SPISFL KT T45 HE FRI Cooker Hood
Product Information
Specifications
- Model: 991.0688.022/D000000008871
- Installation: Suspended
- Features: Easy-Clean motor core, LED lighting, metal mesh filters
- Speeds: Three speeds, intensive mode, ventilation mode
- Electrical Connection: 230V ~ earthed
- Lighting: LED 4 x 2 W
Product Usage Instructions
Installation
The cooker hood is intended for suspended installation. Follow the steps below:
- Use the provided fixing parts, screws, and components for installation.
- Connect the cooker hood to an earthed wall socket using the supplied cable and plug.
- Ensure the junction box or wall socket is accessible after installation.
- Refer to the installation components list for detailed instructions.
Assembly
- Mark the ceiling for installation and use the drill template for accurate positioning.
- Adjust the frame height according to the provided instructions.
- Protect the stove top with cardboard and place the cooker hood on it, ensuring it is flat.
- Adjust the length of the hose/duct for connection to the outlet air duct as per measurements.
FAQ
Q: What should I do if I encounter issues during installation?
A: If you face any difficulties during installation, refer to the detailed instructions provided in the manual or contact customer support for assistance.
Q: Can I replace the LED lighting on my cooker hood?
A: Yes, you can replace the LED lighting and LED driver following the guidelines provided in the user manual.
SAFETY INSTRUCTIONS
Please read this installation and user guide carefully before installing and using the product, paying special attention to the safety instructions.
Save these instructions for later use or for the party who may take over the product after you.
Disconnect the product from the power supply prior to cleaning or maintenance.
- Diversion of exhaust air must be carried out in accordance with instructions issued by the appropriate authority.
- Exhaust air may not be directed into flues that are used for fumes from items such as gas, wood or oil-burning stoves or fireplaces.
- The distance between the stove/gas hob and the product must be at least 65 cm. Adjust accordingly if the gas hobs manufacturer recommends a higher mounting height.
- For safety reasons, installation and replacement of cables or other types of connectors should only be carried out by a qualified professional.
- Flambéing underneath the product is not permitted.
If the product is to be used at the same time as products that use energy sources other than electricity, i.e., gas hobs, gas, wood or oil-burning stoves or fireplaces, etc, the room must have an adequate supply of air. - The product may be used by children from 8 years of age and persons with mental, sensory or physical impairment, or a lack of experience and knowledge, provided they are given information about how the product is to be used.
- Children should not be allowed to play with the product. Children must not undertake clea-ning or maintenance of the product unsupervised.
- ccessible parts of the product may become hot when food is being prepared.
- A fire is more likely to spread if the product is not cleaned as frequently as indicated.
INSTALLATION
The cooker hood is intended for suspended installation. The cooker hood is equipped with the Easy-Clean motor core, LED ligh-ting and metal mesh filters. The cooker hood has three speeds, an intensive mode as well as a ventilation mode. Installation, use, care, maintenance, etc., are described in these instructions
TECHNICAL INFORMATION
| Measurements | see Fig. 1 |
| Electrical connection | 230 V ~ earthed |
| Lighting | LED 4 x 2 W |
INSTALLATION
Fixing parts, screws for mounting, etc. are supplied with the cooker hood.
Electrical installation
The cooker hood is supplied with a cable and earthed plug for connection to an earthed wall socket.
When installing with an extended upper chimney section, take this into account when positioning sockets.
The junction box or wall socket must be accessible after installation is complete.
Installation Components
| A | 1 pc | Drill template |
| B | 1 pc | Frame |
| C | 4st | Screws 6×75 |
| D | 4st | Plugs Ø 10 x 60 |
| E | 4st | Screws 3.5×4.5 |
| F | 4st | Screws M6 x 8.8 |
| H | 1 pc | Screw 4.2 × 32 |
| J | 1 pc | Downdraught damper |
| K | 1 pc | Ventilation tape |
| L | 1 pc | Plug 5.5×35 |
Marking out the ceiling before installation
Attention!
For max. total height, the distance between the bottom of the cooker hood and the top of the chimney, see dimensions drawing Fig. 1. When installing with an extended upper chimney section or if the cooker hood will be fitted with a carbon filter kit, refer to the separate in-structions and measurements.
Protect the stove top with a piece of cardboard from the packaging, Fig. 3. Place the cooker hood on the stovetop. Make sure it is flat with the filter resting on the surface.
Attention!
To avoid the risk of head injury, do not allow any part of the product to protrude beyond the front of the stovetop.
Use a plumb line to mark the centre of the cooker hood on the ceiling. Locate the centre of the drill template supplied, A Fig. 3, against the marking in the ceiling so that the cooker hood ends up in the intended position.
Attention!
Turn the drill template so that the arrow points in the same direction as the front of the cooker hood.
- Mark out the template screw holes, A, and the connection to the outlet air duct. Drill holes in the centre of all the marked screw holes. Check which of the fastening alternatives apply and adapt the holes to fit screws/plugs or nuts, bolts and washers. If the supplied plugs are to be used, drill 6 mm holes. Insert wall plugs D into the holes. Check that the screws and plugs used are intended for the ceiling material. Cut out holes for connecting outlet air. Insert and tighten screws C into the pre-drilled holes for the keyhole attachments until they protrude a few mm, Fig. 5 .
- Check that the duct connection and electri-cal connection can still be made once the po-wer is installed in the ceiling.
Assembly
Adjusting frame height
Adjust frame height to ceiling height and cooker hood installation height. Measure the total ceiling height. Deduct cooker height, installation height and the chassis dimensions; see dimensions drawing Fig. 1 .
Frame measurement = Total ceiling height – cooker height – installation height – chassis height.
