PRESIDENT Jerry II Mobile CB Radio Owner's Manual

Antenna Installation:
- Remove the flexible antenna (C2) from the device.
- Connect the CB antenna to the mobile charge module (C3).
- Clip the mobile charge module (C3) to the bottom of the unit.

Choosing Your Antenna:
- For CB radios, longer antennas provide better results.
- Install the mobile antenna in an area with maximum metallic surface away from windscreen mountings.
- If you have a radio-telephone antenna, ensure the CB antenna is higher.

Adjustment of SWR (Standing Wave Ratio):
- Must be done when using the CB radio for the first time and whenever re-positioning the antenna.
- Connect an external SWR-meter between the CB radio and the antenna.

Frequently Asked Questions

Q: What should I do before using the CB radio?
- A: Before use, ensure to connect the flexible antenna (C2) or a CB antenna with SWR set. Failure to do so may damage the power amplifier.
Q: Can I use two antennas simultaneously?
- A: No, using two antennas together can destroy the device.
Q: Where can I find information about different frequencies?
- A: Refer to pages 28 to 33 for details on European frequencies covered by the flexible antenna (C2).

“`

View Fullscreen

JERRY
Portable or Mobile CB Radio
Owner’s manual

Contents:

details may differ C3

C6
Manual
C1 JERRY C2 Flexible antenna S-20 C3 Mobile charge module C4 Battery pack 1800 mA (Lithium Ion) C5 Fuse C6 Owner’s manual
2

Your PRESIDENT JERRY at a glance
3

SUMMARY
MOBILE CONFIGURATION PORTABLE CONFIGURATION CONTROLS AND FUNCTIONS FUNCTION DESCRIPTION MENU SETTING FUNCTION TURNING ON THE UNIT FUNCTION WITH PTT SWITCH CHARGING THE JERRY TECHNICAL CHARACTERISTICS TROUBLE SHOOTING HOW TO TRANSMIT OR RECEIVE A MESSAGE GLOSSARY SIMPLIFIED DECLARATION OF CONFORMITY GENERAL WARRANTY CONDITIONS FREQUENCY TABLES F – NORMS

English
6 8 8 9 15 20 20 20 21 22 23 23 34 26 28 ~ 33 34

English

WARNING!
Before using, be careful never to transmit without first having connected the flexible antenna (C2), or, with a CB antenna*, without having set the SWR (Standing Wave Ratio) ! Failure to do so may result in destruction of the power amplifier, which is not covered by the warranty. The flexible antenna (C2) covers all European frequencies (see tables pages 28 to 33).
*When the flexible antenna (C2) has been removed and replaced by a CB antenna using the Mobile Charger Module (C3).
Never use two antennas together, otherwise the device may be destroyed.
MULTI-NORMS TRANSCEIVER!
See function “F” on page 20 and the Configuration table on page 34.
The warranty of this transceiver is valid only in the country of purchase.
5

English

Welcome to the world of the new generation of CB radios. The new PRESIDENT range gives you access to top performance CB equipment. With the use of up-to-date technology, which guarantees unprecedented quality, your PRESIDENT JERRY is a new step in personal communication and is the surest choice for the most demanding of professional CB radio users. To ensure that you make the most of all its capacities, we advise you to read carefully this manual before installing and using your PRESIDENT JERRY.
A) MOBILE CONFIGURATION
1) ANTENNA INSTALLATION
– Remove the flexible antenna (C2) from the device. – Connect the CB antenna to the mobile charge module (C3). – Clip the mobile charge module (C3) to the bottom of the unit in
any side. a) Choosing your antenna – For CB radios, the longer the antenna, the better its results. Your
dealer will be able to help you with your choice of antenna. b) Mobile antenna – Must be fixed to the vehicle where there is a maximum of metallic
surface (ground plane), away from windscreen mountings. – If you already have a radio-telephone antenna installed, the CB
antenna should be higher than this. – There are two types of antenna: pre-regulated which should be
used on a good ground plane (e.g. car roof or lid of the boot), and adjustable which offer a much larger range and can be used on a smaller ground plane (see § 3, ADJUSTMENT OF SWR). – For an antenna which must be fixed by drilling, you will need a good contact between the antenna and the ground plane. To obtain this, you should lightly scratch the surface where the screw and tightening star are to be placed. – Be careful not to pinch or flatten the coaxial cable (as this runs the risk of break down and/or short-circuiting). – Connect the antenna to the mobile charge module (C3).
6

