Aimpoint 2 MOA Red dot reflex sight
Specifications
- Optical system: 1X magnification
- Magnification: Unlimited
- Eye relief: 18 mm
- Clear aperture: 2 MOA (H-2), 2 MOA (T-2)
- Dot size: 1 MOA / 4 MOA / 6 MOA (H-2), 2 MOA (T-2)
- NVD2 compatible: No (H-2), Yes (T-2)
- Optical coating: Anti-reflection (AR) coating
- Adjustment range: 1 click = 10 mm at 80 m = 13 mm in windage and elevation
- Dot intensity settings: 12 daylight positions (H-2), 4 NVD, 8 daylight positions (T-2)
- Optical signature: No forward optical signature from the dot beyond 10 meters
- Power source: One CR2032 Lithium battery (3 V)
- Battery life: More than 5 years of use at pos. 8
- Height of optical axis: 20 mm (0.8 in) over top surface of Picatinny/Weaver rail
- Materials: High-strength aluminum, black, semi-matte
- Sight housing Lens covers: Thermoplastic elastomer, black, non-glare finish
- Mechanical interface Configuration: Picatinny/Weaver rail
- Temperature range (operation): Not specified
- Water resistance: Not specified
Product Usage Instructions
Presentation
Technical Specification
The product features a 1X magnification optical system with unlimited eye relief and a clear aperture of 2 MOA or 4 MOA or 6 MOA (H-2) and 2 MOA (T-2). It is equipped with anti-reflection coating and offers adjustment settings for both windage and elevation. The dot intensity can be set to 12 daylight positions (H-2) or 4 NVD, 8 daylight positions (T-2). The sight operates on one CR2032 Lithium battery with a battery life of over 5 years at position 8. The product is constructed with high-strength aluminum housing and thermoplastic elastomer lens covers.
Operation
WARNING:
Ensure the weapon is not loaded and the safety selector is in the safe position before attempting to install, remove, or perform maintenance.
Install Battery
a. Remove the battery cap (6) using the tool (13A).
b. Insert the battery (7) with the positive end (+) facing the battery cap (6) as shown in Fig. 3.
c. Turn the rotary switch (8) to intensity setting 12 and tighten the battery cap (6) with the tool (13A).
d. Verify that the red dot is present and there is no gap between the battery cap (6) and the battery compartment.
Install the Sight on a Weapon
a. Loosen the shaft (15) with the tool (13D) to clamp the locking bar (14) around the Picatinny/Weaver rail.
b. Position the shaft (15) in a groove on the rail, push the sight forward towards the muzzle, and tighten the shaft using the tool (13D).
Zeroing
a. Open lens covers (11) and (12).
b. Adjust the intensity setting to ensure the red dot contrasts against the target.
FAQ
- Q: What is the battery type used in this product?
- A: The product operates on one CR2032 Lithium battery.
- Q: How long is the battery life of this product?
- A: The battery life is more than 5 years of use at position 8.
PRESENTATION
Aimpoint® red dot sights are designed for the ”two eyes open” method which greatly enhances situational awareness and target acquisition. The red dot follows the movement of the user’s eye while remaining fixed on target, eliminating any need for centering.
Technical specification
Optical system
- Magnification: 1X unlimited eye relief
- Eye relief: Unlimited
- Clear aperture: 18 mm /
- Dot size: 2 MOA1 / 4 MOA / 6 MOA (H-2) 2 MOA (T-2)
- NVD2 compatible No: (H-2) Yes (T-2)
- Optical coating: Anti-reflection (AR) coating
- Adjustments: 1 click = 10 mm at 80 m = 13 mm at 100 m (0.5 in at 100 yds)
- Adjustment range: ±1 m at 100 m (±1 yds at 100 yds) in windage and elevation
- Dot intensity settings: 12 daylight positions (H-2) 4 NVD, 8 daylight positions (T-2)
- Optical signature: No forward optical signature from Bthe dot beyond 10 meters
Power source
- Battery type: One CR2032 Lithium battery (3 V)
- Battery life3: More than 5 years of use at pos. 8
Height of optical axis
- Configuration: 20 mm (0.8 in) over top surface of Picatinny/Weaver rail
Materials
- Sight housing: High-strength aluminum, black, semi-matte
- Lens covers: Thermoplastic elastomer, black, non-glare finish
Mechanical interface
- Configuration: Picatinny/Weaver rail
Environmental specifications
- Temperature range: –30 °C to +60 °C
- (operation): (-22 °F to +140 °F) (H-2)
- -45 °C to +71 °C
- (-49 °F to +160 °F) (T-2)
- Water resistance: Submersible to 5 m (15 ft) (H-2)
- Submersible to 25 m (80 ft) (T-2)
- 1 MOA: Minute Of Angle, 1 MOA ≈ 30 mm at 100 m or ≈ 1 in at 100 yds
- 2 NVD: Night Vision Device
- 3 Battery life: Values valid at room temperature for a quality battery
overview
- Sight
- Adjustment cap
- Cap
- Elevation adjustment screw
- Windage adjustment screw
- Battery cap
- Battery (CR2032)
- Rotary switch
- Base
- Screws (4 pcs) for Base
- Lens cover, rear
- Lens cover, front
- Tool (ABCD)
- Locking bar
- Shaft (for Base)
OPERATION
WARNING: Ensure the weapon is not loaded and the safety selector is in the ”safe” position before attempting to install, remove or perform maintenance.
