RUGGED-RIDGE-logo

RUGGED RIDGE 11586.09 Offroad Jack Mounting Bracket

RUGGED-RIDGE-11586-09-Offroad-Jack-Mounting-Bracket-product

Product Information

The Offroad Jack Mounting Bracket, JT is a component used to securely mount an off-road jack onto a vehicle. It includes various components listed below:

Component Quantity
Mount, Rear (near tailgate) (1)
Mount, Front (over wheelwell) (1)
M8 Nut Plate (2)
Hand Knob (threaded) (2)
M8-1.25 x 30mm Allen Head Bolt (2)
M10-1.5 x 45mm Carriage Bolt (2)
M10 Washer (2)
M8 Washer (2)
Rubber Isolator (2)

Product Usage Instructions

  1. Place the rear mount near the tailgate of the vehicle.
  2. Place the front mount over the wheel well of the vehicle.
  3. Take the M10 carriage bolt and insert it through each bracket.
  4. Place the rubber isolator over the threads of the carriage bolt.
  5. Position the off-road jack over the carriage bolt.
  6. Install the M10 washer onto the carriage bolt.
  7. Thread the hand knob onto the carriage bolt.
  8. Adjust the mounts on the track to ensure they do not bind to the body.
  9. Ensure that the mounts are flat against the body and track bar.
  10. Fully tighten the M8-1.25 x 30mm Allen Head Bolt.
  11. Snugly tighten the hand knob.

Components

RUGGED-RIDGE-11586-09-Offroad-Jack-Mounting-Bracket-fig-1

  1. Mount, Rear (near tailgate)………………….. (1)
  2. Mount, Front (over wheelwell)………………. (1)
  3. M8 Nut Plate………………………………………… (2)
  4. Hand Knob (threaded)………………………… (2)
  5. M8-1.25 x 30mm Allen Head Bolt…………… (2)
  6. M10-1.5 x 45mm Carriage Bolt………………. (2)
  7. M10 Washer…………………………………………. (2)
  8. M8 Washer…………………………………………… (2)
  9. Rubber Isolator…………………………………….. (2)

Installation Instructions

RUGGED-RIDGE-11586-09-Offroad-Jack-Mounting-Bracket-fig-2

  1. To use the mounts it may require adjusting the jack mechanism up from the lowest position. This will allow the rear mount to support the jack near the jack foot plate.
    • Begin by sliding the nut plates into your JT track system. It may require inserting the nut plate at the front of the track and slide it to the desired position.
    • With both nut plates installed, thread the M8 Allen head bolt and washer through the bracket into the nut plate. Position the mounts to the desired area using the offroad jack as reference.
    • NOTE: To determine front and rear mounts, the rear mount has a wider spread from the body.
  2. Place a M10 carriage bolt through each bracket. Then place the rubber isolator over the carriage bolt threads. Now position your off-road jack over the carriage bolt then install the M10 washer and thread the hand knob to the carriage bolt.
    • Adjust mounts on the track to not bind to the body, assuring the mounts are flat against the body and track bar. Fully tighten the Allen bolt and snug the hand knob.

ATTN: STATE OF CALIFORNIA CONSUMERS

WARNING: Cancer and Reproductive Harm –www.P65Warnings.ca.gov.

Contact

  • 460 HORIZON DR. SUWANEE, GA 30024
  • PHONE: 770-614-6101
  • FAX: 844-270-0593
  • www.Omix-ADA.com

OMIX-ADA® TECHNICAL SUPPORT

Copyright © 2020 Omix-Ada®, Inc.

Documents / Resources

RUGGED RIDGE 11586.09 Offroad Jack Mounting Bracket [pdf] Installation Guide
11586.09 Offroad Jack Mounting Bracket, 11586.09, Offroad Jack Mounting Bracket, Jack Mounting Bracket, Mounting Bracket, Bracket

References

Leave a comment

Your email address will not be published. Required fields are marked *