evenflo UMVVFCVT45YZICHYWTHW Shyft Rideshare All-Terrain Instruction Manual

Evenflo UMVVFCVT45YZICHYWTHW Shyft Rideshare All-Terrain

Wagon: Up to 55 lbs (25 kg) / Seat Up to 45 in (114.3 cm) / Seat

Read all instructions before assembly and use of the product.

KEEP INSTRUCTIONS FOR FUTURE USE.

• 2023 Evenflo Company, Inc.

OVERVIEW

1. Parent’s Handle
2. Adjustable Handle Button
3. Child’s Tray
4. Infant Car Seat Attachment Point (under Seatback Flap)
5. Seatback Flap
6. Fold Release Lever
7. Storage Basket
8. All-Terrain Rear Wheels
9. Brakes
10. Cupholder Attachment Mount (2)
11. Cupholder (2)
12. Child Tray Release Button
13. Parent’s Handle Flip Release
14. Infant Car Seat Retaining Strap
15. Swivel Wheel
16. Footwell
17. Canopy
18. Airflow Window
19. Visor
20. 3-Point Harness
21. Canopy Ring
22. Child Tray Mount
23. Seatback Zipper
24. Child Storage Pockets

WARNING
READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS! FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY OR DEATH!

• NEVER leave children unattended. ALWAYS keep children in view while in the product.
• Adult assembly is required. Take care when unpacking and assembling; contains small parts and some items with sharp edges.
• To prevent a possible choking hazard, remove and discard packing material before using this product.
• Avoid serious injury from falling or sliding out. ALWAYS use 3- a point harness.
• DO NOT carry or roll products on stairs or escalators with a child in it.
• DO NOT hang items on the parent’s handle or place them on the canopy as they can tip the product over and injure a child.
• ALWAYS exercise care when going over curbs or steps, and never use the product for anything other than used as described in these instructions. Use at a normal walking pace only; faster strolling can cause a loss of control and injury to the child.
• DO NOT place hot liquids in storage pockets or cupholders. Spills can burn you or your child.
• DO NOT use the product if any parts are missing or broken.
• DO NOT allow the child to climb on, into or out of the product unassisted and the top rail is lowered by a parent.
• DO NOT allow the child to stand on the footwell. The product may tip over and injure a child.
• DO NOT carry additional children, goods, or accessories in or on this product except as advised in these instructions. The product is intended for use with one or two children and to accommodate only the additional weights in storage as listed in these instructions.
• DO NOT allow the child to push or pull the product in any mode.
• DO NOT allow the child to sit, stand or climb over the child’s tray.
• DO NOT step on the parent’s handle in wagon mode.
• DO NOT allow the child to stand while the product is in motion.
• DO NOT allow the child to jump on the seat or footwell.
• ALWAYS ensure the product is in a fully locked position before using.
• NEVER leave the product on a hill or incline, even with brakes set, to avoid the product from tipping.
• To avoid accidental rolling, ALWAYS set brakes when the product is not being used.
• The carriage or stroller will become unstable if the manufacturer’s recommended load is exceeded.

WARNING

READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS! FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY OR DEATH!

• To avoid injuries from finger entrapment, keep the child away from this product when unfolding and folding it.
• AVOID STRANGULATION:
  • DO NOT suspend strings or toys from the canopy.
  • DO NOT place product anywhere near cords from window blinds, draperies, phones, etc.
  • DO NOT place items with a string around your child’s neck such as hood strings or pacifier cords.
  • If not properly secured, the child may slip into leg openings and strangle.
• When making adjustments to the product, ALWAYS ensure that all parts of the body are clear of any moving parts of the product particularly when switching modes.
• The canopy is not intended to provide complete UV protection.
• Sharp or heavy objects placed in pockets may cause damage to the product or injury to the child.
• If unable to securely attach your infant car seat to this stroller, remove the car seat and contact Evenflo ParentLink at 1- 800-233-5921 (USA), 1-937-773-3971 (Canada), or 800-706-1200 (México).
• To avoid product instability and tip-overs, DO NOT load storage pockets with over 1 lb (0.45 kg), and storage baskets with over 10 lbs (4.5 kg).
• DO NOT use Cargo Mode for transporting children.
• To avoid serious injury, NEVER use the product in any other configuration other than what is shown in the instruction manual. This product can be used in multiple modes (see pg. 8).
• Only use Evenflo SafeMax™ or any version of the LiteMax™ infant car seats with this stroller. Other infant car seats or carriers are not designed to fit the stroller frame and if used with this stroller may result in serious injury to your child.
• Before using the infant car seat with this stroller, read all the instructions provided with the infant car seat and keep the instructions stored properly for future use.
• Do not lift the stroller by using the infant car seat handle when installed on the stroller.
• To avoid serious injury, make sure the infant car seat is securely snapped onto the car seat mounts (see pg. 19).

