AIIY STICK-NA Atrim Stick logo

AIIY STICK-NA Atrim Stick AIIY STICK-NA Atrim Stick product

Description & Features AIIY STICK-NA Atrim Stick fig 1

The Z-Stick Mini exposes the well-documented and proven Z-Wave Serial API via USB. It allows the host processor to control Z-Wave, Z-Wave Plus and Z-wave LR devices through the Z-Wave protocol. With the developer PC application software, PC Controller, or any software compliant with Z-Wave Serial API, the host is empowered to communicate with various Z-Wave devices through the Z-Wave Command Classes, making your computer the heart of your Z-Wave network.
Z-Stick Mini easily enables you to create your own Z-Wave gateway that is locally or remotely hosted with a PC or single- board computers, such as Beagle Bone Black and Raspberry Pi.

Product Specifications

General Specifications  

Potocal

  • USB Powered
  • RF Transmit current
  • RF Receive current
  • RF Transmit Power
  • RF Sensitivity
    • 9.6 kbps
    • 40 kbps
    • 100 kbps
  • Operating Temperature
  • Internal antenna Sleep Current
  • Range
ERF32ZG14 Zen Gecko SoC

Z-Wave Library

  • 5.00 ± 0.25 V
  • 22 mA (typ.)
  • 20 mA (typ.)
  • Up to +13 dBm (max.)
    • 101 dBm (typ.)
    • 100 dBm (typ.)
    • 97 dBm (typ.)
  • -20 to 75˚C
  • Metal spiral antenna
  • < 25 µA
  • 100 m open space line-of-sight
ERF32ZG23 Zen Gecko SoC

Z-Wave Library

  • 5.00 ± 0.25 V
  • 12 mA (typ.)
  • 10 mA (typ.)
  • Up to +14 dBm (max.)
    • 109.3 dBm (typ.)
    • 109.7 dBm (typ.)
    • 108.1 dBm (typ.)

Z-Wave Libraries  

  • Bridge Controller
  • Z/IP Application

Block Diagram

ERF32ZG14 Zen Gecko SoC  AIIY STICK-NA Atrim Stick fig 2

ERF32ZG23 Zen Gecko SoC  AIIY STICK-NA Atrim Stick fig 3

Quick Start Up

Here is a Quick Start Up guide to get Z-stick Mini to work with the Z-Wave PC Controller. The Z-Wave PC Controller is a PC application software tool that enables communications with Z-Wave nodes, such as switches and sensors.
Connect Z-stick Mini to your computer.
Install the Virtual COM Port (VCP) drivers and CP210x VCP Drivers, if required by your Operating System. The latest drivers are available at
http://www.silabs.com/interface-software. Note: The driver is WHQL certified. No installation is required for Window OS.

Note: The driver is WHQL certified. No installation is required for Window OS.

  1. Install and Run the Z-Wave PC Controller from Simplicity Studio. AIIY STICK-NA Atrim Stick fig 4
  2.  Click on the “Setting-wheel” AIIY STICK-NA Atrim Stick fig 5in the Right-Top corner of the PC Controller and select “Silicon Labs CP210x USB to UART Bridge”. Click OK.  AIIY STICK-NA Atrim Stick fig 6
  3. Click on Network Management. AIIY STICK-NA Atrim Stick fig 7
  4.  Z-Stick Mini is detected and appears as [S2] Pc Controller. The bottom panel displays that the Z-Wave Command Class is supported by Z-Stick Mini. AIIY STICK-NA Atrim Stick fig 8

FCC Warning

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Documents / Resources

AIIY STICK-NA Atrim Stick [pdf] User Manual
STICK-NA, STICKNA, 2A7QJSTICK-NA, 2A7QJSTICKNA, STICK-NA Atrim Stick, STICK-NA, Atrim Stick

References

Leave a comment

Your email address will not be published. Required fields are marked *