FREEDOM MICRO ® II HS MANUAL
ATTACHING SMARTCABLE™
- Insert SmartCable into the charge port on the puck. The hooks on the cable should click when fully seated.
Phone should be turned ON, and unlocked before inserting SmartCable™ while in MTI Connect® mode. - Plug SmartCable into the charge port of the device.
REMOVING SMART CABLE
- Insert the crescent end of the Freedom Micro II tool into the opening to the right of the LED. Twist the Freedom Micro II tool clockwise 45 degrees and hold it in place.
- Twist the device and bracket off of the position.
- Remove the SmartCable from the puck.
- The loose cable can be clipped into SpeedBracket™ for easy storage.
RFID COMMANDS
Default Mode
Enter Standard Mode
Program User Card
Exit Programming Mode
Arm/Disarm Position
Set Lockdown/Unlock While Armed
Tap and Hold Access Card for 10 seconds. It will double beep immediately, and double beep again after 10 seconds. The position will automatically lockdown when armed, and unlock when disarmed when in Lockdown mode.
RFID MTI CONNECT PAIRING
Default Mode
Enable Pairing Mode on MTI Connect Hub
|
Enter Network Mode |
||
 |
 |
 |
LED STATUS INDICATORS
|
Visual Reference |
System Status |
Condition |
 |
Solid White | Puck is armed and docked. |
 |
Single white flash every 5 seconds | Puck is armed and lifted. |
|
Double white flash every 8 seconds | Puck is docked, but not armed, the puck is connected to a mesh network. |
 |
Flashing Red and White with an audible alarm | Flashing Red and White with audible alarm Alarm has been triggered. silence the alarm and inspect the tether, puck trigger, and base trigger. |
|
Flashing Red and White with no audible alarm | Puck is in silent alarm mode. The audible alarm has exceeded 5 minutes and the position is unable re-arm itself. inspect the tether, puck trigger, and base trigger before attempting to arm the puck. |
 |
Solid Yellow | Puck is armed, docked, but has lost it’s a network connection. Ensure the puck is within range of the MTI Connect® Hub. Try network pairing again. *Only applicable when the puck is being used with the MTI Wireless Network. |
| Visual Reference | System Status |
Condition |
 |
Flashing Yellow Every 5 Seconds | Puck is armed and lifted, the puck is NOT connected to a mesh network. Only applicable in Network Mode. |
 |
Solid Blue | After tapping an authorization card: The puck is in enrollment mode. Tap VersaKey™ to authorize them for use in standard mode. Enrollment mode closes automatically in 3 minutes. In normal use: Overcurrent in charging circuit – most likely a problem in the SmartCable™. |
 |
Flashing Blue | Puck has entered network pairing mode. Stops upon successful pairing, or after 90 seconds. |
 |
Single Red Flash | TO BE VERIFIED: Only follows an attempt to arm the puck. Occurs when the puck cannot arm, for example, due to a released trigger but the user attempts to arm the puck with the app or key. |
 |
Multi-colored flash | Puck has received an “identify” command from a user of the MTI Connect® software. |
 |
Flashing Green | Puck is disarmed in factory default mode. Complete the setup for Standard or Network mode to use VersaKey™ or MTI Connect®. Note: The puck may automatically arm while in this default mode, as long as all triggers are closed for 15 minutes. Once its arms, the LED will turn solid white. |
RISER DIMENSIONS
PUCK DIMENSIONS
RISER WITH ADAPTER DIMENSIONS
BRACKET DIMENSIONS
FCC AND ISED STATEMENT
FCC ID: 2AA2X-15000282
Model: ROUND FREEDOM MICRO II HS
FCC Statement
This device complies with Part 15 of the FCC Rules.
Caution: If any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment.
The RF Exposure Compliance distance is 20 millimeters.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
ISED Certification Number: 24439-15000282
Model: ROUND FREEDOM MICRO II HS
ISED Statement
This device complies with Innovation, Science, and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
CAN ICES-3(B)/NMB-3(B)
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 millimeters between the radiator and your body.
Technical Data
| Operating Temperature: | 0°C to 40°C |
| Operating Frequency: | 2405 MHz to 2480 MHz |
| Max Power: | Less than 4 dBm at 2.4 GHz |
| Operating Frequency: | 125kHz |
| Max Power: | Less than 20 dBuA/m at 3m |
Additional Safety Information
- For indoor use only. The apparatus shall not be exposed to water.
- No user-replaceable parts inside; refer servicing to the manufacturer or qualified service personnel.
- Only use accessories specified by the manufacturer.
- Do not expose to excessive heat sources.
Disposal: All electrical and electronic products including batteries should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.
This product contains a rechargeable battery. Proper storage, use, and disposal of the battery are important. Please refer to the guidelines below:
- Properly dispose of the battery; Do not dispose of the battery in a furnace/oven or into a fire or mechanically crush or cut the battery, as this could cause the battery to explode.
- Storing the battery in an environment at higher temperatures than stated above can result in an explosion or leaking of flammable liquid or gas.
- Subjecting a battery to very low air pressure or high altitudes can result in an explosion or leaking of flammable liquid or gas.
www.MTIGS.com | T:800.426.6844
FREEDOM MICRO ® II HS MANUAL
Documents / Resources
 |
MTI Freedom Micro II HS Anti-Theft Security for Smartphones [pdf] Instruction Manual 15000282, 2AA2X-15000282, 2AA2X15000282, Freedom Micro II HS Anti-Theft Security for Smartphones, Freedom Micro II HS, Anti-Theft Security for Smartphones |
Smart Locks, Access Control, Retail Display Security | MTI 
