BOSCH-18V-150-C-GSR-GSB-Professional-Cordless-Drill-Driver-logo

BOSCH 18V-150 C GSR, GSB Professional Cordless Drill Driver

BOSCH-18V-150-C-GSR-GSB-Professional-Cordless-Drill-Driver-01

Original instructions

BOSCH-18V-150-C-GSR-GSB-Professional-Cordless-Drill-Driver-02

BOSCH-18V-150-C-GSR-GSB-Professional-Cordless-Drill-Driver-03

BOSCH-18V-150-C-GSR-GSB-Professional-Cordless-Drill-Driver-04

BOSCH-18V-150-C-GSR-GSB-Professional-Cordless-Drill-Driver-05

Safety Instructions

General Power Tool Safety Warnings
WARNING Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all in-structions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cord-less) power tool.

Work area safety

  • Keep work area clean and well lit. Cluttered or dark areas invite accidents.
  • Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
  • Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
Electrical safety
  • Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
  • Avoid body contact with earthed or grounded sur-faces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
  • Do not expose power tools to rain or wet conditions.
    Water entering a power tool will increase the risk of electric shock.
  • Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
  • When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suit-able for outdoor use reduces the risk of electric shock.
  • If operating a power tool in a damp location is un-avoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
Personal safety
  • Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
  • Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal in-juries.
  • Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
  • Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal in-jury.
  • Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
  • Dress properly. Do not wear loose clothing or jeweler. Keep your hair and clothing away from moving parts. Loose clothes, jeweler or long hair can be caught in moving parts.
  • If devices are provided for the connection of dust ex-traction and collection facilities, ensure these are connected and properly used. Use of dust collection can re-duce dust-related hazards.
  • Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe in-jury within a fraction of a second.

Power tool use and care

  • Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was de-signed.
  • Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
  • Disconnect the plug from the power source and/or re-move the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
  • Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
  • Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
  • Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
  • Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into ac-count the working conditions and the work to be per-formed. Use of the power tool for operations different from those intended could result in a hazardous situation.
  • Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

Battery tool use and care

  • Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
  • Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
  • When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
  • Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
  • Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
  • Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130°C may cause explosion.
  • Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

Service

  • Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
  • Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.
Safety information for drills and screwdrivers

Safety instructions for all operations

  • Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss.
  • Use the auxiliary handle(s). Loss of control can cause personal injury.
  • Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory or fasteners may contact hidden wiring. Cut-ting accessory or fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

Safety instructions when using long drill bits

  • Never operate at higher speed than the maximum speed rating of the drill bit. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury.
  • Always start drilling at low speed and with the bit tip in contact with the workpiece. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury.
  • Apply pressure only in direct line with the bit and do not apply excessive pressure. Bits can bend causing breakage or loss of control, resulting in personal injury.

Additional safety warnings

  • Hold the power tool securely. When tightening and loosening screws be prepared for temporarily high torque reactions.
  • Secure the workpiece. A workpiece clamped with clamping devices or in a vice is held more secure than by hand.
  • Use suitable detectors to determine if there are hid-den supply lines or contact the local utility company for assistance. Contact with electric cables can cause fire and electric shock. Damaging gas lines can lead to ex-plosion. Breaking water pipes causes property damage.
  • Always wait until the power tool has come to a complete stop before placing it down. The application tool can jam and cause you to lose control of the power tool.
  • In case of damage and improper use of the battery, vapors may be emitted. The battery can set alight or explode. Ensure the area is well ventilated and seek medical attention should you experience any adverse effects. The vapors may irritate the respiratory system.
  • Do not open the battery. There is a risk of short-circuiting.
  • The battery can be damaged by pointed objects such as nails or screwdrivers or by force applied externally. An internal short circuit may occur, causing the battery to burn, smoke, explode or overheat.
  • Only use the battery with products from the manufacturer. This is the only way in which you can protect the battery against dangerous overload.
    Protect the battery against heat, e.g. against continuous intense sunlight, fire, dirt, water and moisture. There is a risk of explosion and short-circuiting.
  • Switch the power tool off immediately if the application tool becomes blocked. Be prepared for high torque reactions which cause kickback. The application tool becomes blocked when it becomes jammed in the workpiece or when the power tool becomes over-loaded.
  • Caution! When using the power tool with Bluetooth®, a fault may occur in other devices and systems, aero-planes and medical devices (e.g. pacemakers, hearing aids). Also, damage to people and animals in the immediate vicinity cannot be completely excluded. Do not use the power tool with Bluetooth® in the vicinity of medical devices, petrol stations, chemical plants, areas with a potentially explosive atmosphere or in blasting areas. Do not use the power tool with Bluetooth® in aircraft. Avoid using the product near your body for extended periods.

