saunaLife LOGOModel G2 / G4
Led Lightbar SystemsaunaLife G2 Series LED Light Bar SystemSauna Led Light bar System

LED Lightbar Package Contents:

saunaLife G2 Series LED Light Bar System - Package Contents

Installation Recommendations

Please read this manual in its entirety prior to installation and keep it somewhere safe for future reference.
IMPORTANT
The RF Driver and Power Supply may be installed outdoors but must be protected from rain and snow. RF Driver and Power Supply should be installed in a waterproof electrical enclosure.
IMPORTANT
When installing the RF Driver and Power Supply inside the sauna, maintain a minimum distance of 20” from heat source and a maximum height of 20” off floor or in path of fan.
IMPORTANT
If installed inside the sauna, the RF Control must not exceed 131°F. Control should be no more than 3′ off the floor and away from heater. Test temperature reading of location before mounting.
IMPORTANT
Consider light placement carefully. Each fixture should be placed to avoid direct contact with the bathers eyes.
IMPORTANT
LED Light Bar max operating temperature is 195°F, installing LED light bar in location where temperature will exceed 195°F may cause light failure

Electrical Requirements

  • A 120V AC electrical outlet is needed to power the lighting system.
  • Your electrician will determine the type of electrical outlet, box, and piping to be used.
  • All wiring must be done in accordance with national electric code and local building codes by a certified electrician.
  • Improper voltage or connections will damage the components and void warranty.

STEP 1.
Mount RF Driver / Receiver
Using 2 screws mount RF driver to desired surface. Driver should be mounted in a dry accessible location for service.

saunaLife G2 Series LED Light Bar System - Receiver

STEP 2.
Connect 2-Pin 4-Way Cable
Locate 2-Pin 4-way cable and connect single end to 2-Pin Pigtail of Driver.

saunaLife G2 Series LED Light Bar System - 4 Way Cable

STEP 3.
Run 2-Pin 30’ Cable
Run 2-Pin 30’ light cable from Driver to LED light bar. At Driver connect to one of the 4 leads on 2-Pin 4-Way cable

saunaLife G2 Series LED Light Bar System - Cable

STEP 4.
Install Mounting Brackets & LED Light Bar
Determine the location where LED light will be installed. Screw Mounting Clips to surface ensuring even coverage of light fixture. Carefully snap LED light bar into each clip.

saunaLife G2 Series LED Light Bar System - LED Light Bar

STEP 5.
Connect 2-Pin 30’ Cable to Light Bar
Connect light cable end to lead off light bar.
Note: Repeat this step if installing more than one light.

saunaLife G2 Series LED Light Bar System - Cable to Light Bar

STEP 6.
Install Power Supply
Connect AC power cord cable to power supply block. Place power supply near RF driver. Connect DC cable end from power supply and connect into RF driver DC IN port.

saunaLife G2 Series LED Light Bar System - Power Supply

STEP 7.
Dimming Control Installation
RF Remote includes a wall mount holder for storing. Take holder and separate back mounting plate from holder. At mounting location screw mounting plate to surface. Slide holder from top down onto mounting the plate.

saunaLife G2 Series LED Light Bar System - Control Installation

STEP 8.
Startup & Testing

  • Verify that all connections are secure and complete before proceeding.
  • Ensure DC-out end of Power Supply is plugged into DC-in of the Driver.
  • Plug AC power cable from the Power Supply into a 120V AC electrical outlet.
  • Verify that the Driver powers on. The indicator light will flash purple rapidly for approximately 20 seconds.

STEP 9.
RF Driver & Dimming Remote Programming
Note: RF Driver is preprogrammed. Follow steps below if programming is needed.

  1. Press and hold the Match button until the Run Indicator light changes to white.
    Note: The Run indicator will turn off, then rapidly flash purple. White run indicator will be after Blue.
  2. Release the Match button, then short press once to save programming.
  3. Grab remote then on Driver press match button once then quickly press the power button on remote.

Control Operation

Follow the steps below for control operation. After 30 seconds of inactivity the remote will enter sleep mode. To wake up the control, press any button.

