Minka-Lavery 72790-143-L Shore Pointe Oil Rubbed Bronze Outdoor LED Wall Mount
Product Information
The product model number is 72790-143-L. The installation instructions for the product are as follows:
Installation Instructions
WARNING! Before starting the installation process, make sure to shut off power at the fuse or circuit breaker.
Preparing for Installation (Fig. 1)
- Turn off power at the circuit breaker and remove the old fixture along with its mounting hardware.
- Carefully unpack the new fixture and lay out all the parts in a clear area. Ensure that no small parts necessary for installation are misplaced.
- Thread two screws (C) into the pre-drilled holes in the mounting plate (B). Space them the same distance apart as the holes in the back plate. Secure them with nuts. The length of screws (C) into mounting plate (B) can be adjusted if needed.
- Attach the mounting plate (B) using outlet box screws (F) to the outlet box (A) (not included). Make sure the side of the mounting plate marked GND faces out.
Connecting the Wires (Fig. 2) - Connect the electrical wires as shown in Fig.2. Ensure that all wire connectors are securely fastened. If your outlet box has aground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate using the green screw (D) provided.
Finishing the Installation (Fig. 1) - Slide the back plate over screws (C) and secure it with cap nuts (H) (Fig. 1).
- To prevent moisture from entering the outlet box (A) (not included) and causing a short, use clear silicone sealant to outline the outside of the fixture back plate where it meets the wall. Leave a space at the bottom to allow moisture to escape (Fig. 3).
- LED information: The fixture includes 1 x AC LED 6W. Do not exceed the maximum wattage rating.
Replacing LED Module (Fig. 4)
The LED module can be replaced by a qualified electrician without cutting any wires or damaging any decorative elements attached to the fixture. Follow the installation steps for more details (Fig. 4).
- Shut off power. Remove the glass panel (J) by removing Glass (R), loosening screws (I) and plastic washer (P).
- Loosen screws (Q) and rubber washer (K) on the LED module.
- Loosen screws (M) and separate the top cover (O) from the fixture frame (N). Disconnect the plug on the wires and carefully remove the LED module (L).
- Reverse steps a-c for installing the new LED module. Note: The LED module should be provided by a specified supplier.
Product Usage Instructions
Your installation is now complete. Restore power to the outlet box and test the fixture. Please consult a qualified electrician to ensure correct branch circuit conductor and minimize the risk of fire.
INSTALLATION INSTRUCTIONS
Model # 72790-143-L READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
PREPARING FOR INSTALLATION (Fig. 1)
- Shut off power at the circuit breaker and remove the old fixture including the mounting hardware.
- Carefully unpack your new fixture and lay out all the parts in a clear area. Take care not to misplace any small parts necessary for installation.
- Thread two screws (C) into the pre-drilled holes in the mounting plate (B) spaced the same distance apart as the holes in the back plate and then secure with nuts. The length of screws (C) into mounting plate (B) may be adjusted if necessary.
- Attach mounting plate (B) using outlet box screws (F) to outlet box (A) (not supplied). The side of the mounting plate marked “GND” must face out (Fig 1).
CONNECTING THE WIRES (Fig. 2)
- Connect the electrical wires as shown in Fig.2. Making sure that all wire connectors are secured. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it.
Otherwise, connect the fixture’s ground wire directly to the mounting plate using the green screw (D) provided.
FINISHING THE INSTALLATION (Fig. 1) - Slide the back plate over screws (C) and secure with cap nuts (H) (Fig 1).
- To prevent moisture from entering the outlet box (A) (not supplied) and causing a short, use clear silicone sealant to outline the outside of fixture back plate where it meets the wall leaving a space at bottom to allow moisture a means to escape (Fig. 3)
- LED information (1 x AC LED 6W included.) (DO NOT EXCEED THE MAXIMUM WATTAGE RATING) (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
Replacing LED
Replacing LED module (Fig.4)
The LED module can be replaced by a qualified electrician without cutting of wire and without damage to any decorative element to which the fixture is attached. See installation steps for more details (Fig.4).
- Shut off power. Remove Glass (R), loosen screws (I) and plastic washer (P), then remove glass panel (J).
- Loosen screws (Q) and rubber washer (K) on the LED module.
- Loosen screws (M) and separate the top cover (O) from the fixture frame (N), then disconnect the plug on the wires. Carefully remove LED module (L).
- Reverse steps a-c for installing the new LED module.
Note: The LED module should be provided by a specified supplier.
“CAUTION-RISK OF FIR E CONSULT A QU ALIFIED ELECTRICIAN TO ENSURE CO RRECT BRANCH CIRCUIT CONDUCTOR”
ATTENTION RISQUE D’INCENDIE, CONSULTER UN ÉLECTRICIEN QUALIFIÉ POUR VOUS ASSURER QUE LES CONDUCTEURS DE LA DÉRIVATION SONT ADÉQUATS.
Documents / Resources
 |
Minka-Lavery 72790-143-L Shore Pointe Oil Rubbed Bronze Outdoor LED Wall Mount [pdf] Instruction Manual 72790-143-L Shore Pointe Oil Rubbed Bronze Outdoor LED Wall Mount, 72790-143-L, Shore Pointe Oil Rubbed Bronze Outdoor LED Wall Mount, Bronze Outdoor LED Wall Mount, Outdoor LED Wall Mount, LED Wall Mount, Wall Mount |