English

OUTPUT RADIUS PATTERN
c) Fixed antenna – A fixed antenna should be installed in a clear space as possible. If
it is fixed to a mast, it will perhaps be necessary to stay it, according to the laws in force (you should seek professional advice). All PRESIDENT antennas and accessories are designed to give maximum efficiency to each CB radio within the range.
2) BASIC OPERATIONS TO BE CARRIED OUT BEFORE USING YOUR SET FOR THE FIRST TIME (without transmitting and without using the «push-to-talk» switch)
a) Check the antenna connections. b) Turn the set on by turning the Power knob (1) clockwise. c) Set the squelch OFF. d) Adjust the volume to a comfortable level. e) Go to channel 20 by using the channel selectors s or t key (3).
3) ADJUSTMENT OF SWR (Standing wave ratio)
WARNING: This must be carried out when you use your CB radio for the first time (and whenever you re-position your antenna). The adjustment must be carried out in an obstacle-free area.
* Adjustment with external SWR-meter (e.g. TOS-1 PRESIDENT)
a) To connect the SWR meter : – Connect the SWR meter between the CB radio and the antenna
as close as possible to the CB (use a maximum of 15.75 inches / 40 cm, type President CA-2C).
b) To adjust the SWR meter: – Set the CB on channel 20. – Put the switch on the SWR-meter to position FWD (calibration). – Press the «push-to-talk» switch on the microphone to transmit.
7

English

– Bring the index needle to t by using the calibration key. – Change the switch to position REF (reading of the SWR level).
The reading on the Meter should be as near as possible to 1. If this is not the case, re-adjust your antenna to obtain a reading as close as possible to 1. (An SWR reading between 1 and 1.8 is acceptable). – It will be necessary to re-calibrate the SWR meter after each adjustment of the antenna.
WARNING: In order to avoid any losses and attenuations in cables used for connection between the radio and its accessories, PRESIDENT recommends to use a cable with a length less than to 118.11 inches / 3 m.
Your CB is now ready for use.

B) PORTABLE CONFIGURATION

INSTALLATION

Screw the flexible antenna (C2) on the device. – Check that the battery is fully charged. See § CHARGING THE
JERRY page 20.
Your CB is now ready for use.

C) CONTROLS AND FUNCTIONS

C2 Flexible antenna A External microphone plug B External speaker plug C Internal microphone D Internal speaker E Battery Pack Door

1 On/Off – Volume 2 LCD 3 UP s / DOWN t Keys

key – MENU key

5 SCAN key – DW (Dual Watch) key

6 EMG (Emergency) key – VOX key

7 F key

8 MON (Monitor) key

9 ANL/NB/ Compander – HI-CUT key

10 MODE key

11 SQ- (Squelch -) key

12 SQ+ (Squelch +) key

English

13 HI/LO (High/LOW) transmitting power key 14 PTT (Push To Talk) switch 15 FLASHLIGHT 16 LED Rx and TX
D) FUNCTION DESCRIPTION 1) ON/OFF ~ VOLUME
– Turn the On/Off-Volume knob (1) clockwise for setting the unit on and increase the volume. If the KEY BEEP function is activated, 4 tones sound when you turn the CB radio on.
– Turn the On/Off-Volume knob (1) counter clockwise for decreasing the volume and setting the unit off. See § KEY BEEP on page 15. See ECO MODE page 16
2) DISPLAY
9

English

FM/AM/UK
MON
BP ANL NB HIC
SCAN VOX DW EMG

Mode FM or AM. UK in FM, U configuration only ASC activated Monitor activated Roger Beep activated Function Key Beep activated ANL filter activated NB filter activated HI-CUT filter activated Compander filter activated Noise Gate activated Function SCAN activated Function VOX activated Function DW (Dual Watch) activated Emergency channel activated Function LOCK is activated
Battery Level
Charging indicator
Menu activated
Indicates Configuration or Vox parameter
Indicates Frequency or Menu

TX or RX bargarph
3) CHANNEL SELECTOR: t/s keys
– Press the t (3) key to decrease a channel. – Press the s (3) key to increase a channel.
A «beep» sounds each time the channel changes if the KEY BEEP function is activated. See § KEY BEEP page 15.
4) ~ MENU

(short press)
– Turn on the unit.
– Long press the key (4) to switch on the flashlight. – Quickly press the s or t key (3) to select between the 4 possible
lights :

English

– Long press the key (4) to switch off the flashlight.
MENU (long press)
1. Long press the MENU key (4) to enter the MENU. appears on the display.
2. Press the s or t key (3) to select the menu to be set. 3. Short press the MENU key (4) to validate the selected menu. The
parameter of the menu blinks. 4. Press the s or t key (3) to change the parameter. 5. Press the MENU key (4). A short press to validate and stay in the
MENU or a long press to validate and exit the MENU. 6. If no key is pressed, the unit exits the MENU after 10 seconds
without saving the modifications. See § MENU SETTING page 15.
5) SCAN ~ DW ~ SKIP SCAN (short press)
Short press the SCAN key (5) to activate the SCAN function. Press the s key (3) to scan in increasing order. Press the t key (3) to scan in decreasing order. The scanning stops as soon as there is a busy channel. The scanning automatically starts 3 seconds after the end of the transmission and no key is activated during 3 s. The scan also restarts in increasing order with the s key (3), or in decreasing order with the t key (3). When the SCAN function is activated, “SCAN” blinks on the display. In the current mode, press the PTT switch (14) to deactivate the SCAN function. “SCAN” disappears on the display.
DW (Dual Watch) (long press)
Long press the DW key (5) to activate the DW function. Allows to alternate between the active and a second (customizable) channel. When the function is active, “DW” appears on the display. Press the PTT switch (14) to exit the DW function. See menu DW (Dual Watch) SETTING page 18.
11