saunaLife G2 Series LED Light Bar System - Control Operation

saunaLife G2 Series LED Light Bar System - Symbol 1 Wi-Fi Setup

saunaLife G2 Series LED Light Bar System - Symbol 2 On IOS or Android download the Tuya Smart App
To set up Wi-Fi operation follow the steps below
Note: Wi-Fi Driver supports 802.11 b / g / n 2.4 GHz Wi-Fi standard. The Wi-Fi Driver
Step 1
Open Tuya app and press Sign Up to create an account

saunaLife G2 Series LED Light Bar System - Wi Fi Setup 1

Step 2
Enter an email address to register an account

saunaLife G2 Series LED Light Bar System - Wi Fi Setup 2

Step 3
Check email and enter verification code

saunaLife G2 Series LED Light Bar System - Wi Fi Setup 3

Step 4
Create a password

saunaLife G2 Series LED Light Bar System - Wi Fi Setup 4

Step 5
Main screen press Add Device

saunaLife G2 Series LED Light Bar System - Wi Fi Setup 5

Step 6
Press Add next to Discovering Devices

saunaLife G2 Series LED Light Bar System - Wi Fi Setup 6

Step 7
Select your Wi-Fi network

saunaLife G2 Series LED Light Bar System - Wi Fi Setup 7

Step 9
Device added successfully, press done to complete setup

saunaLife G2 Series LED Light Bar System - Wi Fi Setup 8

Specifications

RF Driver/Receiver

Operating Voltage: 24V DC
Rated Out Current: 5CH, 3A/CH
Output Voltage: 12-24V DC
Max Output Power: 5Ch X 72W
Operating Temp: -22°F – 131°F
Dimensions: 4.48”L x 1.49”W x .78”H
Light Capacity: 4 Lights / 20’ (per Driver)IP20
IP Rating: IP20
Certifications: CE. EMC, LVD, RED

RF Remote Single-Zone Dimming

Output Signal: RF (2.4GHz)
Operating Voltage: 3V DC (CR2032)
Power Consumption: 5mA
Dimming Range: 1% – 100%
Signal Distance: 98FT
Dimensions: 5.47”L x 1.41”W x .43”H
Operating Temp: -22°F – 131°F
Zones: 1 Zone Single Color
IP Rating: IP20
Certifications: CE, EMC, LVD, RED

Power Supply

Input Voltage: 120V AC
Output Voltage: 24V DC
Rated Power: 90W
AC Current: 1.3A
DC Current: 3.75A
Operating Temp: -22°F – 158°F
IP Rating: IP20
Certifications: UL, CE, FCC
LED Light Bar Specifications
Kelvin: 3500k Operating Temp: -13°F to 195°F Max Run: 4 Light Bars / 20 Linear Feet IP Rating: IP67
Part Number Operating Voltage (VDC) Max Wattage Lumens Dimensions (with flush clips) Dimensions (with adjustable clips)
G2 BP031086 LED White 24V DC 14.27W 1,571 3/4W x 9/16H x 60L 3/4W x 1-1/4H x 60L
G4 BP031158 LED White 24V DC 18.69W 2,059 3/4W x 9/16H x 76L 3/4W x 1-1/4H x 76L

Troubleshooting

No Power

  • Verify that the electrical outlet has voltage.
  • Check that connections on Power Supply are securely connected.
  • Check that the DC barrel plug on the Power Supply is securely connected.

Power but light’s not turning on

  • Check that the Pigtail cable from the Driver is securely connected and that wiring is correct (see step #1).
  • Check that 4-way light cable is secure and connected.
  • Check that all 30’ cables to lights are securely connected.
  • Verify each light functions by testing them directly to the Driver independently.
    Note: To test individual light, disconnect 4-way light cable and connect 30’ cable directly to Pigtail lead oĀff Driver, or connect light directly Pigtail.
  • Verify that RF Remote is paired with Driver, see page #7.

Lights on with no function from Control

  • Verify battery is inserted correctly.
  • Low battery, replace with new battery.
  • Check DC power cable from Driver to Control is securely connected.
  • Ensure that the distance from the Remote to the Driver is not more than 98 feet. If so, relocate Driver closer to room.

Resetting Driver
The Driver should not need to be reset in normal conditions. If a reset is needed, follow the steps below.

  • Verify power to Driver
  • Press and hold the Match button for 10-15 seconds until the blue LED indicator flashes rapidly.
    Note: Resetting Driver will clear any paired remotes and require repairing.

Replacement Parts 

Description Part Number
Driver BP031108
Power Supply/90W BP031137
RF Control Single-Zone White BP031111
4-Way IP67 2-PIN Splitter BP031075
2-PIN IP67 Pigtail BP031073
2-PIN IP67 30′ Cable BP031077
60” White Light Bar BP031086
76” White Light Bar BP031158

Notes:
…………………….

saunaLife LOGOTechnical Support
(224) 253-5909
© 2023 Bathing Brands, Inc.
REV: 1.1_1/2024

Documents / Resources

saunaLife G2 Series LED Light Bar System [pdf] User Manual
G2, G2 Series LED Light Bar System, Series LED Light Bar System, LED Light Bar System, Light Bar System, Bar System, G4

References

Leave a comment

Your email address will not be published. Required fields are marked *