Contents hide

800, 900 and 1000 Base and Corner Base Unit Assembly

TH Note: If fitting a “True Handleless” kitchen, some components will differ to those shown in this instruction and will also be packaged separately. Please refer to your True Handleless guide to Receiving for further details on the different components and difference in installation.

bsi Base and Corner Base Unit 1        bsi Base and Corner Base Unit 2

bsi Base and Corner Base Unit 3      bsi Base and Corner Base Unit 4

Components

Components

Important Information – True Handleless Kitchens Installers: See Note Above TH
Bsi
FM 665131
Caution: Some pieces of hardware could be hazardous to small children. Keep all these items out of reach and do not leave children unattended in the assembly area.

Please read these instructions carefully before proceeding. Refer to the Guide to Receiving and Installing your Kitchen booklet for further information.
Note: Due to variation in wall conditions no screws are supplied for fixing the units to the wall. If in doubt consult an expert. Assemble the unit on a clean solid work surface.
In the interest of continuing improvements we reserve the right to amend or adjust the specifications without prior notice. Errors and omissions excepted.
These units may be fitted with a drawer system. The drawers are supplied separately. These instructions show the runner positions for the drawer system.
Follow the instructions supplied with the drawers for drawerbox assembly.
Every effort has been made to ensure that this product leaves the factory in perfect condition. In the unlikely event that an item is damaged or incorrect, please contact the customer services department.

Note – Fitting Handles: (1) Decide where you are going to position each handle to maintain symmetry around your kitchen. (2) Measure the handle centres and mark off each door/drawer position. (3) Drill through the door/drawer using a fine drill (<2.5 mm), then drill back from the rear face using a 4.5 mm drill. (4) Attach with the fixings provided with your handle.

Ref. No.    Item                                                      Quantity

150101       150101  3.5x12mm                                       14
150202       150202 4x12mm                                         16
150201       150201 4x15mm                                  16/20
150199       150199 4.5x45mm                       4
150198       150198 55mm Carcase Screw       3
154082        154082                                            6
154084       154084                        1
154085        154085                                                         7
154004        154004                                     8
154027        154027                                                            6
154068        154068                                                      8
154047        154047                                                2
152181        152181                                                     4
152162        152162                                                           4
150308        150308                                                   2
150309        150309                                                            2
152401        152401                                                            4/5
152418        152418                                                 4/5
152402        152402                                                     2
152148        152148                                                          4
151999        151999                                                                      12
151500        151500                                                       2

Tools Required

Drill            G-Clamp

Drill                                                            G-Clamp (pair)

Medium Crosshead Screwdriver           Hammer

Medium Crosshead Screwdriver                 Hammer

Large Flathead Screwdriver           Tape Measure

Large Flathead Screwdriver                        Tape Measure

Spirit Level            Bradawl

Spirit Level                                                  Bradawl

1 – 2 Assembly Instructions

TH Modification required at this stage, see True Handleless guide for further details.

Assembly Instructions-A     Assembly Instructions-B

Drawer Runner

Drawer Runner

Front                      1 x ‘L’; 1 x ‘R’

x4  x4

Fit as third screw x2

Fit as third screw

Assembly Instructions 1         Assembly Instructions 1-A          Assembly Instructions 2

1. 154082                2. 154004

154082                 6                    154004                     6

3 – 4

Note: Drill centre holes of B and E for Base Units. For Corner Base Units consult kitchen plan for door size and drill accordingly.

Assembly Instructions 3-4-A Assembly Instructions 3-4-B

Scrap wood                                      Scrap wood

Assembly Instructions 3   Assembly Instructions 3-A  Drill   Assembly Instructions 4

3.

154085

154085  6

5 – 6

Assembly Instructions 5

TH Modification required at this stage, see True Handleless guide for further details.

Assembly Instructions 5-A   Assembly Instructions 6

Do Not Over Tighten

Do Not Over Tighten

Start            Locked

7 – 11

Scrap wood

Assembly Instructions 7-11

8.

150199

150199                  4

Assembly Instructions 8 Assembly Instructions 9 Note: Countersunk screw goes into back panel D.

9.

150101         150202           154068

150101   2          150202    2          154068         2

10.

