V I C O STAND-V106A Hex Monitor Desk Mount Instruction Manual

Contents hide

1 V I C O STAND-V106A Hex Monitor Desk Mount

2 Product Usage Instructions

3 PACKAGE CONTENTS

4 ASSEMBLY STEPS

5 Documents / Resources

5.1 References

6 Related Posts

V I C O STAND-V106A Hex Monitor Desk Mount

Product Specifications

SKU: STAND-V106A

Weight Capacity: 22 lbs (10 kg) per arm

Product Usage Instructions

Tools Needed

Phillips screwdriver
Drill

Screwdriver

Package Contents

A (x1) Pole
B (x1) Clamp

C (x1) Clamp Brace
D (x1) Decorative Cover

E (x2) Center Monitor Arm
F (x4) Monitor Arm

G (x8) Plastic Spacer
H (x1) Support Plate

I (x1) Foam Pad
J (x4) Monitor Arm Cover

K (x4) Side VESA Plate
L (x2) Center VESA Plate

M (x8) Cable Clip
N (x1) Spare Cap

O (x1) Spare Arm Cover
S-A (x4) M10x47mm Screw

S-B (x1) M10x100mm Screw
S-C (x3) M6x10mm Screw

S-D (x2) M10x15mm Screws
S-E (x4) M8x10mm Screw

S-F (x4) Nut
S-G (x2) M4x6mm Screw

S-H (x1) Spring Washer
S-I (x1) M10 Washer
M-A (x24) M4x12 Thumbscrew
M-B (x24) M4x30mm Screw
M-C (x24) M4 Spacer
T-A (x1) 3mm Allen Wrench
T-B (x1) 5mm Allen Wrench
T-C (x1) 6mm Allen Wrench
T-D (x1) Wrench

Assembly Steps – Clamp Installation

Install Pole (A) to Clamp Brace (C) using M6x10mm Screws (S-C) and a Phillips screwdriver.
Assemble Clamp (B) to Clamp Brace (C) using M10x15mm Screws (S-D) and 6mm Allen Wrench (T-C). Secure the clamp assembly to the desktop by tightening the hand bolts on Clamp (B).
Install the Pole Cover (D) to Pole (A).

Assembly Steps – Grommet Installation

Remove adhesive backing from Foam Pad (I) and place it on the bottom of Pole (A).
Install Pole (A) to an existing grommet hole using Support Plate (H), M10x100mm Screw (S-B), M10 Washer (S-I), and Spring Washer (S-H). Tighten with Wrench (T-D).
Install the Pole Cover (D) to Pole (A).

Assembly Steps – Arm Assembly

Lay Monitor Arms (F) on a flat surface with holes for cable clips facing down. Add Plastic Spacers (G) to the holes at the ends of Monitor Arms (F).
Align Monitor Arms and Center Monitor Arms (E, F) so that the holes for the cable clips are facing down. Insert Monitor Arms (F) into Center Monitor Arms (F). Secure using M10x47mm Screws (S-A) and 6mm Allen Wrench (T-C).

Press Monitor Arm Covers (J) onto the top and bottom of arm joints. Place Cable Clips (M) into wire clip holes.

Assembly Steps – Mounting
Slide the arm assembly onto Pole (A) at the desired height and secure using M8x10mm Screws (S-E) and 5mm Allen Wrench (T-B).

FAQ

Q: What is the weight capacity of this desk mount?
A: The weight capacity of this desk mount is 22 lbs (10 kg) per arm.
Q: Are there any age restrictions for using this product?
A: Yes, this product is not suitable for children under 3 years old. Adult supervision is required.
Q: What tools are needed for assembly?
A: You will need a Phillips screwdriver, a drill, and a screwdriver.

Q: Can I exceed the weight capacity of this desk mount?
A: No, it is important not to exceed the weight capacity as it may result in serious injury.

Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product.
https://vivo-us.com/products/stand-v106a
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
Email: help@vivo-us.com
Website: www.vivo-us.com
Chat live with an agent!
Tel: 309-278-5303

WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.

USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

DO NOT EXCEED WEIGHT CAPACITY. Failure to do so may result in serious injury.

