Universal Remote Control-LOGO

Universal Remote Control MRF-260 Optimizing Narrow Band Reception

Universal Remote Control MRF-260 Optimizing Narrow Band Reception-PRODUCT

HIGHLIGHTS

  • MRF-260 Installation Manual ©2007 Universal Remote Control, Inc.
  • The information in this manual is copyright protected. No part of this manual may be copied or reproduced in any form without prior written consent from Universal Remote Control, Inc.
  • UNIVERSAL REMOTE CONTROL, INC. SHALL NOT BE LIABLE FOR OPERATIONAL, TECHNICAL, OR EDITORIAL ERRORS/OMISSIONS MADE IN THIS MANUAL.
  • The Home Theater installation on the cover was designed and installed by Stone-Glidden of King of Prussia and Doylestown, PA.
  • The information in this manual may be subject to change without prior notice.
  • Complete Control is a registered trademark of Universal Remote Control, Inc.
  • All other brand or product names are trademarks or registered trademarks of their respective companies or organizations.

Introduction

The MRF-260 base station is an “addressable” base station. RF Addressing gives you the ability to control as many as 60 identical components throughout a house. To enable better range and reliability the MRF-260 is equipped with Narrow Band RF reception (like the MRF-350), so is only compatible with other Narrow Band remotes.

NOTE: The MRF-260 is ONLY compatible with Narrow Band remotes: the current versions of the MX-3000, MX-950, MX-900, TX-1000, MX-850, MX-650, and the MX-350 remote controls. The MRF-260 is compatible with all MX-950s, MX-900s, and TX-1000s, but is NOT compatible with MX-850, MX-650 or MX-350 remote controls manufactured before November 1, 2006, or an MX-3000 built before April 2005. You can identify the build date of a remote control by looking at the serial number. The first 6 digits indicate the build date. If the serial number appears as 122905 014054, the first 6 digits indicate that the remote was built on December 29, 2005.

  1. MX/TX remote controls send radio waves in every direction, so your client enjoys “No More Pointing” operation!Universal Remote Control MRF-260 Optimizing Narrow Band Reception-FIG- (1)
  2. The MRF-260’s integrated Narrow Band RF receiver receives commands from any Narrow Band remote control.
  3. Universal Remote Control MRF-260 Optimizing Narrow Band Reception-FIG- (2)
  4. Self-adhesive “Flashers” affix to the front panels of your client’s components (over the built-in IR sensor). The Flashers relay commands to components out of sight of the MRF-260’s Front Blaster. The flashers plug in to the MRF-260’s rear flasher line outputs via their 10-foot cables. Uniquely, the MRF-260 can also connect to rear panel IR Inputs via its two adjustable Outputs.

Features and Benefits

  • Interference Rejection and Extended Range via Narrow Band
    The MRF-260 receives RF (radio frequency) signals via its integrated RF receiver and antenna. The MRF-260 displays RF interference via a bright red Status LED, which flickers when interference is present if the ID is set to 0. Simply relocate the MRF-260 should interference occur.
  • Two Fixed IR Outputs
    The MRF-260 is equipped with two fixed IR line outputs with standard 3.5 jacks for standard IR emitter/flashers.
  • Two-Variable IR Outputs Match Rear Panel IR Inputs
    The MRF-260 is equipped with two adjustable IR line outputs. Each output can be individually matched to rear panel IR inputs on any component that is designed to be operated by a standard IR repeater. The outputs utilize a 3.5mm jack and are compatible with standard IR emitter/flashers as well.
  • Up To Fifteen Equipment Locations With Identical Components
    Each MX/TX remote is “addressable.” They can be programmed to specifically control components in a particular room by installing an MRF-260 base station at each location. In operation it’s simple: when you select a device located in the Den, the MX/TX remote only sends commands to the Den. When you select a device located in the Family Room, the MX/TX remote only sends commands to it.
  • A Single MRF-260 Can Control an Array of Identical Components or Identical Zones of a Multi-Zone Preamp/Matrix Switcher
    Each MRF-260 has four “addressable” IR Line Outputs. For example, you can control up to four identical TV’s with one MRF-260 or route volume commands for a specific zone to a particular zone IR input on a multi-zone preamp. If you have more than four identical components or zones, up to 15 additional MRF-260s can be installed to control them (thus allowing up to 60 identical components or zones in one house).

