VOCOO 6202 Wireless Thermometer Indoor Outdoor Hygrometer User Manual

Wireless indoor/outdoor
Temperature and Humidity MonitorModle:6202

Diagram

Indoor Device

1. Outdoor temperature humidity 2. Indoor temperature humidity 3. Comfort level: DRY/COMFORT/WET 4. Date 5. Time 6. Backlight touch button

7. ℉/℃ conversion/ Clear the MAX/MIN temperature humidity data 8. Time, 12/24H format conversion 9. Wall hanging hole 10. Down/Reconnect MAX/MIN 11. Up 12. Tabletop Stand 13. Battery compartment

1. Power supply: 2*AAA battery
2. Two mounting methods: stand and wall hanging
3. Indoor temperature measurement range: -10℃~60℃(14℉~140℉)
4. Indoor temperature lower than -10℃, LL is displayed
   Indoor temperature higher than 60℃, HH is displayed
5. Humidity measurement range: 10%~99%
6. Temperature °C/℉ Switch
7. Temperature accuracy range: ± 1℃
8. Humidity accuracy range: ±5% RH
9. Refresh rate: 10S
10. Low battery warning for indoor / outdoor device
11. Backlight touch button(15s)
12. Automatically clearing the maximum and minimum values of temperature and humidity within 24 hours

Calibration

In case the temperature or humidity readings need becalibrated same to your other devices or product placement or environmental factors impact your data accuracy. Calibration can improve accuracy.
1. To access calibration mode,press the [+]and[–] buttons and hold together until the temperature number begins to flash, release the both button and just press the [+]or[–] button to adjust the temperature. (Max士5°C, Max土41°F)
2. Press the [℉/°C] button until the humidity number begins to flash, release the button and press the [+] or[–] button to adjust the humidity. (Max土10%)
3. Press the [℉/°C] button to save your adjustments.
Or after 15 seconds of inactivity, the display will save the adjustments and exit calibration mode.

Note:

1. Calibrations will be erased if the batteries are removed.
2. The display will automatically return to normal mode without saving data after flashing 10 times Without pressing any button.
3. Calibrations only available for the indoor temperature and humidity because outdoor air flow is uncontrolled.

Backlight

Touch [] button once to turn on backlight and 15s automatically turned off.

Temperature and Humidity Trend

1. [] Indicates that the temperature and humidity are on an upward trend
2. [] Indicates no change in temperature and humidity
3. [] Indicates that the temperature and humidity are on an downward trend

℃/℉ Conversion

1. Short pressing the [℉/°C] button to switch between Celsius/Fahrenheit.
2. Long pressing [℉/°C] button to clear the maximum and minimum temperature and humidity values.

Comfort Level

DRY	Humidity is below 29% ( 10%, 11-20%, 21-29%)
COMFORT	Humidity is between 30%-69% ( 30-39%, 40-60%, 61-69% )
WET	Humidity is above 70% ( 70-79%, 80-89%, 90-99% )

Date/Time Setting

1. Press the [] button and hold until the Year number begin to flash, then release the button and press the [+]or[-] button to adjust the Year.
2. Press the [] button once, the Month number begin to flash, then press the [+]or[-] button to adjust the Month.
3. Press the [] button again, the day begin to flash, then press the [+]or[-] button to adjust the day.
4. Press the [] button, the hour begin to flash, then press the [+]or[-] button to adjust the hour.
5. Press the [] button, the minute begin to flash, then press the [+]or[-] button to adjust the minute.
6. After finish setting, press [] button to confirm or automatically save if no operation within 15s and return to time/day display.

12/24H Time Setting

1. Under normal using mode, press the [] button to switch 12/24H time format.
2. When the 12H time format is selected, the AM or PM will display on the screen.

Outdoor Device

1. Red indicator light 2. Wall hanging hole

3. Air flow Vent 4. Battery compartment

1. Power supply: 2*AAA battery
2. Waterproof and wall hanging design （Vents facing down）
3. Outdoor temperature measurement range: -40℃~60℃(-40℉~140℉)
4. Outdoor temperature lower than -40℃, LL is displayed Outdoor temperature higher than 60℃, HH is displayed
5. Humidity measurement range: 10%~99%
6. Temperature accuracy range: ± 1℃
7. Humidity accuracy range: ±5% RH

Battery Installation

1. Open the battery cover of the outdoor device, as shown in the figure below.
2. Put 2* AAA batteries according to the polarity marks, and close the battery cover.

Note：

1. Please do not mix old and new batteries to use.
2. If the battery is running low(voltage<2.7V), there will be a low battery icon on the indoor device display.
3. After the receiver is low in power, it will restart repeatedly/full display, please replace the battery

Connection between Indoor & Outdoor Device

1. After the indoor device is installed with the battery, the indoor device RF “” icon flashes for 3 minutes, indicating that the indoor device has entered the connection mode and is waiting for the outdoor device to connect.
2. After installing the battery on the outdoor device, wait a while the RF “” icon no longer flashes, or long press the [–] button for connection,and the temperature and humidity of the outdoor device are displayed on the indoor unit, which means that the connection is successful.

Clear the outdoor Device Value and Reconnect

If you want to reset the channel connection, press and hold the [-] button until the temperature and humidity of the outdoor device on the indoor device display “—-“, and then repeat the above setting operations to reset the connection.

Note: Every time when you replace the battery (indoor/ outdoor device) or the indoor/outdoor device loses connection, please be sure to Replace the indoor and outdoor device battery for pair and reconnect the device according to the above synchronization  process.

Note

1. The distance between the outdoor device and the Indoor device: a straight line distance of 330ft/100m in an open area, and the range would shorter based on interference present.
2. The indoor device should always be placed in a well-ventilated place, away from vents, heating or cooling elements, direct sunlight, windows, doors or any other openings.
3. The outdoor device can be placed on an indoor or outdoor plane and ensure that the outdoor device is within the transmission distance of the indoor device and has the least obstacles.
4. Both indoor and outdoor device can be installed on the wall.
5. External sensor vents are not waterproof, please keep the vents down to prevent the rain from damaging the sensor inside.

Tips
If the outdoor data display —- or replace the dead battery，please try the following steps:

1. Remove the battery of the outdoor and indoorthermometer.
2. Indoor thermometer: long press [-] button or re-install the battery(WiFi symbol flashing means connecting )
3. Re-install the battery of outdoor sensor（ the red signal indicator flashes means automatically connecting）

MAX & MIN Record of Temperature & Humidity

1. Press the [-] button once to display the highest indoor and outdoor temperature/humidity record with in  24Hrs since the last reset, and the display shows MAX.
2. Press the [-] button again to display the lowest indoor and outdoor temperature / humidity record within  24Hrs since the last reset. The display shows MIN.

Specification

Launch mode: ASK433MHZ
Firing period: CH1=57S

WARRANTY

60-Day Money-Back for Any Reason
You may return your undamaged product and packaging within 60 days of purchase to receive a full refund for any reason.
18-Month Warranty for Quality-Related Issue
Please kindly contact our customer service if you have quality-related issues, we will take care of quality-related issues with a replacement or full refund.

support@vocoovip.com

Documents / Resources

VOCOO 6202 Wireless Thermometer Indoor Outdoor Hygrometer [pdf] User Manual 6202 Wireless Thermometer Indoor Outdoor Hygrometer, 6202, Wireless Thermometer Indoor Outdoor Hygrometer, Thermometer Indoor Outdoor Hygrometer, Indoor Outdoor Hygrometer, Outdoor Hygrometer

References

• User Manual