Mounting instructions
BC.HTA.41.682.20000
contains
HTA.41.682.10000
HTA.41.682.11000
BC.HTA.00.682.11100
BC.HTA.00.682.11000
BC.LOC.00.682.10000/S
HTA.41.682.10000 Motorcycle Saddle Bag
READ AND SAVE THESE MOUNTING INSTRUCTIONS
Item No.: HTA.41.682.10000 & 11000
Revision: 00 – Datum / Date: 03 – 2022
SLH side carrier LH1
Thank you for choosing this premium product from SW-MOTECH. Please carefully read and understand all instructions, safety messages and warnings in this mounting instructions prior to installation and use of this product to avoid injury.
This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop. Keep these mounting instructions as reference.
SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!
SAFETY ALERT SYMBOL
This safety alert symbol is used throughout these mounting instructions to warn of the possibility of death, bodily injury or other warnings. The words DANGER, WARNING and CAUTION are used with this safety alert symbol to convey important safety messages and information related to the installation and use of this product. These words along with the safety alert symbol mean:
DANGER: Indicates a hazardous situation that, if not avoided, will result in death or serious injury!
WARNING: Indicates a hazardous situation that, if not avoided, could result in death or serious injury!
CAUTION: Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury!
NOTICE: Important information, but not death or injury related (property damage only]!
WARNING: The installation and/or maintenance of this product requires advanced mechanical skills, the proper tools, and a thorough understanding of tool use and torque specifications.
For your own safety, SW-MOTECH recommends having installation and/or maintenance carried out by a qualified and certified motorcycle mechanic.
WARNING: Should you choose to self-install this product, carefully and completely read all intallation and safety instructions before installation and use, and follow all the directions and safety precautions given in the mounting instructions to avoid serious injury or death. Also pay attention to all relevant information in the vehicle manual during intallation and use.
IF YOU DO NOT UNDERSTAND ANY PART OF THESE INSTRUCTIONS, OR NEED CLARIFICATION OF ANY INSTRUCTION, DO NOT ATTEMT TO MOUNT THIS PRODUCT WITHOUT CONTACTING SW-MOTECH FOR ASSISTANCE.
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included.
CAUTION: Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the engine/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools and wear always safety glasses and hand protection. Have another person help you.
MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturer specifications or replaced by parts and hardware delivered by SW-MOTECH.
WARNING: Secure all threads, unless otherwise specified, with medium- strong strength liquid thread locker. Torque specifications undefined by SW-MOTECH must be obtained from the vehicle manufacturer or by a certified motorcycle workshop!
FUNCTION CHECK: After installation also make sure that no moving parts are obstructed, and function of the vehicle is not hindered in any way. Cables and hoses must not rub and/or be pinched.
WARNING: Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all connections and the proper fit of the product. Installed accessories can change driving behavior/stability of the vehicle.
| Packed by: | Date of packaging: |
SW-MOTECH GmbH & Co. KG
Ernteweg 7-10
35282 Rauschenberg
Germany
Tel. /phone + 49 (0)6425 / 8168 – 050
Fax / fax + 49 (0)6425 / 8168 – 10
info@sw-motech.com
www.sw-motech.com
PARTS LIST
| Step | No. | Item No./ Description a | Part | Quantity b | N.m c |
| HTA.41.682.10000 | SLH Side Carrier left | ||||
| 2 | (1) | HTA.41.682.001 | Side Carrier; left | 1 / 1 | |
| (2) | HTA.18.682.017 | Spacer | 1 / 1 | ||
| (3) | M6 x 20; DIN 7991 | Countersunk Screw; black | 1 / 1 | 8 | |
| (4) | KES.RD.210.0300.02.GL | Plastic Plug | 1 / 1 | ||
| HTA.41.682.11000 | SLH Side Carrier right | ||||
| 2 | (5) | HTA.41.682.002 | Side Carrier; right | 1 /1 | |
| (6) | ALK.00.165.084 | Countersunk Part | 1 /1 | ||
| (7) | M6 x 16; DIN 7991 | Countersunk Screw; black | 1 /1 | 8 | |
| (8) | 0 6,4; DIN 9021 | Washer; black | 1 /1 | ||
| (9) | M6; DIN 6927 | Lock Nut with Flange; black | 1 /1 | ||
| HTA.41.682.10000 & 11000 | SLH Side Carrier left & right | ||||
| 2 | (10) | M8 x 110; DIN 7991 | Countersunk Screw | 1 /1 | 20 |
| (11) | 0 20 /0 8,4 / h 25 | Spacer; black; height 25 mm | 1 /1 | ||
| (12) | 0 16 / 0 8,5 / h 25 | Spacer; black; Hohe 25 mm | 1 /1 | ||
| (13) | M8 x 100; DIN 7991 | Countersunk Screw | 1 /1 | 20 | |
| (14) | 0 25 / 0 8,4 / h 42 | Spacer; black; height 42 mm | 1 /1 | ||
| (15) | 016/08,4/h 17 | Spacer; black; Hale 17 mm | 1 /1 | ||
| 8.8 | Coarse Thread | ∅ | M4 | M5 | M6 | M8 | M10 | M12 |
| Steel CL 8.8 | N.m | 2,8 | 5,5 | 9,6 | 23 | 46 | 79 |
| 10.9 | Coarse Thread | ∅ | M4 | M5 | M6 | M8 | M10 | M12 |
| Steel. CL 10.9 | N.m | 4,1 | 8,1 | 14 | 34 | 67 | 115 |
Note:
a All measurements in millimeters.
b The second number indicates the total quantity of the part in the delivery.
c No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.