Parts Guide

The MRF-260 RF Base Station includes:

  • 1 – MRF-260 Base Station
  • 1 – Mounting Plate for wall mounting of the MRF-260
  • 4 – Screws for wall mounting
  • 1 – 9V-300mA Power Supply
  • 4 – Visible Flashers with 10-foot plug-in cables.
  • 4 – Extra self-adhesive pads for Emitters
  • 12 – Labels for IR Line Outputs
  • 1 – Screwdriver for Variable Outputs

Installation

  1. Unplug the MRF-260. Test all IR commands and macros line of sight.
  2. Power on all AV components including the TV. Turn on all of the lights and lower all dimmers to 50%. Power on anything that may create RF Interference (particularly devices with high speed microprocessors or hard drives).
  3. Check that the address wheel on the rear of the MRF-260 is set to ID#0 (the interference “sniffing” position).Universal Remote Control MRF-260 Optimizing Narrow Band Reception-FIG- (3)Check that the arrow pointer in the center of the wheel is pointed to 0, the default “interference sniffing” position. If it is not, use a small flat blade screwdriver (included) to set the RF ID# to 0.
  4. Connect the MRF-260 to its DC wall adapter and plug the wall adapter into a live AC outlet. Place the MRF-260 in a location at least 3 feet away from satellite receivers, cable boxes, HDTV tuners, DVRs, PCs or any other device with a high speed micro-processor (these generate broad band Radio Frequency Interference -RFI). Of course, you should keep in mind that the emitter cables are 10’ long.Universal Remote Control MRF-260 Optimizing Narrow Band Reception-FIG- (4)IF SET TO ID#0 The Status LED flashes when it receives ANY RF signal, including RFI. This makes ID#0 ideal for “sniff-ing” out RFI. IF SET TO ANY OTHER ID# The Status LED flashes ONLY when it receives a correctly addressed RF command.
  5. 5. Observe the Status LED of the MRF-260. If it is glowing or flick-ering you must relocate the MRF-260 to a location where the LED doesn’t flicker.
  6. If your installation location simply doesn’t offer you any choice and you are detecting interference everywhere you place the MRF-260, you have two last resort options:
    • Remove the MRF-260’s antenna. This will reduce the range enormously, but may still be enough for this client.
    • Admit defeat and install the two piece MRF-350 base station, which can have the RF Antenna module remote-ly located (even in another part of the house).
  7. Once you have found a location that is absolutely free of RFI with everything on, test to see if the range is adequate and that macro reliability is perfect. Start with the antenna angle set to 45 degrees and positioned so that the long side of the antenna is facing the customer’s favorite seating position.Universal Remote Control MRF-260 Optimizing Narrow Band Reception-FIG- (5)When testing, set both the remote and the MRF-260 to the same valid RF ID#. Keep in mind that zero (0) is not a valid RF ID#. Watch the Status LED on MRF-260 – it should light every time you press a button on the remote. This confirms that the signal was received and understood perfectly. If you repeat any button press multiple times and the Status LED lights correctly every time, you have no interference and a very reliable installation. If some of the presses do not light the Status LED, you still have some RFI. Your best strategy is return to step 3 and try to find a better location for the MRF-260.
  8. Now that the location is fixed, connect each of the emitters to the appropriate IR output and run the cable to the appropriate component. Do not attach the emitters to the front panel yet!Utilize the included preprinted labels to identify which emitter goes to which component. If you’d like to make your own, the slots for the labels have been sized at 12mm to enable a Brother P- Touch 12mm label to fit perfectly.

NOTE: TiVo, Replay TV, other DVRs, Satellite Receivers and Cable Boxes are all extremely sensitive to IR overload or saturation. For this reason, it is recommended that you always connect the IR flashers for these types of component to the Variable IR Outputs of the MRF-260.