English

SKIP (long press only when the SCAN function is activated)
This function allows you to skip a channel found by the SCAN function. When scanning stops on an unwanted channel, press and hold the SCAN key (5) for 1 second to save that channel in the SCAN SKIP memory. A beep is emitted, it will no longer be scanned. See § SCAN page 11.
See SCAN SKIP menu page 19 and RESET menu page 19.
6) EMG ~ VOX EMG (short press)
Emergency channel is automatically selected when by pressing EMG Key (6). First short press to call the first emergency customisable channel. Second short press to call the second emergency customisable channel. “EMG” appears on the display when an emergency channel is activated. Third short press to go back to the current channel. “EMG” disappears on the display. See § EMERGENCY SETTING page 17. See § KEY LOCK page 15.
VOX (long press)
The VOX function allows transmitting by speaking into the original microphone (or in the optional vox microphone) without pressing the PTT switch (14). The use of an optional vox microphone connected to the unit (A) disables the original microphone. Press shortly the VOX key (6) in order to activate the VOX function. «VOX» appears on the display. A new press on the VOX (6) key disables the function, «VOX» disappears. See menu VOX SETTING page 17.
7) F – FREQUENCY BAND SELECTION (short press)
See FUNCTION TURNING ON THE UNIT page 20. See § COMPANDER page 13.
8) MONITOR (short press)
This function allows to monitor the channel despite the squelch. When the is active or when the level of the manual squelch is high, press the MON key (8) to hear the active channel. See § KEY LOCK page 15.
12

English

9) ANL/NB ~ HI-CUT ~ COMPANDER ANL/NB (short press)
Short press the ANL/NB key (9) to activate/deactivate the filters in this order :
The activated filter is shown on the display. ANL – Automatic Noise Limiter: This filter allows the reduction of background noises and some reception interferences. In AM mode only. NB – Noise Blanker: This filter allows the reduction of back ground noise, and some reception interference.
HI-CUT (long press)
Long press the HI-CUT key (9) to activate/deactivate the HI-CUT filter. “HIC” appears on the display when the filter is active. Hi-Cut: Eliminates high frequency interferences. Has to be used in accordance with the reception conditions.
COMPANDER
– Press the F key (7) . is displayed. – Press the ANL/NB key (9) to activate/deactivate the compander.
When the COMPANDER is active appears on the LCD. This switchable filter allow to improve the reception mode.
10) MODE MODE (short press)
This key allows you to select the modulation mode (AM or FM). Your modulation mode has to correspond to the one of your correspondent. Corresponding mode is displayed on the LCD. – Amplitude Modulation / AM: communication on a field with relief and obstacles at middle distance (the most used). – Frequency Modulation / FM: for nearby communications on a flat open field. In U configuration ONLY: press MODE key (10) to alternate the frequency band between ENG and CEPT. “UK” appears in the display when the ENG band is selected. “UK” disappears from the display when CEPT is selected (see table at page 28).
13

English

11) MANUAL SQUELCH- (short press)
Short press the SQ- key (11) to decrease the level of the manual squelch.

12) MANUAL SQUELCH+ (short press)

Short press the SQ+ key (12) to increase the level of the manual squelch.

Manual squelch of:

or 34 levels from

11 + 12 ) ASC (Automatic Squelch Control)

Worldwide patent, a PRESIDENT exclusivity ASC suppresses undesirable background noises when there is no communication. Squelch does not affect neither sound nor transmission power, but allows a considerable improvement in listening comfort.

Press simultaneously the SQ- (11) and SQ+ (12) keys to activate/

deactivate the ASC function.

appears on the display when

the function is active. No repetitive manual adjustment and a

permanent improvement between the sensitivity and the listening

comfort when ASC is active.

13) HI/LO TRANSMITTING POWER (short press)
Short press the HI/LO key (13) to alternate between high and low transmitting power. “H” or “L” is displayed to indicate the selected level. See ECO MODE page 16.

14) PTT SWITCH

Transmitting mode (PTT switch pressed)
Press the PTT switch (14) to transmit. The LED (16) lights up red. Receiving mode (PTT switch released)
The LED (16) lights up green in receiving mode. You can hear the signal on the speaker. The bargraph indicates the emission (RF) or reception (S) level.

TOT (Time Out Timer)
If the transmission key is longer than 3 minutes, active channel start blinking, the transmission ends. The time-out tone will sound until the PTT switch (14) is released.

English

15) FLASHLIGHT
See § page 10.
16) LED
See § PTT SWITCH page 14.
6 + 8) KEY LOCK (EMG + MON keys)
Long press simultaneously the EMG (6) and MON (8) keys to activate/deactivate the KEY LOCK function. When the function is active, ” ” appears on the display.

MENU SETTING

See § MENU page 11.

1) ROGER BEEP
The Roger Beep sounds when the PTT switch (14) is released in order to let your correspondent speak. Historically as transceiver is a “simplex” communication mode, it is not possible to speak and to listen at the same time (as it is the case with a telephone). Once someone had finished talking, he said “Roger” to let his correspondent know that it was his turn to talk. The word “Roger” has been replaced by a significant beep. Which is where the words “Roger beep” originate from. When the function is active, the icon appears on the display.

