DuroBumps-LGOO

DuroBumps DBR375 Toyota Land Cruiser 200 series Rear Bump Stops

DuroBumps-DBR375-Toyota-Land-Cruiser-200-series-Rear-Bump-Stops-PRODUCT

Product Information

  • Specifications:
    • Part Number: DBR375
    • Product Name: Rear Bump Stops
    • Includes:
      • (2) Two rear DuroBumps
      • (4) Four JIS 10.9 M8-1.25 40mm flange bolts with pre-applied thread locker
      • (1) One FREE sticker

Product Usage Instructions

  • Step 1: Prepare Vehicle
    • Following vehicle manufacturer recommendations, use a properly rated jack. Lift the rear of the truck with the floor jack and support the frame rails with jack stands. Remove the rear wheels. Be sure to use jack stands!
  • Step 2: Remove OEM Bump Stops
    • Remove the OEM bump stop located on the frame rail above the rear axle tube, using a 12 mm deep socket. There are 2 bolts for each bump stop.
  • Step 3: Clean Frame
    • Use a scraper or wire brush to clean any mud/debris from the frame.
  • Step 4: Install DuroBumps
    • Mount the DuroBumps bump stop in the OEM location on the frame rail. Insert the bolts into the factory holes. Tighten the bolts using a 12mm socket wrench until snug. Do not over-tighten.
  • Step 5: Finalize Installation
    • Reinstall the wheels and lower the vehicle back to the ground. Torque the lug nuts to factory specifications.
    • Now go hit some trails or cruise the mall … whatever you’re into!

FAQs

  • Q: Can these rear bump stops be used on any vehicle?
    • A: These bump stops are designed for specific vehicle models, so it is recommended to check compatibility before installation.
  • Q: Do I need any special tools to install these bump stops?
    • A: Basic tools such as a jack, jack stands, socket wrench, and scraper are required for installation.

What’s included

  • (2) Two rear DuroBumps
  • (4) Four JIS 10.9 M8-1.25 40mm flange bolts with pre-applied thread locker
  • (1) One FREE sticker

Tools Required

  • Jack and jack stands
  • 12mm deep socket wrench
  • Lug nut socket or wrench
  • Scraper or wire brush to clean debris
  • Torque wrench

Instructions

  • Step 1: Following vehicle manufacturer recommendations, use a properly rated jack. Lift the rear of the truck with the floor jack and support the frame rails with jack stands. Remove the rear wheels. Be sure to use jack stands!
  • Step 2: Remove the OEM bump stop located on the frame rail above the rear axle tube, using a 12 mm deep socket. There are 2 bolts for each bump stop.
  • Step 3: Use a scraper or wire brush to clean any mud/debris from the frame.
  • Step 4: Mount the DuroBumps bump stop in the OEM location on the frame rail. Insert the bolts into the factory holes. Tighten the bolts using a 12mm socket wrench until snug. Do not over-tighten.
  • Step 5: Repeat steps 2 – 4 on the other side of the vehicle.
  • Step 6: Reinstall the wheels and lower the vehicle back to the ground. Torque the lug nuts to factory specifications.

Now go hit some trails or cruise the mall … whatever you’re into! www.DuroBumps.com .

  • Part# DBR375 – Rear Bump Stops

Documents / Resources

DuroBumps DBR375 Toyota Land Cruiser 200 series Rear Bump Stops [pdf] Instruction Manual
DBR375 Toyota Land Cruiser 200 series Rear Bump Stops, DBR375, Toyota Land Cruiser 200 series Rear Bump Stops, Cruiser 200 series Rear Bump Stops, Rear Bump Stops, Bump Stops

References

Leave a comment

Your email address will not be published. Required fields are marked *