IMPORTANT INFORMATION

Child Requirements

• Wagon – Only use the product with a child who is capable of sitting upright unassisted and maintains good neck control.
• Maximum weight: 55 lbs (25 kg) in each seat. / 10 lbs (4.5 kg) in basket.
• Cargo Mode: 110 lbs (49.8 kg) (Not intended for children)
• Maximum height: 45 inches (114.3 cm)

IMPORTANT: Read instructions carefully before use. Save these instructions for future reference. It is very important to assemble the product according to these instructions. If you are missing parts, do not use the product and call Evenflo ParentLink at 1-800-233 5921 (U.S.A.) 1-937-773-3971 (Canada), or 800-706-1200 (Mexico) to order replacement parts.

Registration Information
Please register this product so we can reach you if there is a safety alert or recall. We will not sell, rent, or share your personal information. To register your product, please complete and mail the card that came with it or visit our online registration at
www.evenflo.com/registerproduct.

For future reference, record the Model Number and Date of Manufacture below. You can find this information on one of the rear product legs.

• Model Number:
• Date of Manufacture:

IDENTIFICATION OF PARTS

YOUR PRODUCT CAN BE USED IN THREE DIFFERENT MODES: STROLLER MODE, WAGON MODE OR CARGO MODE.
After the stroller wagon has been assembled, you can choose to set the product up in Stroller Mode, Wagon Mode or Cargo Mode. Follow the instructions on pages 9–13 for assembly and modes of use.

ASSEMBLING YOUR PRODUCT

WARNING! DEATH or SERIOUS INJURY can occur.

Care must be taken when folding or unfolding the stroller to prevent finger injury to you or your child. Make sure the child is not in the seat or near the stroller when folding or unfolding.

NOTE: To protect flooring, place a protective covering (cardboard, towel, small rug or blanket) beneath the product during assembly.

1. To attach all-terrain rear wheels, push the wheel onto the rear wheel assembly until it clicks into place as shown. Repeat on the other side.
2. To attach the rear axle assembly, turn the stroller wagon over so the rear tube is positioned as shown. Align the rear axle assembly with rear tubes and push onto tubes until an audible click is heard. Pull on the rear axle assembly to make sure both are securely attached.
3. Locate front wheel assemblies. To attach the front wheel, line up the metal pin with a hole in the front wheel mount and push onto the frame as shown until it clicks into place. Repeat the process on the other side of the frame. Pull on the wheels to make sure both are securely attached. To remove the wheel, press the tab on the back of the wheel mount and pull.

1. To install the footwell board, turn the stroller over and slide the footwell board into the fabric at the centre of the stroller wagon.
2. Once the footwell board is in place, zip fabric closed as shown.
3. To attach the canopy, snap both canopy mounts into place on the stroller wagon until an audible click is heard.
   NOTE: Canopy is a one-side installation. Align canopy mounts with slots as shown.
4.  Pull up on both sides of the canopy rings to make sure it is locked into place.
5. To lift the parent’s handle, squeeze flip release levers on both sides of the handle and lift until it clicks into place.
6. To unfold stroller wagon, lock brakes. At the rear of the stroller wagon, squeeze the fold release button. Lift the top of the frame with the other hand until it clicks into place as shown.
   NOTE: A child tray handle or canopy ring can be used for folding and unfolding.
7. To assemble the front bar to the stroller wagon, fold the seatback flap, then align the bar at the front of the stroller wagon and sit nap into place until an audible click is heard. Pull on the bar to ensure it is fully attached.
8. Zip seatback fabric to wagon frame as shown.
9. To attach the rear bar with a basket to the stroller wagon, fold the seatback flap, then align the bar at the rear of the stroller wagon. Snap into place until an audible click is heard. Pull on the bar to ensure it is fully attached.
   NOTE: The infant car seat icon can be located on the seatback flap.
   IMPORTANT: Ensure the basket straps are not twisted when attaching the bar to the stroller wagon frame.
10. Zip seatback fabric to wagon frame as shown.
11. To attach the child tray, align the tray with attachment points on both sides. Push the tray down until both sides click into place.  To remove the tray, press the button with one hand while lifting the child’s tray from the stroller wagon with the other hand.