1. Long press the MENU key (4) to enter the MENU. appears on

the display.

2. Press the s or t key (3) to select the

menu.

3. Short press the MENU key (4) to validate. The current value blinks.

4. Press the s or t key (3) to deactivate OF, or select between the

6 melodies for the ROGER BEEP from 01 to 06

5. Press the MENU key (4). A short press to validate and stay in the

MENU or a long press to validate and exit the MENU.

6. If no key is pressed, the unit exits the MENU after 10 seconds

without saving the modifications.

Default value is OF.

2) KEY BEEP
When the function is activated, a beep sounds when a key is pressed, by changing the channel etc. “BP” appears on the display when the function is active.

English

1. Long press the MENU key (4) to enter the MENU. appears on

the display.

2. Press the s or t key (3) to select the

menu.

3. Short press the MENU key (4) to validate. The current value blinks.

4. Press the s or t key (3) to activate On or deactivate OF the KEY

BEEP function.

5. Press the MENU key (4). A short press to validate and stay in the

MENU or a long press to validate and exit the MENU.

6. If no key is pressed, the unit exits the MENU after 10 seconds

without saving the modifications.

Default value is On.

3) ECO MODE
This function allows to save your battery. The unit goes in standby mode, LCD backlit out, RX in standby*, etc.

1. Long press the MENU key (4) to enter the MENU. appears on

the display.

2. Press the s or t key (3) to select the

menu.

3. Short press the MENU key (4) to validate. The current value blinks.

4. Press the s or t key (3) to deactivate OF the ECO MODE func-

tion or select between the 3 levels 01 (Low), 02 (Middle) and 03

(High).

5. Press the MENU key (4). A short press to validate and stay in the

MENU or a long press to validate and exit the MENU.

6. If no key is pressed, the unit exits the MENU after 10 seconds

without saving the modifications.

Default value is 02 (Middle).

*Level 01: 250 ms RX active / 250 ms RX inactive *Level 02: 250 ms RX active / 500 ms RX inactive *Level 03: 250 ms RX active / 1 s RX inactive

Note: If level 03 is selected, the transmitting power automatically changes to L (low). The H (high) power remains available but will be reseted to L if the device is switched off and then on again.

See HI/LO TRANSMITTING POWER page14.

4) TONE
This function allows to adjust the reception tone.

1. Long press the MENU key (4) to enter the MENU. appears on

the display.

2. Press the s or t key (3) to select the

menu.

English

3. Short press the MENU key (4) to validate. The current value blinks. 4. Press the s or t key (3) to select between the 11 levels from -5
to 5. 5. Press the MENU key (4). A short press to validate and stay in the
MENU or a long press to validate and exit the MENU. 6. If no key is pressed, the unit exits the MENU after 10 seconds
without saving the modifications.
Default value is 0.

5) EMG SETTING
This function allows to customise both emergency channels.

1. Long press the MENU key (4) to enter the MENU. appears on

the display.

2. Press the s or t key (3) to select the

menu.

3. Short press the MENU key (4) to validate. The current order of the

emergency channels binks.

4. Press the s or t key (3) to change the emergency to be set, or…

5. Short press the MENU key (4) to validate. The current channel

blinks.

6. Press s or t key (3) to select the channel.

7. Short press the MENU key (4) to validate the channel. The mode

blinks: AM, FM or FM UK (in U configuration only).

8. Press s or t key (3) to select the mode.

9. Press the MENU key (4). A short press to validate and stay in the

MENU or a long press to validate and exit the MENU.

10. If no key is pressed, the unit exits the MENU after 10 seconds

without saving the modifications.

The default priority channels are channel 09 AM (1) and channel 19 AM (2) respectively.

6) VOX SETTING
Three parameters allow to adjust the VOX function: Sensitivity: / Anti-vox level: / Vox delay time: .

1. Long press the MENU key (4) to enter the MENU. appears on

the display.

2. Press the s or t key (3) to select the

menu.

3. Short press the MENU key (4) to validate. The current parameter

binks ( , or ).

4a. Short press again the MENU key (4) to validate the parameter to

be set. The value of the parameter blinks or…

4b. Press s or t key (3) to select the next parameter. Short press the

MENU key (4) to validate.

English

5. Press the s or t key (3) to modify the value of the parameter. 6. Short press the MENU key (4) to validate. The current value of the
parameter stops blinking. The parameter is stored. 7. Repeat point 4 to 6 to adjust other parameters. 8. When all adjustments are done, press the MENU key (4). A short
press to validate and stay in the MENU or a long press to validate and exit the MENU. If the KEY BEEP function is activated, a long beep sounds to confirm the success of the operation (see § KEY BEEP page 15).
9. If no key is pressed, the unit exits the MENU after 10 seconds without saving the modifications.
Sensitivity : allows the adjustment of the microphone (original one or optional vox) for an optimum transmission quality. Adjustable level from 01 (high level) to 09 (low level). Default value: 02.
– Anti-Vox : allows disabling the transmission generated by the surrounding noise. The level is adjustable. OF (according the squelch level) and from 00 (without anti-vox) to 09 (low level). Default value: OF.
– Delay time : allows avoiding the sudden cut of the transmission by adding a delay at the end of speaking. The level is adjustable from 01 (short delay) to 09 (long delay). Default value: 01.
VOX SETTING doesn’t activate the VOX function.