Testing

  • Test a few commands for each device before fixing the flasher in place on the front panel of a device.
  • Since TiVo, Replay TV, Satellite Receivers and Cable Boxes are all extremely sensitive to IR overload or saturation, you should test them thoroughly. Put up the on screen guide and test the navigation arrows. Compare operation via RF to the original remote control. Operation should be identical. RF is not slower. If operation is inconsistent or sluggish, lower the IR line output and/or reposition the flasher.
  • If you still have sluggish operation, check that the remote control is set to a particular LINE OUT, rather than ALL. When IR commands are sent to all the flashers in a cabinet, you can have difficulty adjusting the IR Output. Reprogram the remote control to send IR commands only via a specific (1-4) Line Output, then readjust the IR Line Output level.

Note: Remember, the MRF-260 will NOT respond if you select IR line outputs 5 or 6. The MRF-260 has only four IR Line Outputs.

  1. Connect an IR emitter to each IR output and run the emitter wire to the front panel of each component. DO NOT STICK the emitter in place. ADJUST the level first.
  2. Adjust each of the IR Output levels for best operation. If the component operates best at minimum level, but is still operating sluggishly or intermittently, move the emitter farther away from the components IR sensor.

Front Blaster Overload

A few models of audio/video components can be overloaded by the Front Blaster. If you are having intermittent or inconsistent results with a particular component, try repositioning the MRF-260 and facing the Front Blaster in a different direction. If this improves the situation but is impractical, it may be necessary to utilize the self-adhesive flashers only and follow the steps below to Disable the Front Blaster. This will limit the number of components your MRF-260 can control to four. If you have more than four components you can purchase an additional MRF-260 or upgrade to an MRF-350.

Disabling the Front Blaster – Step by Step via PC

Note: If you are programming a URC MX “addressable” remote control that sets up without a PC, refer to the owners manual to dis-able the Front Blaster.
Open the PC software, then plug the MX PC programmable remote control into the PC. Open your saved configuration and follow these steps to turn off the front blaster:

  • Step 1 – Open the RF Setup Window
    The RF Setup window opens after selecting RF Control or Settings from the Program Menu of most MX/TX editors or from the Main Menu of the ProWizard.
  • Step 2 – Setup the Receiver
    Extend the RF Setup window by clicking on the RECEIVERS button.Universal Remote Control MRF-260 Optimizing Narrow Band Reception-FIG- (6)Universal Remote Control MRF-260 Optimizing Narrow Band Reception-FIG- (7)
  • Step 3 – Turn off the Front Blaster
    Click on the cell in the IR LED OUTPUT/IR BLASTER column. A list box will appear. Select OFF from the list.

Universal Remote Control MRF-260 Optimizing Narrow Band Reception-FIG- (8)Next, click on Close to apply your change.

Controlling Four Identical Components/Zones

There are several considerations to take into account when you are installing an MRF-260 to control an array of identical components:

  1. The RF ID# cannot be set to Code 0, the universal setting. You must use one of the fifteen unique IR Routing addresses.
  2. Each identical component must receive IR commands ONLY from a dedicated Flasher affixed to its front panel or a rear panel direct IR input. The SIGNAL of the remote should be set to RF ONLY for each identical component. IR can still be utilized for other devices in your system!
  3. You must note the NUMBER of the Flasher Output you have uti-lized for EACH of the identical components.