The Bluetooth® word mark and logos are registered trade-marks owned by Bluetooth SIG, Inc. and any use of such marks by Robert Bosch Power Tools GmbH is under li-cense.

Product Description and Specifications

Read all the safety and general instructions. Failure to observe the safety and general instructions may result in electric shock, fire and/or serious injury.

Please observe the illustrations at the beginning of this operating manual.

Intended use

The power tool is intended for driving and loosening screws and for drilling in wood, metal, ceramic and plastic. The GSB is also designed for impact drilling in brick, masonry and stone.
With the Bluetooth® Low Energy Module GCY 42 inserted, power tool data and settings can be transferred between the power tool and a mobile device by means of Bluetooth® wire-less technology.

Product Features

The numbering of the product features refers to the diagram of the power tool on the graphics page.

  1. Tool holder
  2. Keyless chuck
  3. Depth stop
  4. Auxiliary handle (insulated gripping surface)
  5. Wing bolt for depth stop adjustment
  6. Torque presetting ring
  7. Mode selector switch
  8. Gear selector switch
  9. LED for electronic angle detection (EAD)
  10. Belt clip
  11. Rechargeable battery
  12. Battery release button
  13. Work light (user interface)
  14. User interface
  15. Bit holder)
  16. Rotational direction switch
  17. On/off switch
  18. Handle (insulated gripping surface)
  19. Bluetooth® Low Energy Module cover GCY 42
  20. Button for electronic angle detection (EAD) (user interface)
  21. LED for preset slope angle of electronic angle detection (EAD) (user interface)
  22. LED for power tool (user interface)
  23. LED for Kickback Control (user interface)
  24. Button for Kickback Control (user interface)
  25. Auxiliary handle order number 1 602 025 07Y
    1. Accessories shown or described are not included with the product as standard. You can find the complete selection of accessories in our accessories range.
Technical Data

BOSCH-18V-150-C-GSR-GSB-Professional-Cordless-Drill-Driver-07

BOSCH-18V-150-C-GSR-GSB-Professional-Cordless-Drill-Driver-08

  1. Measured at 20–25 °C with rechargeable battery ProCORE18V 8.0Ah.
  2. Measured with GBA 18V 1.5Ah and GBA 18V 12.0Ah.
Noise/Vibration Information

BOSCH-18V-150-C-GSR-GSB-Professional-Cordless-Drill-Driver-09

The vibration level and noise emission value given in these instructions have been measured in accordance with a standardized measuring procedure and may be used to com-pare power tools. They may also be used for a preliminary estimation of vibration and noise emissions.
The stated vibration level and noise emission value represent the main applications of the power tool. However, if the power tool is used for other applications, with different application tools or is poorly maintained, the vibration level and noise emission value may differ. This may significantly increase the vibration and noise emissions over the total working period.
To estimate vibration and noise emissions accurately, the times when the tool is switched off or when it is running but not actually being used should also be taken into account. This may significantly reduce vibration and noise emissions over the total working period.
Implement additional safety measures to protect the operator from the effects of vibration, such as servicing the power tool and application tools, keeping their hands warm, and organizing workflows correctly.

Assembly

  • Remove the battery from the power tool before carrying out work on the power tool (e.g. maintenance, changing tool, etc.). The battery should also be re-moved for transport and storage. There is risk of injury from unintentionally pressing the on/off switch.

Using the GCY 42 Bluetooth® Low Energy Module
Read the corresponding operating instructions for information about the Bluetooth® Low Energy Module GCY 42.

Charging the Battery
  • Use only the chargers listed in the technical data. Only these chargers are matched to the lithium-ion battery of your power tool.