CONVERT TO WAGON MODE FROM STROLLER MODE

WARNING

• DEATH or SERIOUS INJURY can occur.

Care must be taken when folding or unfolding the stroller to prevent finger injury to you or your child. Make sure the child is not in the seat or near the stroller when folding or unfolding.

1. To convert to Wagon Mode, lock the brakes (see pg. 14).
2. Locate parent handle flip release levers. Squeeze levers while lifting the handle to rotate to Wagon Mode.
   • IMPORTANT: It is recommended that the parent handle is in shortest position in Wagon Mode (see pg. 15).

DO NOT use Cargo Mode for transporting children.

1. To convert to Cargo Mode, lock brakes (see pg. 14).
2. Press the fold-release button and lower the top of the frame using the child tray or canopy rings.
3. Locate parent handle flip release levers. Squeeze levers while lifting the handle to rotate as shown.

USING THE BRAKES

To avoid serious injury, always lock the brakes. Make sure the brakes are on by trying to push the product

• To lock, push the lever DOWN on the brake as shown.
• To unlock, pull the lever UP at the bottom of the brake as shown.

USING THE CANOPY

1. To extend the canopy, pull the canopy up as shown.
2. To close, push the canopy down as shown.
3. To shorten the canopy length, fold the visor up as shown.

CUPHOLDER
The cup holder is attached using a mounting clip that can be installed on either side and inside or outside of the parent’s handle.

1. To attach, slide the mount attachment onto the handle until it locks into place. To remove the mounting clip, press the tab and slide the clip from the parent’s handle.
2. To attach the cupholder, slide the cupholder down onto the mounting clip as shown.
3. To remove the upholder, press the ab towards center and slide up as shown.
   IMPORTANT: Remove cupholders before folding if mounted inside the parent’s handle.

USING PARENT’S HANDLE

To extend the parent’s handle, press the adjustable handle button and pull the handle out until it locks into position. To lower the parent’s handle to the shortest position, press the adjustable handle button and push the handle down until it locks into position.

NOTE: In Wagon Mode and Cargo Mode, it is recommended the parent’s handle is used in the shortest position.

SECURING YOUR CHILD
To avoid serious injury from falling or sliding out, ALWAYS use a 3-point harness.

1. For easy entry into the wagon, remove the child tray and lock the brakes. Press the fold-release button and lower the top of the frame using the child tray or canopy rings.
2. Lower the parent’s handle by squeezing flip release levers on both sides
   of the parent’s handle and lowering it to the bottom of the wagon frame.
   NOTE: The parent’s handle should be in the lowest position when children are entering or exiting the stroller wagon.
3. Once a child enters the wagon, lift the top of the frame back up using the canopy rings until it clicks into place and reattach child tray (see pg. 12). Push down on the top rail to ensure the frame is fully locked.
4. Squeeze flip release levers and lift to raise the parent’s handle until it clicks into the push mode position.
5. To attach waist straps to the buckle strap, insert buckles into the buckle strap as shown.
6. To unlock the harness, push the button on the buckle strap.
7. To tighten, pull the free end of the straps as shown.

ATTACHING INFANT CAR SEAT

• Only use Evenflo SafeMax™ or any version of the LiteMax™ infant car seats with this stroller. Other infant car seats or carriers are not designed to fit the stroller frame and if used with this stroller may result in serious injury to your child.
• Before using the infant car seat with this stroller, read all the instructions provided with the infant car seat and keep the instructions stored properly for future use.
• DO NOT lift the stroller by using the infant car seat handle when installed on the stroller.
• The parent’s handle MUST be in the longest position when using an infant car seat on a stroller wagon.
• If unable to securely attach your infant car seat to this stroller, remove the car seat and contact Evenflo ParentLink at 1-800-233-5921 (USA), 1-937-773-3971 (Canada), or 800-706-1200 (México).
• To avoid serious injury, make sure the infant car seat is securely snapped onto the car seat mounts.