150202    154047

150202    4    154047              2

Assembly Instructions 10 Assembly Instructions 11   Drill

Note: Only drill if drawers are being fit. Base Units drill as indicated. Corner Base Units consult kitchen plan for door size and drill accordingly. Only drill from the lower set of holes

12 – 13 Without Drawers

 Without Drawers 12-13

TH Modification required at this stage, see True Handleless guide for further details.

12.

154004   Without Drawers 12 Assembly Instructions 1-A

154004                    2

13.

150198           Without Drawers 13

150198                 2

14 – 15 With Drawers

 With Drawers 14-A With Drawers 15

With Drawers 14  With Drawers 15-A   With Drawers 15-B

14.                             15.

154085                  154084

154085   1                  154084                                  1

16 – 17 With Drawers

 With Drawers 16-17

With Drawers 16   With Drawers 17

Do Not Over Tighten

Do Not Over Tighten

Start            Locked

With Drawers 16-17-B

Drawer Runner

Drawer Runner

Front                      1 x ‘L’; 1 x ‘R’

x4  x4

Fit as third screw x2

Fit as third screw

18 – 20 With Drawers

 With Drawers 18-20

18.                      19.                  20.

154004  150198   150198

154004           150198        150198          1

With Drawers 18 Assembly Instructions 1-A With Drawers 19   With Drawers 20

21 – 22

With Drawers 21 With Drawers 21-A With Drawers 21-B

21.

152401                           150201

152401 4/800 & 900  5/1000    150201 16/800 & 900   20/1000

With Drawers 22  With Drawers 21-C

With Drawers 22-B

22.

152418

152418              4/800 & 900   5/1000

23 – 25 Installation Instructions

23.

150202                 154068

150202      2                154068         2

TH Modification required at this stage, see True Handleless guide for further details.

Installation Instructions 23     Installation Instructions 24 Drill

24.

150308        150309

150308            2       150309    2

Installation Instructions 23-25  Installation Instructions 25

25.

150199

Appropriate to wall type (Not supplied)         2

26 – 29

26.

151500

151500     2

Installation Instructions 26

Installation Instructions 27-A

27.

152402    150101

152402             2   150101    4

Installation Instructions 28

28.

154027

154027       6

 Installation Instructions 26-29

30 – 31

Installation Instructions 30

Installation Instructions 31 Note: Do not over tighten screws or use a power screwdriver.
Installation Instructions 31

Installation Instructions 31-B Softclose ON_OFF

31.

150101

150101        8

32 – 35

Installation Instructions 32-35 Installation Instructions 34 Installation Instructions 35

34.                         35.

151999               152148

151999    4              152148         4

Installation Instructions 32  Installation Instructions 33 Installation Instructions 33-B Installation Instructions 33-C

36 – 37 Fixed Fascia Fitting

Fixed Fascia Fitting 36 Fixed Fascia Fitting 36

36.

150202           154068           151999

150202     2/4            154068     2/4            151999     4/8

37.

150202

150202      2/4

Fixed Fascia Fitting 37  Fixed Fascia Fitting 37-Main

38 Corner Post Fitting

Corner Post Fitting 38 Note: Fittings are packed with the Corner Post.

Corner Post Fitting 38-A   Corner Post Fitting 38-B

TH Modification required at this stage, see True Handleless guide for further details.

38.

150124           154081

150124       12            154081         6

39 – 41 Corner Post Fitting

TH Modification required at this stage, see True Handleless guide for further details.

Corner Post Fitting 39-41

Note: Fit corner post to adjacent unit, then fit optional blanking panel to corner base unit, finally attached corner post to corner base unit mullion. Use appropriate number of screws (not supplied). Any excess/hangover does not need to be trimmed as it will be concealed in the void.

40.                             39. 41.

150124            150124

Not Supplied 6-10    150124 6

Corner Post Fitting 40 Corner Post Fitting 39-41-A  Corner Post Fitting

Unit Size
(mm)
Required
Door
Size (mm)
Total Length
in Plan (mm)
Void
“x” (mm)
800mm 300 925 125
800mm 400 1025 225
800mm 500 1125 325
1000mm 400 1025 25
1000mm 500 1125 125
1000mm 600 1225 225

Ref. 170801 (05)

Documents / Resources

bsi Base and Corner Base Unit [pdf] Installation Guide
Base and Corner Base Unit, 800, 900, 1000, FM 66513, 170801 05

References

Leave a comment

Your email address will not be published. Required fields are marked *