7) DW (Dual Watch) SETTING
This function allows to customise the second channel scanned by the DUAL WATCH function.

1. Long press the MENU key (4) to enter the MENU. appears on

the display.

2. Press the s or t key (3) to select the

menu.

3. Short press the MENU key (4) to validate. The channel blinks.

4. Press the s or t key (3) to select the new channel to be watch.

5. Short press the MENU key (4) to validate the channel. The mode

blinks: AM, FM or FM UK (in U configuration only).

6. Press the s or t key (3) to select the mode.

7. Press the MENU key (4). A short press to validate and stay in the

MENU or a long press to validate and exit the MENU.

8. If no key is pressed, the unit exits the MENU after 10 seconds

without saving the modifications.

Default Dual Watch channel is channel 09.

English

SCAN SKIP

This function is used to store/delete in the SCAN SKIP memory.

1. Select the channel.

2. Long press the MENU key (4) to access the MENUS. appears

in the display.

3. Use the s/t keys (3) to select the menu

4. Press the MENU key (4). The current setting flashes in the display.

5. Use the s/t keys (3) to alternate between On and OF.

6. Press the MENU key (4) again to validate the choice. The value

stops flashing.

7. If no key is pressed, the device exits the MENUS after 10 seconds,

disappears from the display.

On: The channel is stored on the SCAN SKIP memory. When a channel is memorized, flashes alternately with the frequency band. Of: clears the channel from the SCAN SKIP memory. disappears from the display.

See § SKIP page 12.

9) RESET

This function allows you to clear the SCAN SKIP memory or restore all factory settings.

1. Long press the MENU key (4) to access the MENUS. appears

in the display.

2. Press the s or t key (3) to select the menu

3. Press the MENU key (4) to validate. flashes.

4. Use the s/t buttons (3) to alternate between and

5. Press the MENU key (4) to confirm. The device exits the MENUS.

disappears from the display.

6. If no key is pressed, the device exits the MENUS after 10 seconds,

disappears from the display.

empties the SCAN SKIP memory. All the channels are now accessible by the SCAN function (see § SKIP page12).

restores all factory settings.

English

FUNCTION TURNING ON THE UNIT

1) F – FREQUENCY BAND SELECTION
(Configuration: EU ; PL ; d ; EC ; U ; In) The frequency bands must be chosen according to the country where you are going to operate. Do not use another configuration. Some countries require user’s licence. See the table on page 35. How to proceed: – Switch off the transceiver – Turn on the power while pressing the F (7) key. The letter corresponding to the configuration is blinking. – In order to change the configuration, use the sor t key (3). – When the configuration is selected, long press on the F (7) key. The letter corresponding to the configuration is continuously displayed. At this stage, confirm the selection by switching off then switching on again the transceiver. See tables on page 28 ~ 33.
G) FUNCTION WITH PTT SWITCH
1) NOISE GATE (PTT + F)
– Press and hold the PTT switch (14). – Short press the F key (7) to activate (On) or deactivate (OF) the
NOISE GATE. ” ” is displayed when the function is active. Noise Gate: Prevents amplification of background noise. This results in optimized signal levels.
H) CHARGING THE JERRY

1) USING THE MOBILE CHARGE MODULE
1. Clip the mobile charge module (C3) to the bottom of the unit in any side.
2. Plug the cigar lighter plug of the mobile charge module (C3) into your vehicle.

– The charge begins. appears on the display to indicate charging

mode and indicates the charging level.

–

disappears when the unit is fully charged.

English

3) CHANGING BATTERY PACK
The battery pack is pre-installed in the unit. If you need to replace the battery pack : 1. Unscrew the battery pack door (E). If necessary, remove the belt clip (C4) or the standard microphone support (C3) to reach the screw. 2. Disconnect and remove the old battery pack. 3. Connect the new battery pack. 4. Screw then battery pack door (E).
Note: The battery pack is provided uncharged, so you must charge the battery pack before using it with the transceiver.

4) LOW BATTERY FEATURES
When the battery is uncharged the RX/TX LED (16) blinks yellow. A continuous beep sounds in TX mode. blinks on the display.