1. To attach the infant car seat to the stroller wagon, lock the brakes, place the canopy down at the front of the wagon, and set up the product in Stroller Mode, as shown.
2. Unzip the seatback flap on the parent-facing side. Flip the seatback flap toward the centre of the wagon.
   NOTE: The infant car seat icon can be located on the seatback flap.
3. Ensure the child tray is connected to the centre of the wagon (see pg. 12).
   IMPORTANT: A child tray MUST be installed to attach the Infant Car Seat to the stroller wagon.
4. Pull the retaining strap from the pocket on the side of the stroller wagon as shown.
5. Attach the infant car seat to the attachment bar on the stroller wagon until it clicks into place as shown.
   NOTE: The infant car seat handle should always be in an upright position when used on the stroller wagon.
   IMPORTANT: The parent’s handle MUST be in the longest position when using an infant car seat on a stroller wagon (see pg. 15).
6. Pull the retaining strap up through the belt guide at the side of the infant car seat.
7. Once the retaining strap is installed, lift it on the infant car seat carry handle to ensure it is attached correctly.
8. Pull the wagon canopy up to cover the front seat of the older wagon as shown.
   IMPORTANT: When using the infant car seat on an older wagon, the wagon canopy should cover the Infant Car Seat back.

REMOVING INFANT CAR SEAT

1. To remove the infant car seat from the stroller wagon, lock the brakes and lower the agon canopy.
2. Remove the retaining strap from the belt guide at the side of the infant car seat.
3. To remove the infant car seat, squeeze the release handle at the rear of the seat and pull the infant car seat up from the stroller wagon.
4. Place the retaining strap back in the storage pocket on the side of the stroller wagon as shown.
5. Flip the seatback flaps out on the parent-facing side of the stroller wagon and reattach using a zipper.

FOLDING YOUR PRODUCT
Care must be taken when folding or unfolding the stroller to prevent finger injury to you or your child. Make sure the child is not in the seat or near the stroller when folding or unfolding.

1. Make sure the parent’s handle is in the shortest position by pressing the button and pushing it down into the frame lock until it clicks into place (see pg. 15).
2. Lower the parent’s handle by squeezing flip release levers on both sides of the parent’s handle and lowering it to the bottom of the wagon frame.
3. Press the fold-release button and lower the top of the frame using the child tray or canopy rings.
   NOTE: Once folded, the stroller wagon can be stored in a self-standing position as shown. Wheels can be removed for a more compact fold (see pg. 9)

CARE AND MAINTENANCE

• Clean minor spills and stains on cloth or plastic surfaces with cold water and mild soap. Air dry.
• Metal and plastic parts can be wiped clean with a soft damp cloth and dried with a soft cloth. DO NOT use abrasive cleaners or solvents.

Limited Warranty

For a period of 90 days from the date of original delivery of this product to the consumer, Evenflo warrants to the original end-user (“Purchaser”) this Product (including any accessories) against defects in material or workmanship. Evenflo’s sole obligation under this express limited warranty shall be, at Evenflo’s option, to repair or replace any Product that is determined to be defective by Evenflo and determined to be covered by this warranty. Repair or replacement as provided under this warranty is the exclusive remedy of the Purchaser. Proof of purchase and delivery in the form of a receipt, paid invoice, or bill of sale, and delivery confirmation evidencing that the Product is within the warranty period must be presented to obtain warranty service. This express limited warranty is extended by Evenflo ONLY to the original Purchaser of the Product and is not assignable or transferable to subsequent purchasers or end users of the Product. For warranty service, contact Evenflo’s ParentLink Consumer Resource Center at 1-800-233-5921 or www.evenflo.com.

EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS HEREBY DISCLAIMED. EVENFLO SHALL NOT BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL OR PUNITIVE DAMAGES OF ANY KIND FOR BREACH OF THE EXPRESS LIMITED WARRANTY ON THIS PRODUCT, OR ANY WARRANTY IMPLIED BY OPERATION OF LAW. OTHER THAN THE EXPRESS LIMITED WARRANTY SET FORTH ABOVE, THERE ARE NO OTHER WARRANTIES THAT ACCOMPANY THIS PRODUCT AND ANY ORAL, WRITTEN OR ANY OTHER EXPRESS REPRESENTATION OF ANY KIND IS HEREBY DISCLAIMED.

Note: This warranty gives you specific legal rights. You may also have other rights that may vary from state to state.

• www.evenflo.com
• USA: 1-800-233-5921, 8 AM – 5 PM E.T. Canada: 1-937-773-3971
• México: 800-706-1200

Documents / Resources

evenflo UMVVFCVT45YZICHYWTHW Shyft Rideshare All-Terrain [pdf] Instruction Manual UMVVFCVT45YZICHYWTHW Shyft Rideshare All-Terrain, UMVVFCVT45YZICHYWTHW, Shyft Rideshare All-Terrain, Rideshare All-Terrain, All-Terrain

References

• User Manual