MOUNTUP MU0006 Triple Monitor Stand Mount
WARNING!
If you have any confusions or are not quite sure about the installation, please do not hesitate to ask for our help. Before assembly, please check and make sure all necessary accessories are included and undamaged. Improper installation, such as use the product for monitors over its load capacity or for any purpose not explicitly specied, may cause damage or serious injury. We would not be liable for any damage or injury caused by improper mounting or inappropriate use. The kit contains small items that could be choking hazards if swallowed. Please keep them OUT OF REACH OF CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
DO NOT EXCEED WEIGHT CAPACITY.
ASSEMBLY STEPS
STEP 1: Clamp Installation OR Grommet Base Installation
Firstly mount Bace (C) to Pole (B) using Bolts (P). Tighten them using 4mm Allen Key (R).
OPTION A: Clamp Installation
Mount Bracket (E) to Base (C) with Bolts (O). Bolts could be tightened by the 4mm Allen Key (R). Apply pads (Q) to the bottom of Base (C) to avoid desk scratches.
Attach Clamp (F) to Bracket (E) with Bolts (O) and 4mm Allen Key (R). Adjust the Clamp width to t with desk.
Secure stand to desktop by tightening Clamp (F) . Attach Base Support Cover (G) to Bracket (E).
OPTION B: Grommet Base Installation
Place Carriage Bolt (I) through the center of Grommet Base (K). Mount Grommet Base to Base (C) bottom with Bolts (O) and tighten them by 4mm Allen Key (R). Apply pads (Q) to the bottom of Base (C) to avoid desk scratches.
Run Carriage Bolt (I) through grommet hole on desktop. Attach Support Plate (J) and Wingnut (L). At last, tighten Wingnut (L).
STEP 2 : Arm Installation
Install the middle head (H) wire clip(N) and swivel arm (A) to the pole (B). Fasten the bolt with supplied 6mm Allen key (T)
WARNING:
For your safety, do not move the stand off your desk!
STEP 3: Attach Monitor
OPTION A: Flat Back Monitor
Attach the VESA plate (D) to the back of monitor and secure it by using a 6 mm Allen Key (T) to tighten screws (M-A).
Do not tighten the screws excessively or your monitor might be damaged.
NOTE: If the M-A screw is a little long, please use a H5mm spacer to x it.
OPTION B: Curved Back Monitor
Attach the VESA plate (D) to the back of monitor and secure it by using a 6 mm Allen Key (T) to tighten screws (M-B) along with spacers (M-C). 
Do not tighten the screws excessively or your monitor might be damaged.
STEP 4: Hang Monitor
Slide the monitors onto the head of swivel arm.Install the security bolt (M). Make sure the security bolt is installed before you rotate the monitor.
Guideline to adjust monitor tilting angle.
STEP 5 : Adjust Tension
For intended functioning of the mount, you may need to adjust the tension of Upper Arm (A) in accordance with your monitor weight by 6 mm Allen Key (T).
NOTE: If the bolt is covered over, please hold the upper arm and press it down to maintain a horizontal position, and then you can see the adjustment screw at the joint. Be sure to keep the arm in a horizontal position during adjustment.
Note: For how many circles the screw should be turned, please refer to the table below.
STEP 6 : Cable Management
Remove bottom plastic covers from gas spring arm (A) .Run cables from monitor through bottom of arm. Reattach plastic covers as shown in diagram. Store Allen keys (S,T) in wire clip (N) for future use.
Adjust as Desired
Adjust monitor position and rotation.
- Tilt
- Swivel
- Rotation
- Height
Note: To ensure stability, the tightness of the rotating axis has been preset, so it would be kind of difficult to rotate the VESA plate.
Suggestion: Please attach the monitor first, then hold the two sides of it with both hands, and rotate vigorously. If that doesn’t work out, please do not hesitate to ask for our help.
Product Dimensions
CAUTION AND MAINTENANCE:
- Don’t allow children to climb, stand, hang, or play on any part of monitor or stand.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
- Check that the bracket is secure and safe to use at regular intervals (at least every three months).
Documents / Resources
 |
MOUNTUP MU0006 Triple Monitor Stand Mount [pdf] Instruction Manual MU0006 Triple Monitor Stand Mount, MU0006, Triple Monitor Stand Mount, Monitor Stand Mount, Stand Mount, Mount |
