Contents hide
1 V I V O STAND-LAP1F Aluminum Laptop Floor Stand
2 PACKAGE CONTENTS
3 ASSEMBLY STEPS
4 OPTION B: Tablet Holder
5 Documents / Resources
5.1 References

V I V O-LOGO

V I V O STAND-LAP1F Aluminum Laptop Floor Stand

V I V O-STAND-LAP1F-Aluminum-Laptop-Floor-Stand-PRODUCT

WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
NOTE: SOME PARTS INCLUDED MAY NOT BE USED DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.

TIPOVER WARNING

  • SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER
  • NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF THE STAND
  • USE TIP-OVER RESTRAINT OR ANCHOR STAND TO WALL
  • THE USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

PACKAGE CONTENTS

V I V O-STAND-LAP1F-Aluminum-Laptop-Floor-Stand-FIG- (1)

NOTE

  • SOME PARTS INCLUDED MAY NOT BE USED
  • DO NOT EXCEED WEIGHT CAPACITY.V I V O-STAND-LAP1F-Aluminum-Laptop-Floor-Stand-FIG- (2)
  • Failure to do so may result in serious injury.

TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

  • NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF THE STAND
  • USE TIP-OVER RESTRAINT OR ANCHOR STAND TO WALL
  • THE USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

ASSEMBLY STEPS

STEP 1
Assemble the Left Foot (B) to the Base (A) using M6x10mm Bolts (S-A). Tighten with the 4mm Allen Wrench (T-A).
V I V O-STAND-LAP1F-Aluminum-Laptop-Floor-Stand-FIG- (3)

STEP 2
Insert the threaded side of Pole (C) into the base assembly, making sure the slot is facing towards the back. Secure the pole using the M10x25mm Bolt (S-B) and the 6mm Allen Wrench (T-A).

V I V O-STAND-LAP1F-Aluminum-Laptop-Floor-Stand-FIG- (4)

STEP 2 (Continued)
Tighten the rear set screw using the 4mm Allen Wrench (T-A).

V I V O-STAND-LAP1F-Aluminum-Laptop-Floor-Stand-FIG- (5)

STEP 3
Slide the Arm (D) onto Pole (C), loosening the thumbscrew first if needed. Press the Pole Cap (E) into the top of Pole (C). Tighten thumbscrew at desired height for Arm (D).
V I V O-STAND-LAP1F-Aluminum-Laptop-Floor-Stand-FIG- (6)

STEP 4

V I V O-STAND-LAP1F-Aluminum-Laptop-Floor-Stand-FIG- (7)V I V O-STAND-LAP1F-Aluminum-Laptop-Floor-Stand-FIG- (8)
OPTION A
Laptop TrayRemove the pre-installed bolt and white plastic spacer from the Laptop Hinge (F) using the 5mm Allen Wrench (T-A). Insert the hinge swivel joint into the top of the Arm (D), making sure the tabs in the black plastic bushing fit into the slots in the hole. Secure using the previously removed spacer and bolt with the 5mm Allen Wrench (T-A). Slide the Laptop Tray (I) into the Laptop Hinge (F) until the latch engages. Adjust the tilt joint if necessary using the 5mm Allen Wrench (T-A), then pull out on the sides of the tray and place the laptop computer into the tray.

STEP 4 (Continued)

V I V O-STAND-LAP1F-Aluminum-Laptop-Floor-Stand-FIG- (9)V I V O-STAND-LAP1F-Aluminum-Laptop-Floor-Stand-FIG- (10)

OPTION B: Tablet Holder

Remove the bolt and white plastic spacer from the Tablet Hinge (G) using the 5mm Allen Wrench (TA). Insert the hinge swivel joint into the top of the Arm (D), making sure the tabs in the black plastic
bushing fit into the slots in the hole. Secure using the previously removed spacer and bolt with the Allen Wrench (T-A). Install the Tablet Holder (H) using the M5x16mm Bolt (S-C) with the 4mm Allen Wrench (T-A). Adjust the tilt joint if necessary using the 4mm Allen Wrench (T-A), then pull out the holder clips and place the tablet into the Tablet Holder (H).

Adjust as Desired
V I V O-STAND-LAP1F-Aluminum-Laptop-Floor-Stand-FIG- (11)
Love your new VIVO setup and want to share?
Tag us in your photo! vivo_us

Open Monday – Friday 7:00 am – 7:00 pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product. FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

Documents / Resources

V I V O STAND-LAP1F Aluminum Laptop Floor Stand [pdf] Instruction Manual
STAND-LAP1F, STAND-LAP1F Aluminum Laptop Floor Stand, Aluminum Laptop Floor Stand, Laptop Floor Stand, Floor Stand, Stand

References

Leave a comment

Your email address will not be published. Required fields are marked *