I) TECHNICAL CHARACTERISTICS

1) GENERAL – Channels – Modulation modes – Frequency ranges – Antenna impedance – Power supply
– Dimensions
– Weight

inches mm

– Accessories supplied
2) TRANSMISSION
– Frequency allowance – Carrier power – Transmission interference – Audio response – Emitted power in the adj.
channel – Microphone sensitivity – Drain – Modulated signal distortion

: 40 : AM/FM : from 26.965 to 27.405 MHz : 50 ohms : 13.2 V (mobile configuration)
7.4 V (portable configuration) : 5.98 (H) x 2.62 (W) x 1.46 (D) : 152 (H) x 66.5 (W) x 37 (D) : 0.67 lb with battery, without
antenna 305 g with battery, without antenna : See page 2
: +/- 200 Hz : 4 W AM / 4 W FM : inferior to 4 nW (- 54 dBm) : 300 Hz to 3 KHz
: inferior to 20 µW : 7 mV : 1,8 A max. : 2%

English

3) RECEPTION – Maxi. sensitivity at 20 dB sinad
– Frequency response – Adjacent channel selectivity – Maximum audio power – Squelch sensitivity
– Frequency image rejection rate
– Intermediate frequency rejection rate
– Drain – Internal speaker

: AM: 0.5 µV – 113 dBm FM: 0.3 µV – 116 dBm
: 300 Hz to 3 kHz : 60 dB : 1W : min: 0.2 µV – 120 dBm
max: 1 mV – 47 dBm
: 60 dB
: 70 dB : See ECO MODE page 16 : 16 ohms, 1 W

TROUBLESHOOTING

1) YOUR CB RADIO WILL NOT TRANSMIT OR YOUR TRANSMISSION IS OF POOR QUALITY
– Check that the antenna is correctly connected. – Check that the SWR is properly adjusted (Mobile Configuration
only). – Check that the programmed configuration is the correct one
(see table page 34).
2) YOUR CB RADIO WILL NOT RECEIVE OR RECEPTION IS POOR
– Check that the squelch level is properly adjusted. – Check that the programmed configuration is the correct one
(see table page 34). – Check that the volume is set to a comfortable listening level. – Check that the antenna is correctly connected and that the
SWR is properly adjusted (Mobile configuration only). – You are using the same modulation mode than your correspond-
ent.
3) YOUR CB WILL NOT LIGHT UP
– Check the battery or power supply. – Check the fuse (Mobile Configuration only).

English

K) HOW TO TRANSMIT OR RECEIVE A MESSAGE

Now that you have read the manual, make sure that your CB Radio is ready for use (i.e. check that your antenna is connected). Choose your channel (19, 27). Press the «push-to-talk» switch (14) and announce your message «Attention stations, transmission testing» which will allow you to check the clearness and the power of your signal. Release the switch and wait for a reply. You should receive a reply like, «Strong and clear». If you use a calling channel (19, 27) and you have established communication with someone, it is common practice to choose another available channel so as not to block the calling channel.

L) GLOSSARY

Below you will find some of the most frequently used CB radio expressions. Remember this is meant for fun and that you are by no means obliged to use them. In an emergency, you should be as clear as possible.

INTERNATIONAL PHONETIC ALPHABET

A Alpha B Bravo C Charlie D Delta E Echo F Foxtrot G Golf

H Hotel

O Oscar

I India

P Papa

J Juliet

Q Quebec

K Kilo

R Romeo

L Lima

S Sierra

M Mike

T Tango

N November U Uniform

V Victor W Whiskey X X-ray Y Yankee Z Zulu

TECHNICAL VOCABULARY

AM CB CH CW DX DW FM GMT HF

: Amplitude Modulation : Citizen’s Band : Channel : Continuous Wave : Long Distance Liaison : Dual Watch : Frequency Modulation : Greenwich Meantime : High Frequency

English

LF LSB RX SSB SWR SWL SW TX UHF USB VHF

: Low Frequency : Lower Side Band : Receiver : Single Side Band : Standing Wave Ratio : Short Wave Listening : Short Wave : CB Transceiver : Ultra High Frequency : Upper Side Band : Very High Frequency

CB LANGUAGE

Advertising

: Flashing lights of police car

Back off

: Slow down

Basement

: Channel 1

Base station

: A CB set in fixed location

Bear

: Policeman

Bear bite

: Speeding fine

Bear cage

: Police station

Big slab

: Motorway

Big 10-4

: Absolutely

Bleeding

: Signal from an adjacent chan-

nel interfering with the transmis-

sion

Blocking the channel

: Pressing the PTT switch without

talking

Blue boys

: Police

Break

: Used to ask permission to join a

conversation

Breaker

: A CBer wishing to join a channel

Clean and green

: Clear of police

Cleaner channel

: Channel with less interference

Coming in loud and proud : Good reception

Doughnut

: Tyre

Down and gone

: Turning CB off

Down one

: Go to a lower channel

Do you copy?

: Understand?

English

: Long distance

Eighty eights

: Love and kisses

Eye ball

: CBers meeting together

Good buddy

: Fellow CBer

Hammer

: Accelerator

Handle

: CBer’s nickname

Harvey wall banger

: Dangerous driver

How am I hitting you?

: How are you receiving me?

Keying the mike

: Pressing the PTT switch without

talking

Kojac with a kodak

: Police radar

Land line

: Telephone

Lunch box

: CB set

Man with a gun

: Police radar

Mayday

: SOS

Meat wagon

: Ambulance

Midnight shopper

: Thief

Modulation

: Conversation

Negative copy

: No reply

Over your shoulder

: Right behind you

Part your hair

: Behave yourself – police ahead

Pull your hammer back : Slow down

Rat race

: Congested traffic

Rubberbander

: New CBer

Sail boat fuel

: Wind

Smokey dozing

: Parked police car

Smokey with a camera : Police radar

Spaghetti bowl

: Interchange

Stinger

: Antenna

Turkey

: Dumb CBer

Up one

: Go up one channel

Wall to wall

: All over/everywhere

What am I putting to you? : Please give me an S-meter

reading.

