TORO 3464-688C TimeCutter Riding Mowers
Specifications
- Product: All TimeCutter Max Riding Mowers
- Model Number: 3464-688C
- Country of Origin: USA
Product Usage Instructions
Installing the Back Cushion
For Machines with MyRide™ Suspension System Only
Parts Required:
- 1 Seat back
- 4 Bolts (5/16 x 1-1/4 inches)
- Slide the seat back onto the seat-base posts and align the holes.
- Secure the seat back using 4 bolts (5/16 x 1-1/4 inches). Torque the bolts to 19.7 Nm (14.5 ft-lb).
- Note: Insert the bolts from back to front.
Connecting the Battery
- Locate the battery and negative battery cable.
- Remove the plastic cap from the negative battery post.
- Remove the fasteners on the negative battery cable and use them to secure the negative battery cable to the negative battery post.
- Install the previously removed plastic cap.
Attaching the Seat-Tilt Cable
For Non-MyRide™ Machines Only
Parts Required:
- Seat-tilt cable
- Tilt the seat back partway.
- Attach the seat-tilt cable from inside the seat pan as shown.
- Lower the seat.
FAQ
- Q: How often should I check the tire pressure?
A: It is recommended to check the front and rear tyres for proper inflation regularly as per the Operator’s Manual guidelines. - Q: Can I adjust the motion-control levers after installation?
A: Yes, you can adjust the levers to your desired position after installation and tighten the knobs securely.
Installing the Back Cushion
Machines with MyRide™ Suspension System Only
Parts Required
| 1 | Seat back |
| 4 | Bolt (5/16 x 1-1/4 inches) |
- Slide the seat back on to the seat-base posts and align the holes.
- Secure the seat back using 4 bolts (5/16 x 1-1/4 inches). Torque the bolts to 19.7 N∙m (14.5 ft-lb).
Note: Insert the bolts from back to front
Connecting the Battery
- Locate the battery and negative battery cable.
- Remove the plastic cap from the negative battery post.
- Remove the fasteners on the negative battery cable and use them to secure the negative battery cable to the negative battery post.
- Install the previously removed plastic cap.
Attaching the Seat-Tilt Cable
Non-MyRide™ Machines Only
Parts Required
| 1 | Seat-tilt cable |
- Tilt the seat back partway.
- Attach the seat-tilt cable from inside the seat pan as shown.
- Lower the seat.
Installing the Rear Hitch
Parts Required
| 1 | Rear hitch bracket |
Remove the fasteners from the rear frame and use them to install the rear hitch bracket as shown.
Installing the Motion-Control Levers
Parts Required
| 2 | Lever assembly |
| 2 | Knob |
- Install the motion-control levers.
- Adjust the levers to the desired position.
- Tighten the knob.
Completing the Setup
Parts Required
| 1 | Key |
| 1 | Operator’s Manual |
| 1 | Operator training material |
Checking the Mower Adjustment
Adjust the side-to-side level and the front-to-rear blade slope. Use the relevant procedures in the Operator’s Manual to verify that the deck is level, and make any adjustments as necessary. Refer to the Operator’s Manual for more information.
Checking the Tire Pressure
Check the front and rear tires for proper inflation; refer to Checking the Tire Pressure in the Operator’s Manual for the recommended inflation pressure.
Checking the Side-Discharge Chute
Remove the packing restraint holding the side discharge chute up and lower the chute int place.
Checking the Engine-Oil Level
Before you start the engine and use the machine, check the oil level in the engine crankcase.
Organizing the Material
Keep all the following items with the machine:
- Ignition key
- Operator’s Manual
- View the operator training material before operating the machine
© 2024—The Toro® Company 8111 Lyndale Ave So Bloomington, MN 55044
Register at www.Toro.com
Original Instructions (EN) Printed in the USA All rights reserved
Documents / Resources
 |
TORO 3464-688C TimeCutter Riding Mowers [pdf] Instruction Manual 3464-688C TimeCutter Riding Mowers, 3464-688C, TimeCutter Riding Mowers, Riding Mowers, Mowers |