Install battery
- a Remove battery cap (6) using the tool (13A).
- b Insert battery (7) with the positive end (+) toward battery cap (6) as can be seen in Fig 3.
- CAUTION: Check that the O-ring is in good condition and in position to ensure that there will be no water leakage into the battery compartment.
- c Turn to the rotary switch (8) to intensity setting 12 (max.) and tighten the battery cap (6) with the tool (13A). When resistance is encountered, proceed to tighten until the battery cap (6) comes to a stop. d Verify that the red dot is present and that there is zero gap between the battery cap (6) and the battery compartment. See Fig. 1.
- NOTE: Remove the battery before putting the sight in storage for extended periods
Install the sight on a weapon
- a Loosen the shaft (15) with the tool (13D), to clamp the locking bar (14) around the Picatinny/Weaver rail
- b With the shaft (15) (=recoil stop) positioned in a groove on the Picatinny/weaver rail, push the sight forward (toward the muzzle) and tighten the shaft (15) using the tool (13D).
- c Tighten the shaft (15) until a light resistance is encountered. Proceed with another 1/4 to 1/2 turn until fully tightened (2 Nm / 1.5 ft·lb).
- CAUTION: Do not overtighten.
Zeroing
CAUTION: Do not continue to adjust windage and elevation if you encounter resistance. The mechanism can break if over-adjusted.
- an Open lens covers (11) and (12).
- b Adjust the intensity (8) to a comfortable setting for the red dot to contrast against the target.
- c To access the elevation adjustment screw (4) and windage adjustment screw (5), remove the adjustment cap (2) and the cap (3).
- d The adjustment cap (2) or the tool (13C) must be used to turn the adjustment screws. Place the knobs on the adjustment cap (2) into the recesses on the adjustment screws (4) and (5).
- e Windage adjustments (See Fig. 4)
- To move the point of impact to the right, turn the windage
- adjustment screw (5) counterclockwise.
- To move the point of impact to the left, turn the windage adjustment screw (5) clockwise.
- f Elevation adjustments (See Fig. 5)
- To move the point of impact up, turn the elevation adjustment screw (4) counterclockwise.
- To move the point of impact down, turn the elevation adjustment screw (4) clockwise.
- NOTE: Each click of the adjustment screws (4) (5) corresponds to a 13 mm movement of the point of impact at 100 meters, (3 mm at 25 meters and 26 mm at 200 meters or 0.5 in at 100 yds).
- g Confirm zeroing by firing at least three shots at a zeroing target. Checkpoints of impact to confirm the accuracy and repeat the above procedure if required.
- h After initial firing, ensure that the sight is securely installed on the weapon.
MAINTENANCE
- Extreme heat (moist or dry): No special procedures are required.
- Extreme cold: Extreme cold might shorten battery life. The rotary switch (8) can be harder to turn.
- Salt air: No special procedures are required.
- Seaspray, water, mud, and snow: Ensure that the battery cap (6), the adjustment cap (2) and the cap (3) are tightened before exposing the sight to sea spray, mud, and snow or before submerging the sight in the water. Tighten the adjustment cap (2) and the cap (3) by hand, and use the tool (13A) to tighten the battery cap (6). Keep lens covers (11) and (12) closed when the sight is not being used. Clean lenses with lens paper/cloth and wipe the sight dry as soon as possible after exposure to water, sea spray, mud or snow.