English

GENERAL WARRANTY CONDITIONS

This device is guaranteed 2 years parts and labour in its country of purchase against any manufacturing defects validated by our technical department. *The After-sales Service of PRESIDENT reserves the right not to apply the warranty if a breakdown is caused by an antenna other than those distributed by PRESIDENT, and if said antenna is at the origin of the breakdown. An extension of 3 years warranty is proposed systematically for the simultaneous purchase of a device and an external mobile PRESIDENT antenna (this does not include the flexible antenna S-20 (C2) for the JERRY unit), bringing the total duration of the warranty to 5 years. In order to be valid, the warranty certificate must be returned within a period of 30 days after the purchase date to the After-sales Service of the company Groupe President Electronics, or any foreign subsidiary. It is recommended to carefully read the following conditions and to respect them under penalty of losing their benefit. · To be valid the warranty certificate must be returned to us at the latest 1 month after
the purchase. · Please duly complete the warranty certificate on the right hand side of the page,
detach it (portion to be removed marked by dotted line) and send it back. · Any repair under warranty will be free and the return delivery costs will be borne
by our company. · A purchase proof must be necessarily included with the device to be repaired. · The dates listed on the warranty certificate and proof of purchase must match. · Do not proceed with the installation of the device without reading the user manual. · No spare part will be sent nor exchanged by our services under warranty. The warranty is only valid in the country of purchase.
Exclusions (are not covered): · Damages caused by accident, shock or inadequate packaging. · Batteries, power transistors, microphones, lights, fuses and the non respect of the
installation and use of specifications (including but not limited to antenna used with too high power, final output power transistors (SWR), inversion of polarities, bad connections, overvoltage,….) · The warranty cannot be extended due to the non-availability of the device while it is being serviced at our technical services location, nor by a change of one or more components or spare parts. · Transceivers which have been modified. The warranty application is excluded in case of modification or poor maintenance done by a third party not approved by our company.
If you note malfunctions: · Check the power supply of your device and the quality of the fuse.
26

English

· Check the different connections: jacks, antenna, etc. · Make sure that the various settings of your device are in the correct position. · In case the device is not under warranty, the repair and return of the device will be
charged. · All related documents must be preserved even after the end of the warranty period
and if you resell your device, given to the new owner for the After-sales follow-up. · In case of real malfunction, please contact your dealer first; they will decide action
to be taken. · In case of an intervention not covered by the warranty, an estimate will be established
before any repair. Thank you for your trust in the PRESIDENT quality and experience. We recommend that you read this manual carefully so that you are completely satisfied with your purchase. Do not forget to return the detachable warranty certificate on the right hand side of this page; it is very important for the identification of your device during a possible rendering of our services.
Technical Manager and
Quality Manager
!
Date of the purchase: Type: CB Radio JERRY Serial Number:………………………………………………….
not covered by the warranty without the dealer stamp
27

FREQUENCY TABLE

for EU / EC / U (CEPT) TABELA CZSTOTLIWOCI dla EU / EC / U (CEPT)

Channel Kanal
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Frequency Czstotliwo
26,965 MHz 26,975 MHz 26,985 MHz 27,005 MHz 27,015 MHz 27,025 MHz 27,035 MHz 27,055 MHz 27,065 MHz 27,075 MHz 27,085 MHz 27,105 MHz 27,115 MHz 27,125 MHz 27,135 MHz 27,155 MHz 27,165 MHz 27,175 MHz 27,185 MHz 27,205 MHz

Channel Kanal
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

Frequency Czstotliwo
27,215 MHz 27,225 MHz 27,255 MHz 27,235 MHz 27,245 MHz 27,265 MHz 27,275 MHz 27,285 MHz 27,295 MHz 27,305 MHz 27,315 MHz 27,325 MHz 27,335 MHz 27,345 MHz 27,355 MHz 27,365 MHz 27,375 MHz 27,385 MHz 27,395 MHz 27,405 MHz

FREQUENCY TABLE for U (ENG) TABELA CZSTOTLIWOCI dla U (ENG)

Channel Kanal
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Frequency Czstotliwo
27,60125 MHz 27,61125 MHz 27,62125 MHz 27,63125 MHz 27,64125 MHz 27,65125 MHz 27,66125 MHz 27,67125 MHz 27,68125 MHz 27,69125 MHz 27,70125 MHz 27,71125 MHz 27,72125 MHz 27,73125 MHz 27,74125 MHz 27,75125 MHz 27,76125 MHz 27,77125 MHz 27,78125 MHz 27,79125 MHz

