RUSTA 901513180101 Silence Vacuum Cleaner
Specification
| Voltage | 220 –240 V ~ 50–60 Hz |
| Power | 700W |
| Suction power | 200W |
| Dimensions | 460 x 310 x 255 mm |
| Telescopic tube | 58–90 cm |
| Range | 12 m |
| Weight | 8.7 kg |
| Cord length | 9 m |
| Noise level | 69 dB(A) |
| Bag capacity | 4 l |
| Vacuum cleaner bag | 1900 |
| Filter / | HEPA 12 |
| Protection class | II |
Instruction
GET STARTED!
- Remove all components from the packaging.
- Connect the hose to the main body of the cleaner, ensuring it locks into position. (Fig. 1) To release the hose: rotate the connector counterclockwise and pull it. (Fig. 2)
- Connect the other end of the tube to the carpet and floor nozzle. (Fig. 3)
USE
- Pull the power cord out and plug it into the power supply. Do not pull the cord beyond the red marker. (Fig. 4)
- Adjust the telescopic tube to the desired height by moving the telescopic tube adjuster and raising or lowering the tube to the most comfortable cleaning position. (Fig. 5)
- The floor nozzle is ideal for cleaning for various floor types. Brushes are lowered
to protect the floor. - Switch the cleaner on by pressing the on/off pedal on the main body of the cleaner. (Fig. 6)
- Adjust the power level by pressing the variable power control button or by sliding the variable power control slider. (Fig. 7)
- Adjust the suction regulator to the desired level.
- Switch off after use by pressing the on/off pedal. Unplug and retract the power cord back into the cleaner.
CARE AND CLEANING
EMPTYING THE DUST CONTAINER
If the bag check indicator is red please check and, if necessary, replace the bag.
- Lift the bag door release latch to open the bag door, pull the bag holder and pull the collar of the bag to remove it. (Fig. 8)
- Apply the peel and seal sticker located on the bag collar to the bag inlet.
The full dust bag should be disposed of correctly and carefully. (Fig. 11) - Fold a new bag as shown on the bag and fit by inserting the collar into the bag holder.
- Refit the bag holder and close the bag door.
WARNING! The bag door will NOT close if the dust bag and/ or the bag holder are not properly assembled on the cleaner. Always ensure the bag and bag holder are present when closing the bag door.
REMEMBER! The bag check indicator LED may also be lit if an obstruction has occurred. In this case refer to “Removing a blockage from the system”.
CLEANING THE FILTER
To maintain optimum performance of your cleaner, please wash the filters after each 5 bag changes.
CLEANING THE PRE-MOTOR FILTER
- Lift the bag door release latch to open the bag door and remove the bag holder. (Fig. 8)
- Remove the pre-motor filter frame from the cleaner. (Fig. 12)
- Remove the filter sponge from the holder. (Fig. 13)
- Wash it in hand warm water, and allow it to dry thoroughly before replacing it in the cleaner. (Fig. 17, 18)
CLEANING THE EXHAUST FILTER AND EXHAUST SPONGE
- To remove the exhaust sponge and the exhaust filter, remove exhaust sponge 1 from the exhaust cover and unclip the filter pack and remove the other sponge 2.(Fig. 14, 15, 16)
- Wash them in hand warm water and allow them to dry thoroughly before replacing. (Fig. 17, 18)
REMEMBER! Do not use hot water or detergents. In the unlikely event the filters become damaged, new filters will need to be fitted. Do not try and use the product without a dust bag or filter fitted.
CLEANING THE PERMANENT CLOTH DUST BAG
To maintain optimum performance, we recommended that you wash the permanent cloth dust bag under warm water after every 5 full bags. Remove excess water and leave to dry fully before replacing.
REMOVING A BLOCKAGE FROM THE SYSTEM
If the bag check indicator LED is illuminated or flashing:
- Check if the bag is full. If so refer to “Replacing the dust bag”.
- If it is not full, then:
- Do the filters need cleaning? If so refer to “Cleaning the filter”.
- Check if there is any other blockage in the system – Use a cord or a pole to remove any blockage from the telescopic tube or flexible hose.
WARNING! The bag check indicator LED will turn on if the cleaner is used when full, if there is a blockage or if the filters are dirty. If the cleaner is used for a significant period of time with the bag check indicator LED on, a thermal cut out will switch the cleaner off to prevent overheating.
The bag check indicator LED turns off once the cleaner has switched off to signal that the thermal cut out has been activated. If this should happen, switch the cleaner off, unplug and correct the fault. It will take about 30 minutes for the cut out to automatically reset.
TROUBLESHOOTING
Should you have a problem with the product, complete this simple user checklist before calling your local service.
- Is there a working electricity supply to the cleaner? Please check with another electrical appliance.
- Is the dust bag over-filled? Please refer to “Care and cleaning”.
- Is the filter blocked? Please refer to “Cleaning the filter”.
SAFETY INSTRUCTIONS
When using an electrical appliance, you should always take basic safety measures. Always keep the following in mind:
- Read all instructions.
- If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
- The product may be used by children of 8 years and older and by persons with reduced physical, sensory or mental capability or lack of experience and knowledge provided they have been given supervision or instruction concerning use of the product in a safe way and understand the hazards involved.
- Children should be supervised to ensure that they do not play with the appliance.
- For the first operation, it is advisable to read the manual carefully before hand and keep it properly for future use.
- Before the first operation, make sure the dust cup or the dust bag is properly installed.
- Make sure the power supply is 220–240 V~, 50–60 Hz.
- Do not vacuum water and flammable material.
- Do not vacuum burning materials and/or ashes.
- Do not use the machine without a motor protection filter.
- Please change the dust bag immediately if it is damaged
or worn out. - Failure to empty the dust bag and/or clean the filters may result in overheating of the appliance and cause damage to the motor. Therefore, it should be considered as a priority to ensure that these are properly maintained.
- Do not store or use the machine close to high temperature places.
- If abnormal noise, smell, smoke or any other failure or breakage is found during the operation, you should turn off the switch and unplug it. Then contact with your service center for repair. Do not repair by yourself.
- The plug must be removed from the power socket before any maintenance or replacement.
- The product must only be used indoors and only as described in this instruction manual.
- Only use accessories that are recommended by the manufacturer or retailer.
- Never immerse the product in water.
- Do not leave the product in direct sunlight for long periods.
- Never use the product for vacuuming construction site waste such as cement, gypsum, or concrete dust.
- Unplug the product when it is not in use.
- Save these instructions.
WARNING!
If these instructions are not followed, an accident may lead to serious personal injury or property damage.
ENVIRONMENT AND RECYCLING
When the product is used up, leave it for recycling according to local waste disposal regulations. Note that the product must not be disposed of with normal household waste.
RIGHT OF COMPLAINT
By law the product must be returned to the place of purchase along with the original receipt in the event of a complaint. The user is liable for any damage to the product that is caused by not using the product for its intended purpose or by not following this user manual correctly. The right of complaint will not apply in these instances.
Documents / Resources
 |
RUSTA 901513180101 Silence Vacuum Cleaner [pdf] Specifications 901513180101 Silence Vacuum Cleaner, 901513180101, Silence Vacuum Cleaner, Vacuum Cleaner, Cleaner |
