Ford RACING M-7195-C4 C-4 Deep Sump Cast Aluminum Oil Pan
Product Information
Specifications
- Part Number: M-7195-C4
- Material: Cast Aluminum
- Includes: Deep cast aluminum oil pan, drain plug, drain plug washer, socket head cap screws 5/16-18 x 3/4, lock washers
- Required Filter Kit: Ford Motor Company service number D0DZ-7A098-C, Hughes Performance part number HP-5285, WIX part number 58933, ATP part number B-51
Installation Instructions
- Raise and properly support your vehicle with jack stands. Refer to your owner’s manual for correct jacking points.
- Place a drain pan under the transmission oil pan. Loosen all pan attaching bolts to within a few turns of removal. Carefully break the gasket seal to allow the fluid to drain.
- Once most of the fluid has drained, remove the pan and let the remaining fluid drain into the drain pan.
- Remove the oil filter.
- Install a new filter and torque it to 80-100 in. lbs.
- Clean the transmission flange surface with a safe solvent and allow it to dry.
- Place the new gasket on the cast pan and then install the pan with the supplied hardware. Torque the bolts to 12-16 ft.-lbs.
- Add three quarts of recommended transmission fluid as specified in the owner’s manual. Additional fluid will be required after starting the vehicle.
- Lower the vehicle.
- Start the engine and move the gear selector through the shift pattern.
- Check the fluid level according to the owner’s manual.
FAQ
- Where can I find the Ford shop manuals?
Factory Ford shop manuals are available from Helm Publications. You can contact them at 1-800-782-4356. - What should I do if I don’t understand the installation instructions?
If you have any difficulties understanding the instructions, please call the Ford Racing Techline at 1-800-367-3788 for assistance. - Can I complete the installation myself?
If you are not confident in your ability to complete the installation safely, it is recommended to have a certified technician perform the installation to avoid any damage to your vehicle.
Caution: If you are not confident that you can complete the installation safely, have it completed by a certified technician! Failure to complete the installation correctly could cause damage to your vehicle.
PARTS IN KIT
REQUIRED FILTER KIT
- Ford Motor Company service number D0DZ-7A098-C
- Hughes Performance (1-800-274-RACE) part number HP-5285
- WIX part number 58933
- ATP part number B-51
INSTALLATION INSTRUCTIONS
- STEP 1: Raise and properly support your vehicle with jack stands. See your owners’ manual for correct jacking points.
- STEP 2: Place drain pan under transmission oil pan. Loosen all pan attaching bolts to within a few turns of removal. Carefully break the gasket seal allowing the fluid to drain.
- STEP 3: When most of the fluid has drained, remove the pan and allow the balance of the fluid to drain into the drain pan.
- STEP 4: Remove oil filter.
- STEP 5: Install new filter; torque to 80-100 in. lbs.
- STEP 6: Clean transmission flange surface with safe solvent. Allow to dry.
- STEP 7: Place new gasket on cast pan, then install pan with supplied hardware and torque to 12-16 ft.-lbs.
- STEP 8: Add three quarts of recommended transmission fluid; see owners’ manual. Additional fluid will be required after starting vehicle.
- STEP 9: Lower vehicle.
- STEP 10: Start engine and move gear selector through the shift pattern.
- STEP 11: Check fluid level per owners’ manual.
FOR MORE INFO
- Factory Ford shop manuals are available from Helm Publications, 1-800-782-4356
- Please visit www.fordracingparts.com for the most current instruction information
Documents / Resources
 |
Ford RACING M-7195-C4 C-4 Deep Sump Cast Aluminum Oil Pan [pdf] Instruction Manual M-7195-C4 C-4 Deep Sump Cast Aluminum Oil Pan, M-7195-C4 C-4, Deep Sump Cast Aluminum Oil Pan, Cast Aluminum Oil Pan, Aluminum Oil Pan, Oil Pan, Pan |
References
-
Official Site of Ford Performance Parts - Mustang Parts, Crate Engines, Packs, Wheels, Superchargers, Racing Parts | Performance Parts Authority
-
Manual-Hub.com – Free PDF manuals!
- User Manual
