2014 Honda Accord Sedan L4-2.4L K24W1
Removal
Steering Joint – Disconnect
Disconnect the steering joint (CLICK HERE).
NOTE: Hold the steering wheel in the steering wheel holder tool.
A/C Compressor – Remove
Remove the A/C compressor without disconnecting the A/C hoses. Do not bend the A/C hoses excessively.
NOTE: Hang the A/C compressor with a wire tie.
Front Engine Mount Mounting Bolt – Remove
- Disconnect the vacuum hose (A).
- Remove the front engine mount stop (B) and the front engine mount mounting bolt (C).
Engine Undercover – Remove
Remove the engine undercover (CLICK HERE).
Engine Oil – Drain
Drain the engine oil (CLICK HERE).
Exhaust Pipe A or Under-Floor TWC/Exhaust Pipe A – Remove
Remove exhaust pipe A or under-floor TWC/exhaust pipe A:
- Exhaust Pipe A (CLICK HERE)
- Under-Floor TWC/Exhaust Pipe A (CLICK HERE)
Clutch Case Cover – Remove
Remove the clutch case cover (A) and the transmission mounting bolts (B).
Transmission – Support
Support the transmission with a transmission jack and a wood block under the transmission.
Lower Transmission Mount Mounting Bolt – Remove
Remove the lower transmission mount mounting bolts (A).
NOTE: Do not remove the bolt (B) from the lower transmission mount. If the bolt is removed, the lower transmission mount must be replaced as an assembly.
Transmission Jack – Remove
Remove the transmission jack and the wood block.
Front Subframe – Support
Lift and support under the front of the front subframe with a transmission jack.
Front Subframe Middle Mount Rubber Mounting Bolt – Loosen
Loosen the front subframe middle mount rubber mounting bolts (A) on both sides.
Front Subframe – Move
- Loosen the mounting bolts (A) from the front subframe (B) on rear side, so they are about 10 mm (0.39 in) from the mounting surface.
- Remove the mounting bolts (A) from the front subframe (B) on front side.
- Lower the jack slowly until the front subframe has dropped about 90 mm (3.54 in).
Oil Pan – Remove
- Using a flat blade screwdriver, separate the oil pan from the lower block in the places shown.
- Remove the oil pan.
Installation
Oil Pan – Install
- Remove all of the old liquid gasket from the oil pan mating surfaces, the bolts, and the bolt holes.
- Clean and dry the oil pan mating surfaces.
- Apply liquid gasket, (P/N 08718-0003, 08718-0004 or 08718-0009) to the engine block mating surface of the oil pan, and to the inside edge of the threaded bolt holes. Install the component within 5 minutes of applying the liquid gasket.
NOTE:
- Apply a 2.5 mm (0.098 in) diameter bead of liquid gasket along the broken line (A).
- If too much time has passed after applying the liquid gasket, remove the old liquid gasket and residue, then reapply new liquid gasket.
- Install the oil pan (A) with a new O-ring (B).
- Tighten the bolts in three steps. In the final step, torque all bolts, in sequence, to 12 N·m (1.2 kgf·m, 9 lbf·ft). Wipe off the excess liquid gasket on the each side of crankshaft pulley and flywheel/drive plate.
NOTE:- Wait at least 30 minutes before filling the engine with oil.
- Do not run the engine within 3 hours after installing the oil pan.
Front Subframe – Align
Align the front subframe (CLICK HERE).
Transmission Jack – Remove
Remove the transmission jack from the front subframe.
Front Subframe Middle Mount Rubber Mounting Bolt – Tighten
Tighten the front subframe middle mount rubber mounting bolts (A) to the specified torque on both sides.
Lower Transmission Mount Mounting Bolt – Install
Install the new lower transmission mount mounting bolts.
Clutch Case Cover – Install
Install the clutch case cover (A) and the transmission mounting bolts (B).
Exhaust Pipe A or Under-Floor TWC/Exhaust Pipe A – Install
Install exhaust pipe A or under-floor TWC/exhaust pipe A:
- Exhaust Pipe A (CLICK HERE)
- Under-Floor TWC/Exhaust Pipe A (CLICK HERE)
Engine Undercover – Install
Install the engine undercover (CLICK HERE).
Front Engine Mount Mounting Bolt – Tighten
- Tighten the new front engine mount mounting bolt (A).
- Install the front engine mount stop (B) using new nuts (C).
- Connect the vacuum hose (D).
A/C Compressor – Install
Install the A/C compressor.
Engine Oil – Refill
Refill the engine with engine oil (CLICK HERE).
Steering Joint – Connect
Connect the steering joint (CLICK HERE).
Wheel Alignment – Check
Check the wheel alignment (CLICK HERE).
VSA Sensor Neutral Position – Memorize
Do the VSA sensor neutral position memorization (CLICK HERE).
Steering Angle Sensor Neutral Position – Clear
Do the steering angle sensor neutral position clear (CLICK HERE).
TPMS – Calibration
Do the TPMS calibration (CLICK HERE).
Documents / Resources
 |
HONDA 2014 Honda Accord Sedan L4-2.4L K24W1 [pdf] Instructions 2014 Honda Accord Sedan, L4-2.4L, K24W1, 2014 Honda Accord Sedan L4-2.4L, 2014 Honda Accord Sedan L4-2.4L K24W1 |
ALLDATA 