Channel Kanal
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

Frequency Czstotliwo
27,80125 MHz 27,81125 MHz 27,82125 MHz 27,83125 MHz 27,84125 MHz 27,85125 MHz 27,86125 MHz 27,87125 MHz 27,88125 MHz 27,89125 MHz 27,90125 MHz 27,91125 MHz 27,92125 MHz 27,93125 MHz 27,94125 MHz 27,95125 MHz 27,96125 MHz 27,97125 MHz 27,98125 MHz 27,99125 MHz

FREQUENCY TABLE for d TABELA CZSTOTLIWOCI dla d

Channel Kanal
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Channel Kanal
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

FREQUENCY TABLE for d TABELA CZSTOTLIWOCI dla d

Channel Kanal
41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Frequency Czstotliwo
26,565 MHz 26,575 MHz 26,585 MHz 26,595 MHz 26,605 MHz 26,615 MHz 26,625 MHz 26,635 MHz 26,645 MHz 26,655 MHz 26,665 MHz 26,675 MHz 26,685 MHz 26,695 MHz 26,705 MHz 26,715 MHz 26,725 MHz 26,735 MHz 26,745 MHz 26,755 MHz

Channel Kanal
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80

Frequency Czstotliwo
26,765 MHz 26,775 MHz 26,785 MHz 26,795 MHz 26,805 MHz 26,815 MHz 26,825 MHz 26,835 MHz 26,845 MHz 26,855 MHz 26,865 MHz 26,875 MHz 26,885 MHz 26,895 MHz 26,905 MHz 26,915 MHz 26,925 MHz 26,935 MHz 26,945 MHz 26,955 MHz

FREQUENCY TABLE for PL TABELA CZSTOTLIWOCI dla PL

Channel Kanal
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Frequency Czstotliwo
26,960 MHz 26,970 MHz 26,980 MHz 27,000 MHz 27,010 MHz 27,020 MHz 27,030 MHz 27,050 MHz 27,060 MHz 27,070 MHz 27,080 MHz 27,100 MHz 27,110 MHz 27,120 MHz 27,130 MHz 27,150 MHz 27,160 MHz 27,170 MHz 27,180 MHz 27,200 MHz

Channel Kanal
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

Frequency Czstotliwo
27,210 MHz 27,220 MHz 27,250 MHz 27,230 MHz 27,240 MHz 27,260 MHz 27,270 MHz 27,280 MHz 27,290 MHz 27,300 MHz 27,310 MHz 27,320 MHz 27,330 MHz 27,340 MHz 27,350 MHz 27,360 MHz 27,370 MHz 27,380 MHz 27,390 MHz 27,400 MHz

FREQUENCY TABLE for In TABELA CZSTOTLIWOCI dla In

Channel Kanal
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Channel Kanal
21 22 23 24 25 26 27

Frequency Czstotliwo
27,215 MHz 27,225 MHz 27,255 MHz 27,235 MHz 27,245 MHz 27,265 MHz 27,275 MHz

F – NORMES · F – NORMAS · F – NORMES · F – NORMAS
Note: In U configuration, press MODE key (10) to alternate the frequency band between ENG and CEPT. “UK” appears in the display when the ENG band is selected. “UK” disappears from the display when CEPT is selected (see table at page 28). Uwaga: W konfiguracji U, nacinij przycisk MODE (10), aby przelczy pasmo czstotliwoci midzy ENG i CEPT. ,,UK” pojawia si na wywietlaczu po wybraniu pasma ENG. ,,UK” zniknie z wywietlacza po wybraniu CEPT (patrz tabela na stronie 28). The frequency band and the transmission power of your transceiver must correspond with the configuration authorized in the country where it is used. Czstotliwo oraz moc nadawania Twojego radiotelefonu musi by zgodna z wymaganiami kraju, w którym jest on uywany.
SIMPLIFIED EU DECLARATION OF CONFORMITY
Hereby, Groupe President Electronics, declares that the radio equipment :
Brand: PRESIDENT Type: TXPR612 Commercial Name: JERRY is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address: https://president-electronics.com/DC/TXPR612.
34

Please see updated table on website www.president-electronics.com, page «The CB radios» then «President Radio CB and Europe».
Ostatnia aktualizacja tej tabeli na stronie www.president-electronics.com, rubryka “les Postes Radio-CB” i “La CB PRESIDENT et l’Europe”.

UK
SIEGE SOCIAL/HEAD OFFICE – FRANCE Route de Sète – BP 100 – 34540 BALARUC Site Internet : http://www.president-electronics.com E-mail : groupe@president-electronics.com

2xxx/01-21 v0.00

Documents / Resources

PRESIDENT Jerry II Mobile CB Radio [pdf] Owner's Manual
Jerry II Mobile CB Radio, Jerry II, Mobile CB Radio, CB Radio, Radio

References

User Manual

PRESIDENT Jerry II Mobile CB Radio Owner’s Manual

PRESIDENT Jerry II Mobile CB Radio

Product Information

Product Usage Instructions

Frequently Asked Questions

INSTALLATION

MENU SETTING

SCAN SKIP

FUNCTION TURNING ON THE UNIT

TROUBLESHOOTING

INTERNATIONAL PHONETIC ALPHABET

GENERAL WARRANTY CONDITIONS

FREQUENCY TABLE

Documents / Resources

References

Leave a comment

Cancel reply