO 147-8824 Jack Mount Kit Titan Riding Mower [pdf] Instruction Manual 147-8824 Jack Mount Kit Titan Riding Mower, 147-8824, Jack Mount Kit Titan Riding Mower, Kit Titan Riding Mower, Titan Riding Mower, Riding Mower, Mower |