MOUNTING
READ AND SAVE THESE MOUNTING INSTRUCTIONS
WARNING: Always wear eye and hand protection!
WARNING: Always use appropriate tools!
NOTICE: The following mounting steps show the mounting of the left side carrier. Mount the right side carrier in the same way.
Remove the shown screws from the vehicle.
Attach the spacer (2) to the left side carrier (1).
WARNING: Use liquid thread locker!
Tighten the screw as specified.
Then insert the plastic plug (4) into the spacer (2).
Attach the countersunk part (6) to the right side carrier (5) as shown in the detail drawing.
Tighten the screw as specified.
Attach the side carriers [1] / (5) to the vehicle.
WARNING: Use liquid thread locker!
Tighten the screws as specified.
PRODUCT SPECIFIC INFORMATION
WARNING: It is essential to observe the country-specific regulations regarding the lighting equipment (reflectors)!
If the reflectors mounted to the vehicle in the factory setting are covered by the side carriers, the reflectors must be removed and/or attached elsewhere in the same mounting position!
NOTICE: Observe the country-specific regulations concerning vehicle registration/operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
MOUNTING INSTRUCTIONS
Legend Gear side case LH1 / LH2
Item No.: BC.HTA.00.682.1**0*
Revision: 00
Date: 04- 2021
Thank you for choosing this premium product from SW-MOTECH.
Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop. Installation and/or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and/or stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration / operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor / exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
FUNCTION CHECK: This is a universal product. For this reason make sure BEFORE the first use, that the product can be fixed properly and used without problems with your vehicle type. After fixation also make sure that no moving parts are obstructed and the function of the vehicle is not hindered in any way. Lamps as taillight and turn signals must not be limited in their function. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions.
PRODUCT SPECIFIC INFORMATION
ATTENTION: Riding with this product may affect the motorcycles driving and braking performance!
ATTENTION: Before riding and at each stop [every 200 km) check proper fixation of the product!
| Maximum Load | Maximum Speed |
 LH1: 5 KG (2,2 tbs) |
 130 km/h (80 mph) |
| Maximum Load | Maximum Speed |
| LH2: 10 KG (4,5 tbs) |
130 km/h (80 mph) |
ATTENTION: The maximum load must not be exceeded! The maximum vehi load specified by the manufacturer must not be exceeded!
ATTENTION
NOT FOR OFFROAD-USE!
SW-MOTECH GmbH & Co. KG
Ernteweg 7-10 – 35282 Rauschenberg – Germany
Tel. / phone + 49 (0)6425 / 8168 – 050
Fax + 49 (0)6425 / 8168 – 10
info@sw-motech.com
www.sw-motech.com
PARTS LIST & CARE
CARE
Clean the product periodically or after each trip, as dust and dirt have a wear-effect and permanent stains can be prevented. Clean the product after riding in salty conditions, to avoid damage from salt.
First remove dust and encrustations with a soft dry brush. Remove stubborn deposits with a soft cloth and warm soapy water. Do NOT use strong cleaning agents, rough cleaning tools or high pressure washer! Then rinse with clear water.
Before re-use dry the product for at least 24 hours in the air (not in direct sunlight).
FIXATION
Assemble the components as shown in the drawing.
Pay attention to the side-specific alignment of the bolt, as emphasi- zed in the schematic drawing.
ATTENTION: Use liquid threat locker!
Tighten the screw as specified.
Loop the string as shown.
NOTE: The BC.LOC.00.682. 1000+ [+] is sold seperately.
Disassemble the components and attach them to to bags lid as shown.
Hang the bag [1) into the sockets of the mounting bracket attached to your vehicle.
Pay attention that both retaining elements are completely hooked into the socket contours of the mounting bracket.
Secure the bag (1) with the quick turn fastener (3), by inserting it into the opening and turning it clockwise.
Pay attention to the audible clicking sound.
The inserting position of the quick turn fastener differs depending on the vehicles’ side.
Attach the string of the quick turn fastener to the loop on the inside of the bag.
ATTENTION: Before each ride, lock the lid of the bag.
Thoroughly clean the front of the lid from grease and dirt.
Attach the reflector (4) to the lid as shown in the drawing.
MOUNTING INSTRUCTIONS
Item No.: BC.LOC.00.682.10000/S .-
Revision:00 . 01-2019
Legend Gear lock set
| No. | Item No. / Description | Quantity |
| (1) | 2/2 | |
| (2) | 2 /2 | |
Errors and omissions excepted. Technical and design modifications are subject to change.
Copyright by
SW-MOTECH GmbH & Co. KG
Documents / Resources
 |
sw-motech HTA.41.682.10000 Motorcycle Saddle Bag [pdf] Installation Guide HTA.41.682.10000 Motorcycle saddle Bag, HTA.41.682.10000, Motorcycle saddle Bag, saddle Bag |