Identical Components/Zones – Step by Step via PC

  • Step 1 – Create and Program a Device for Each Component/Zone
    Try to name each device with a descriptive title. At a minimum, label them TV1, TV2, TV3 and so on.
  • Step 2 – Open the RF Setup Window
    The RF Setup window opens after selecting RF Control from the Program Menu or from the ProWizard’s Main Menu. The RF Setup window is composed of a “spread sheet” of options for EACH of your devices.Universal Remote Control MRF-260 Optimizing Narrow Band Reception-FIG- (9)By looking at the Signal column, you can see that the factory default programming sets all of the devices to send both IR and RF commands. If you look at the column for Flashers, you can see that the default sends IR commands for all devices to ALL of the flash-ers. Both options must be changed for identical components. Additionally, you must disable the Front Blaster (see page 6 for directions).
  • Step 3 – Adjust the Signal For Each of the Identical Devices
    The RF Setup window enables you to adjust the Signal output for each device individually, by clicking on the intersection of a row and a column and then selecting RF from the three options shown in the pull down list box. Select RF from the three options shown for EACH of the identical TVs. You may leave the other components of the system set to IR & RF.Universal Remote Control MRF-260 Optimizing Narrow Band Reception-FIG- (10)
  • Step 4 – Adjust the Flashers For Each of the Identical Devices
    The RF Setup window enables you to adjust which Flashers output by the remote control for each device individually, by clicking on the intersection of a row and a column and then selecting 1-4 from the seven options shown in the pull down list box.
    Select the correct Flasher (refer to your connection notes) for EACH of the identical TVs. You may leave the other components of the system set to ALL.
    See figure on the next page. In the figure below, each device is set to a specific flasher.Universal Remote Control MRF-260 Optimizing Narrow Band Reception-FIG- (11)Note: Remember, the MRF-260 will only respond to selections 1 through 4.
  • Step 5 – Make sure that the ID# is set on both the remote and on the wheel of the MRF-260.
    Click on the Receivers button and set the RF address to one of the first 15 addresses (1-9 or A, B, C, D or E). The second set of address-es is only supported by MSC units.Universal Remote Control MRF-260 Optimizing Narrow Band Reception-FIG- (12)
  • Step 6 – Close the RF window and Download to the Remote.

Programming For Multiple Equipment Locations

You can operate up to 15 different equipment locations, each with an MRF-260 assigned a unique Receiver ID#. You program each of your remotes to talk to the equipment locations you want by assign-ing each of your devices to a receiver. First, you must add and name your receivers for the locations they are placed in:

  • Step 1 – Open the RF Setup Window
    The RF Setup window opens after selecting RF Control from the Program Menu or RF Settings from the Main Menu of ProWizard.
  • Step 2 – Reveal the Receiver settings
    Extend the RF Setup window by clicking on the Receivers button of the RF setup window.
  • Step 3 – Add, Name and Assign Receiver ID#
    Using the controls at the bottom extended portion of the RF Control window, add new receivers and rename them for the equipment location.Universal Remote Control MRF-260 Optimizing Narrow Band Reception-FIG- (13)
  • Step 4 – Save and Download to your remote.

USA Limited Warranty Statement

Your Universal Remote Control, when delivered to you in new condition, is warranted against defects in materials or work-manship as follows: UNIVERSAL REMOTE CONTROL, INC. warrants this product against defects in material or workman-ship for a period of one (1) year and as set forth below. Universal Remote Control will, at its sole option, repair the product using new or comparable rebuilt parts, or exchange the product for a comparable new or rebuilt product. In the event of a defect, these are your exclusive remedies.

This Limited Warranty covers only the hardware components packaged with the Product. It does not cover technical assis-tance for hardware or software usage and it does not cover any software products whether or not contained in the Product; any such software is provided “AS IS” unless expressly provided for in any enclosed software Limited Warranty.

To obtain warranty service, you must deliver the product, freight prepaid, in its original packaging or packaging affording adequate protection to Universal Remote Control at the address provided in the Owner’s Manual. It is your responsibility to backup any macro programming, artwork, software or other materials that may have been programmed into your unit. It is likely that such data, software, or other materials will be lost during service and Universal Remote Control will not be responsible for any such damage or loss. A dated purchase receipt, Bill of Sale, Installation Contract or other verifiable Proof of Purchase is required. For product support and other important information visit Universal Remote Control’s website: http://www.UniversalRemoteControl.com or call the Universal Remote Control Customer Service Center (914) 835-4484.

This Limited Warranty only covers product issues caused by defects in material or workmanship during ordinary consumer use. It does not cover product issues caused by any other rea-son, including but not limited to product issues due to commer-cial use, acts of God, third-party installation, misuse, limita-tions of technology, or modification of or to any part of the Universal Remote Control product. This Limited Warranty does not cover Universal Remote Control products sold as USED, AS IS, REFURBISHED, so-called “B STOCK” or consumables (such as batteries). This Limited Warranty is invalid if the factory-applied serial number has been altered or removed from the product. This Limited Warranty is valid only in the United States of America. This Limited Warranty specifically excludes prod-ucts sold by unauthorized resellers.