- Dust storms and sand storms: Keep lens covers (11) and (12) closed when the sight is not being used.
- High altitudes: No special procedures are required.
- NOTE: If used with a mount with a Quick Release (QR) lever mechanism, put a small amount of weapon oil on moving parts/surfaces in contact with each other periodically, e.g. when performing preventive maintenance on the weapon. Always follow instructions from the mount manufacturer.
- CAUTION: If used with a mount with a Quick Release (QR) lever mechanism: after mounting to rail, always check that lever stays locked if you try to open it without manipulating the release mechanism.
- CAUTION: Never clean the lenses with your fingers. Use lens paper/cloth. If lens paper/cloth is not available:
- To clear away debris (sand, grass etc.): blow away the dirt or rinse with clear water.
- To clean lenses: mist up the lenses or rinse with clear water and clean them with a soft piece of cloth.
TROUBLESHOOTING
The red dot does not appear or has disappeared
Clean contact surfaces in the battery compartment and verify that the battery (7) is working and that it is installed correctly. Verify that there is zero gap between the battery cap (6) and the battery compartment. See Fig. 1. If the rotary switch (8) is defective, notify the local dealer/armorer.
The sight is impossible to zero
If an adjustment screw (4) (5) is at its limit, check the alignment of the mount and barrel. If point of impact is moving, check the stability of the mount and weapon rail (or carry handle).
The front lens of the sight is tilted. Has the sight been damaged?
No. The optical system is designed for the front lens to be mounted in this way. See fig 2.
MOUNT INSTALLATION
To avoid damage to the sight (1) and for the proper assembly of the base (9) onto the sight (1), tighten the original screws (M3x4) by hand and with the tool (13D).
-
- CAUTION: Do not use thread locking fluid as it may damage the thread inserts of the sight (1).
- a Place the sight (1) upside down in your hand.
- b Press the base (9) against the Sight (1) and verify that there is zero gap.
- c Install the Screws (10) in a crosswise pattern. Tighten each screw until a resistance is encountered. Proceed with another 1/4 turn until fully tightened (1.35 Nm / 1.0 ft·lb).
- CAUTION: Do not overtighten.
WARRANTY
Aimpoint guarantees this product to be free from original manufacturer defects in material and/or workmanship under normal use for a period of two years for professional or frequent competition use and ten years for personal use from the date of purchase. Personal use shall mean: use of the sight in a way that implies less exposure than professional use.
Professional or frequent competition use shall mean daily or highly frequent use of the sight in professional activities (military or law enforcement) or under conditions that could be compared to as professional.
The warranty is valid provided that the sight has not been misused, disassembled or tampered with in any way.
Any attempt to disassemble or repair the product will void the warranty.
This warranty shall not apply to rubber and thermoplastic components.
This warranty is limited to the original purchaser of the product/s and is not transferable to any third party, unless otherwise followed from mandatory law.
Any warranty claim must be accompanied by a copy of the original receipt showing date of purchase and shall be notified as soon as can be reasonably required.
In case the product is defective in original manufacturer material and/or workmanship, Aimpoint undertakes either to repair, replace or compensate the purchaser its purchase price for such defective product.
AIMPOINT DISCLAIMS ALL IMPLIED WARRANTIES IN CONNECTION WITH THE SALE OF THIS PRODUCT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND THE IMPLIED WARRANTY OF MERCHANTABILITY. THERE ARE NO EXPRESS WARRANTIES THAT EXTEND BEYOND THIS WRITTEN WARRANTY OR ANY EXPRESS WARRANTY CONTAINED IN THE PRODUCT LITERATURE INCLUDED IN THE PACKAGING OF THIS PRODUCT.
Aimpoint Inc.
- 7309 Gateway Court Manassas, VA 20109, USA
- Phone: +1 703-263-9795
- Fax: +1 703-263-9463
- e-mail: info@aimpoint.com
- WWW.AIMPOINT.COM
© 2015, 2023 Aimpoint AB. [14140-7]
Documents / Resources
 |
Aimpoint 2 MOA Red dot reflex sight [pdf] User Manual 2 MOA Red dot reflex sight, 2 MOA, Red dot reflex sight, reflex sight, sight |