When adjusting the height of the frame, remove the screws, (8 pcs) Fig. 4A. Adjust the height of the frame and lock it by screwing in the screws again. It may be ne-cessary to move the screws to other hole positions.
Adjusting the length of the hose/duct for connection to the outlet air duct Fig. 4B
Measured the frame’s adjusted length. De-duct the connection box dimensions; see measurements drawing, Fig. 1.
Length of hose/duct = Frame measure-ment – 200 mm.
Installing chimney drums
Place the adjusted frame on the floor or on a table that is protected with a piece of cardboard from the packaging.
Slide the two drums onto the frame.
Fasten the outer drum to the frame using screws E, Fig. 5A.
Ceiling installation
Lift up the frame and slot the keyholes over the four screws D Fig. 5, installed in the ceiling/extension section.
Position the frame and tighten the screws. Lock in place using the fifth screw, H Fig. 5.
Attention!
Turn the frame so that the arrow is on the same side as the front of the cooker hood.
Frame installation
Remove the grease filter and motor unit Fig. 11 Fig. 12.
Adapt the length of the connection hose/duct according to frame height, the ceiling connection and the height of the connec-tion box (200 mm).
Tape the downdraught damper J into posi-tion using tape K, Fig. 6
If the connection is Ø 125 mm, a reducing coupling sleeve must be used. Secure the reducer to the downdraught damper with tape K.
Fit the connection hose/duct to the cooker hood’s outlet air collar.
Slide the hose/duct, the electrical connection cable and the cooker hood into the frame and fasten the chassis using screws F, Fig. 7A.
Reinstall the grease filter and motor unit.
Connect the hose/duct to the outlet air duct in the ceiling, Fig. 7B.
Connection to exhaust flue
Connect the cooker hood with a pipe or tubing Ø 160 mm.
Attention!
When using a connecting tubing, the tubing must be stretched and assembled to fit directly next to the connection, Fig. 8.
Installing the upper chimney drum
Pull the chimney drum into position and attach it using screws E, Fig. 9.
Removal of protective plastic
Cut the protective plastic in the joint between the upper and lower drum using a sharp knife or razor blade, Fig. 9. Remove the plastic from the chimney.
Remove all protective plastic from the filter and any other parts of the product.
INSTRUCTIONS FOR USE
FUNCTION SWITCH
- A. Lighting.
- B. Ventilation mode. The fan runs at low speed for 60 minutes.
- C. Speed 1 on fan motor.
- D. Speed 2 on fan motor.
- E. Speed 3 on fan motor. If the button is held in for 2 seconds, the fan switches to intensive mode. After 7 minutes, the fan motor returns to its previously set mode. The fan can be started and stop-ped with buttons B-E.
It is a good idea to turn on the fan before starting to cook, as this prevents cooking smells from spreading into the room. Adjust the speed of the fan depending on the type of food you are preparing. If possible, allow the fan to run at a low speed for a few mi-nutes after you’ve finished cooking. You may also wish to run the fan on the low setting when the oven is in use or after using the dishwasher.
CARE AND MAINTENANCE
Attention!
In order to ensure operation, quality and safety after servicing and maintenance, use only original parts.
Cleaning
The cooker hood should be cleaned with a damp cloth and washing-up liquid. With normal usage, the filters must be cleaned at least every other month. Clean more often after intensive use.
Remove the grease filters by opening the snap retainer, Fig. 11 Handle the filters carefully, taking care not to bend them.
Soak the filter in a solution of warm water and washing-up liquid. The filter can also be washed in a dishwasher.
Refit the grease filters after cleaning, making sure they snap firmly into place.
The motor core, side grilles and fan interior must be cleaned at least twice a year.
The motor core is removed by first disconnecting the contact on the side of the motor unit, Fig. 12A. Rotate the latches, Fig. 12B, that lock the motor core in place. Pull the unit outwards so that it is freed from the pins, and then downwards.
Attention!
The motor core should not be washed or exposed to moisture! Wipe with a slightly damp cloth and washing-up liquid.
One side grille is detached by lifting up the stop lug with a screwdriver and rotating the grille in the direction marked FREE, Fig. 13.
After washing and drying, assemble the parts in reverse order. Check that the parts snap into place and that the motor assembly and electrical connector are properly seated.
REPLACEMENT OF LED LIGHTING AND LED DRIVER
Attention!
The replacement of the LED lighting and LED driver must be carried out by an authorised professional. Contact the ser-vice organisation.
The lighting and driver must be replaced with an equivalent special light fixture and driver from the manufacturer or its service agent.
SERVICING AND WARRANTY
Check that the fuse is intact. Go through all the functions to check what is not working.
Contact Franke Service Tel. +46 (0)912-40 500 www.franke.se/service
They can help you fix the problem or refer you to the nearest service agent for fast and effective service.
The product is covered by the relevant AP-PLiA provisions.
PACKAGING AND PRODUCT RECYCLING
The packaging should be deposited at your nearest recycling point.
The symbol means that the product must not be treated as household waste. It should instead be taken to a collection point for the recycling of electrical and electronic components. By ensuring that the product is dealt with in the correct manner, you are helping to prevent the adverse environmental and health effects that could arise if the product was disposed of as regular waste. For further information on recycling, contact your local authority or waste disposal service, or the store where you purchased your product.
ECO-DESIGN DIRECTIVE
The product meets and is tested in ac-cordance with the eco-design require-ments of European Regulation 66/2014.
Documents / Resources
 |
SPISFL KT T45 HE FRI Cooker Hood [pdf] Instruction Manual T45 HE FRI Cooker Hood, T45, HE FRI Cooker Hood, FRI Cooker Hood, Cooker Hood, Hood |
Home 