TROUBLESHOOTING FAQS

  • Can I use flasher/emitters that I have already installed in the sys-tem to connect to the MRF-260?
    Yes, the flashers are compatible if they use 3.5mm mono mini plugs with the same polarity (Tip is data, sleeve is ground).
  • I’m getting inconsistent operation regardless of flasher level or position.
    Some components are easily overloaded with IR from nearby flashers. Prevent IR from affecting the problem component from other flashers or the front panel blaster by setting the device to a specific IR Line Output instead of ALL, then adjust the Line Output.
  • I have a row of identical TVs. I’ve correctly set the flasher outputs using the Editor software, yet when I send a command to one of them, the TV next to the selected TV also responds. How do I stop this?
    First, check the RF ID#, if the RF ID# is set to 0, IR routing does not work. Second, set the RF ID# from 1-9 or A-F on both the remote control and the rear of the MRF-260. Third, check that the flasher level is set to the mini-mum necessary. Fourth, check that the emitter is facing the component.

Specifications

  • Power Supply: 9V 300mA
  • IR Flasher Line Outputs: 3.5mm Mono Mini Jack
  • RF Frequency: 418MHz

Information To The User

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reason-able protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interfer-ence to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit dif- ferent from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Warning

Changes or modifications not expressly approved by the manu-facturer could void the user’s authority to operate the equip-ment.

Note: The manufacturer is not responsible for any Radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

500 Mamaroneck Avenue, Harrison, NY 10528

FREQUENTLY ASKED QUESTIONS

What is the Universal Remote Control MRF-260 Optimizing Narrow Band Reception?

The Universal Remote Control (URC) MRF-260 is a device designed to enhance and optimize the reception of narrow-band RF signals for remote control systems.

What are narrow-band RF signals?

Narrow-band RF signals are radio frequency signals that operate within a specific frequency range and are commonly used for wireless remote control systems.

How does the MRF-260 enhance narrow-band reception?

The MRF-260 typically uses advanced technology to improve the reception of narrow-band RF signals, resulting in more reliable and consistent control of devices.

What types of devices can benefit from the MRF-260's reception enhancement?

The MRF-260 is designed to enhance the reception of RF signals used in remote control systems for various devices, such as TVs, audio equipment, and home automation systems.

Can the MRF-260 be used with any brand of remote control system?

The MRF-260 is often compatible with a variety of Universal Remote Control systems, but it's important to verify compatibility with your specific model.

How is the MRF-260 connected to the remote control system?

The MRF-260 is typically connected to the main control unit of the Universal Remote Control system using appropriate cabling.

Does the MRF-260 require a power source?

Yes, the MRF-260 requires a power source to operate. It's usually powered using an external power adapter.

Can the MRF-260 improve the range of remote control signals?

Yes, the MRF-260 can enhance the reception range of RF signals, allowing you to control devices from a greater distance.

Does the MRF-260 work with both IR (infrared) and RF (radio frequency) signals?

The MRF-260 is designed to enhance RF signals. It may not directly impact the performance of IR signals.

Can the MRF-260 be used in commercial as well as residential settings?

Yes, the MRF-260 can be used in both commercial and residential settings to improve the performance of remote control systems.

Does the MRF-260 support bidirectional communication?

No, the MRF-260 is generally designed to enhance the reception of RF signals and doesn't typically involve bidirectional communication.

Is the MRF-260 compatible with modern smart home systems and devices?

The MRF-260 is more focused on enhancing narrow-band RF reception and may not have direct integration with modern smart home systems.

The MRF-260 is usually installed by connecting it to the Universal Remote Control system's main control unit and configuring the settings.

Can the MRF-260 optimize the reception for multiple rooms or areas?

Yes, the MRF-260's reception enhancement can often benefit multiple rooms or areas within its effective range.

Is the MRF-260 a standalone device, or does it require other equipment?

The MRF-260 is often used as an accessory with compatible Universal Remote Control systems and requires a compatible control unit for full functionality.

DOWNLOAD THE PDF LINK:  Universal Remote Control MRF-260 Optimizing Narrow Band Reception

References

Leave a comment

Your email address will not be published. Required fields are marked *