TOOLS NEEDED

PACKAGE CONTENTS

ASSEMBLY STEPS

STEP 1 – Clamp Installation
Install Pole (A) to Clamp Brace (C) using M6x10mm Screws (S-C) and a Phillips screwdriver.

Assemble Clamp (B) to Clamp Brace (C) using M10x15mm Screws (S-D) and 6mm Allen Wrench (T-C). Secure the clamp assembly to the desktop be tightening to the hand bolts on Clamp (B). Install the Pole Cover (D) to Pole (A).

STEP 1 – Grommet Installation
Remove adhesive backing from Foam Pad Pad (I) and place on the bottom of Pole (A).

Install Pole (A) to existing grommet hole using Support Plate (H) with M10x100mm Screw (S-B), M10 Washer (S-I) and Spring Washer (S-H). Tighten with Wrench (T-D). Install the Pole Cover (D) to Pole (A).

If no grommet hole exists, drill a 3/8” (10mm) diameter hole through the mounting surface.

STEP 2
Lay Monitor Arms (F) on flat surface with holes for cable clips facing down. Add Plastic Spacers (G) to holes at ends of Monitor Arms (F).

NOTE: Transparent monitor arm image used to show cable clip holes. Holes are on the underside of arms and are not visable when arm is facing upright.
Align Monitor Arms and Center Monitor Arms (E,F) so that the holes for the cable clips are facing down. Insert Monitor Arms (F) into Center Monitor Arms (F) as shown below. Secure using M10x47mm Screws (S-A) and 6mm Allen Wrench (T-C).

NOTE: Transparent monitor arm image used to show wire clip holes. Holes are on the underside of arms and are not visable when arm is facing upright.
Press Monitor Arm Covers (J) onto the top and bottom of arm joints. Place Cable Clips (M) into wire clip holes.

STEP 3
Slide arm assembly onto Pole (A) at desired height and secure using M8x10mm Screws (S-E) and 5mm Allen Wrench (T-B).

STEP 4a – Flat Back Monitors
Attach the Center VESA Plates (L) to the monitors you intend to mount in the center of the mount. Attach Side VESA Plates (K) to remaining monitors. Secure using M4x12mm Screws (M-A).

Center VESA Plate (L) Installation

Side VESA Plate (K) Installation
NOTE: Hand tighten screws to avoid stripping the plastic screw heads.

STEP 5
Slide the center monitor onto the center mount of arm assemblies. Install M4x6mm Screws (S-G) to secure the monitor.

STEP 6
Slide the outer monitors onto the outer mounting heads. Secure with Nut (S-F).

Adjust Monitor Height
To adjust center monitor height, turn the screw behind center mounts using the 5mm Allen Wrench (T-B).

To level the side monitors, remove the Nut (S-F) and turn the inner bolt with the 3mm Allen Wrench (T-A) to raise or lower the monitor. Replace Nut after the adjustment.

To adjust swivel joint tension, remove monitor arm covers and turn the bolt underneath with the 6mm Allen Wrench (T-C).

Adjust Monitor Tilt
Pry off Plastic Covers (F2) from the Outer VESA Heads (F1). The exposed nut on the side is used to adjust the tilt. Tighten the nut using Wrench (T-D) to adjust. Replace Plastic Covers (F2).

To adjust center monitor swivel or tilt, use 3mm Allen Wrench (T-A) to loosen center set screw on the center mounting heads, as shown at left.

Cable Management
Manage cables using Cable Clips (M) on assembled arms. Remove the split cap from the Pole (A) and feed cables through, pulling ends out from the opening in back. Replace the split cap when finished.

Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us
Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

Tel: 309-278-5303
AVG. RESOLUTION TIME (within office hrs): 5M 4S
Website: www.vivo-us.com

Chat live with an agent!
AVG. RESOLUTION TIME (within office hrs): < 15 M
Email: help@vivo-us.com

AVG. RESPONSE TIME (within office hrs): 1HR 8M

23% within < 15m
38% within < 30m

61% within < 1hr
83% within < 2hr
92% within < 3hr

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

Documents / Resources

V I C O STAND-V106A Hex Monitor Desk Mount [pdf] Instruction Manual
STAND-V106A Hex Monitor Desk Mount, STAND-V106A, Hex Monitor Desk Mount, Monitor Desk Mount, Desk Mount, Mount