LITETRONICS PST Series Standard DLC LED Back Lit Panel Instruction Manual

Safety Instructions and Warnings
When using electrical equipment, basic safety precautions should always be observed. Read the instructions carefully before installing the fixture. Retain these instructions for future reference.

Product Usage Instructions

Turn off the power at the electrical panel.
Remove the ceiling tile or existing fixture from the grid ceiling space.

Before installing, locate the grid clips on your panel; bend them up and out so they can rest on top of the grid.
Unscrew and remove the driver cover to access the input, ground, and dimming wires.

Locate the adjustable wattage and CCT slide switch on the top of the driver and set it to the desired wattage. Refer to the slide switch settings below.
Tilt and raise the panel up into the empty grid space, then lower it until the grid clips catch on the tee-grid bar. Attach the panel to the building with support wires (not included) using the hole in the grid clip.

Remove one conduit knock-out from the driver cover, then run the branch power wire from the conduit to the driver cover.
Follow the wiring diagram (Figure 1) for proper connections:
- Connect the green ground line through the conduit with a wire nut.
- Connect the neutral (white) line to the wire labeled AC-N with a white wire nut.
- Connect the live power (black) line to the wire labeled AC-L with a black wire nut.
- If 0-10V dimming is required, connect incoming dimming lines to the DIM+ (Purple) and DIM- (Gray/Pink) wires. Follow the dimmer manufacturer’s instructions.

Close the driver cover and secure it with the screw.
Replace the ceiling tiles, turn on the power, and your installation is complete.

Product Overview

LED Driver

CCT Slide Switch
Grid Clips

Wattage Slide Switch
AC-L and AC-N dimming and ground wires
Conduit knockouts
LED Back Lit Panel
Tee-grid bar

CCT Slide Switch Settings

5000K
4000K
3500K

Note: CCT default setting is set to 4000K.

Wattage Slide Switch Settings – 1′ x 4′ & 2′ x 2′

Note: Watts default setting is set to 40W.

Wattage Slide Switch Settings – 2′ x 4′

Note: Watts default setting is set to 50W.

For any further inquiries or updated instructions, please contact us at 800-860-3392 or via email at customerservice@litetronics.com. You can also visit our website at www.litetronics.com.

PRODUCT OVERVIEW

WHAT COMES IN THE BOX

LED Back Lit Panel

Wire Nut (x3)
Installation Instructions

TOOLS NEEDED

Wire Stripper

Wire Cutter
Phillips Screwdriver

SAFETY INSTRUCTIONS AND WARNINGS

WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE OBSERVED.

READ CAREFULLY BEFORE INSTALLING THE FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Litetronics fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Risk of fire or electric shock. LED Back Panel installation requires knowledge of luminaire electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
Be certain electrical power is OFF before and during installation and maintenance.

LED Back Panel must be connected to a wiring system with an equipment–ground conductor.
Make sure the supply voltage is the same as the rated luminaire voltage.
Only the open holes indicated in the photographs and/or drawings may be made or altered as a result of this kit installation. Do not leave any other open holes in an enclosure of wiring or electrical components.

To prevent wiring damage or abrasion, do not expose wiring to the edges of sheet metal or sharp objects.
There are no user-serviceable parts inside of the LED Back Lit Panel.
Suitable for damp locations.

Suitable for 9/16” or 15/16” Flat Tee grids in both insulated ceilings and non-insulated ceilings. Access above the ceiling is required.
The vapor barrier must be suitable for 90º C.
Fixture to be independently supported to the building structure.

INSTALLATION PROCEDURE

READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION

Turn off the power at the electrical panel.
Remove the ceiling tile or existing fixture from the grid ceiling space.

Before installing, locate the grid clips on your panel; bend them up and out so they can rest on top of the grid.
Unscrew and remove the driver cover to access the input, ground, and dimming wires.
Locate the adjustable wattage and CCT slide switch on the top of the driver and set to the desired wattage. See slide switch settings below.

Tilt and raise the panel up into the empty grid space, then lower it until the grid clips catch on the tee-grid bar. Attach the panel to the building with support wires (not included) using the hole in the grid clip.
Remove one conduit knock-out from the driver cover, then run the branch power wire from the conduit to the driver cover.
Follow the wiring diagram, in Figure 1.
- a. Connect the green ground line through the conduit with the wire nut.
  b. Connect the neutral (white) line to a wire labeled AC-N with a (white) wire nut.
  c. Connect the live power (black) line to a wire labeled AC-L with a (black) wire nut.
  d. If 0 -10V dimming is required, connect incoming dimming lines to the DIM+ (Purple) and DIM- (Gray/Pink) wires. Follow the dimmer manufacturer’s instructions.
Close the driver cover and secure it with the screw.
Replace the ceiling tiles, turn on the power and your installation is complete.

WIRING DIAGRAM

SETTINGS

CCT SLIDE SWITCH SETTINGS

5000K

4000K

3500K

Note: CCT default setting set to 4000K.

WATTS SLIDE SWITCH SETTINGS 1’ X 4’ & 2’ X 2’

25W

30W

40W

Note: Watts default setting is set to 40W.

WATTS SLIDE SWITCH SETTINGS 2’ X 4’

30W

40W

50W

Note: Watts default setting is set to 50W.

Contact Information

6969 W. 73rd Street Bedford Park, IL 60638
WWW.LITETRONICS.COM

CustomerService@Litetronics.com
1-800-860-3392

The information and product specifications contained in these instructions are based upon data believed to be accurate at the time of printing. This information is subject to change without notice and without incurring liability. If you have questions regarding specific product details, please contact us at 800-860-3392 or via email at customerservice@litetronics.com.

To check for an updated version of these instructions, please visit www.litetronics.com.

Documents / Resources

LITETRONICS PST Series Standard DLC LED Back Lit Panel [pdf] Instruction Manual
PST Series Standard DLC LED Back Lit Panel, PST Series, Standard DLC LED Back Lit Panel, LED Back Lit Panel, Back Lit Panel, Lit Panel, Panel

LITETRONICS PST Series Standard DLC LED Back Lit Panel Instruction Manual

LITETRONICS PST Series Standard DLC LED Back Lit Panel

Product Information