Note: The battery is supplied partially charged. To ensure full battery capacity, fully charge the battery in the charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without reducing its service life. Interrupting the charging process does not damage the battery.
The lithium-ion battery is protected against deep discharge by the “Electronic Cell Protection (ECP)”. When the battery is discharged, the power tool is switched off by means of a protective circuit: The application tool no longer rotates.

  • Do not continue to press the On/Off switch after the power tool has automatically switched off. The battery can be damaged.

Follow the instructions on correct disposal.

Removing the Battery
The battery (11) is equipped with two locking levels to pre-vent the battery from falling out when pushing the battery re-lease button (12) unintentionally. As long as the battery is inserted in the power tool, it is held in position by means of a spring.
To remove the battery (11), press the release button (12) and pull the battery out of the power tool. Do not use force to do this.

Battery charge indicator
The green LEDs on the battery charge indicator indicate the state of charge of the battery. For safety reasons, it is only possible to check the state of charge when the power tool is not in operation.
Press the button for the battery charge indicator  or to show the state of charge. This is also possible when the battery is removed.
If no LED lights up after pressing the button for the battery charge indicator, then the battery is defective and must be replaced.
Note: The state of charge of the battery is also displayed on the user interface (14) (see “Status Indications”, page 22).

Battery model GBA 18V…

BOSCH-18V-150-C-GSR-GSB-Professional-Cordless-Drill-Driver-10

Battery model ProCORE18V…

BOSCH-18V-150-C-GSR-GSB-Professional-Cordless-Drill-Driver-11

Auxiliary handle

  • Do not operate your power tool without the auxiliary handle (4).
    This power tool must only be used with the auxiliary handle with the order number 1 602 025 07Y.
  • Before carrying out any work, make sure that the auxiliary handle is tightened. Loss of control can cause personal injury. Ensure that the auxiliary handle is tightened with a torque suited to the fastening method; fasten this to the power tool so that any movement of the auxiliary handle around or along the drilling axis is avoided.

Fitting the auxiliary handle
To open the auxiliary handle, turn the lower gripping end of the auxiliary handle (4) in an anticlockwise direction. Pull back the intermediate piece of the auxiliary handle and hold it in this position.
Slide the auxiliary handle over the drill chuck to mount the auxiliary handle on the power tool.

Then let go of the intermediate piece .
Afterwards, turn the lower gripping end of the auxiliary handle (4) clockwise to retighten it.

Swiveling the auxiliary handle
You can swivel the auxiliary handle (4) to any angle for a safe work posture that minimizes fatigue.
Turn the lower gripping end of the auxiliary handle (4) anti-clockwise and swivel the auxiliary handle (4) into the required position. Afterwards, turn the lower gripping end of the auxiliary handle (4) clockwise to retighten it.

Setting the drilling depth
You can use the depth stop (3) to set the required drilling depth X.
Loosen the wing bolt for adjusting the depth stop (5) and insert the depth stop into the auxiliary handle (4).
Pull the depth stop (3) far enough out that the distance between the drill bit tip and the edge of the depth stop (3) corresponds to the required drilling depth X.
Retighten the wing bolt for adjusting the depth stop (5).

Changing the tool (see figure A)

  • Remove the battery from the power tool before carrying out work on the power tool (e.g. maintenance, changing tool, etc.). The battery should also be re-moved for transport and storage. There is risk of injury from unintentionally pressing the on/off switch.

The drill spindle is locked when the on/off switch (17) is not pressed. This makes it possible to change the application tool in the drill chuck quickly, conveniently and easily.
Open the keyless chuck (2) by turning it in the direction of rotation

  1. until the tool can be inserted. Insert the tool. Firmly tighten the keyless chuck (2) by turning it by hand in the direction of rotation
  2. This will automatically lock the drill chuck.
Dust/Chip Extraction

Dust from materials such as lead-containing coatings, some wood types, minerals and metal can be harmful to one’s health. Touching or breathing-in the dust can cause allergic reactions and/or lead to respiratory infections of the user or bystanders.
Certain dust, such as oak or beech dust, is considered carcinogenic, especially in connection with wood-treatment additives (chromate, wood preservative). Materials containing asbestos may only be worked by specialists.

  • Provide for good ventilation of the working place.
  • It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the materials to be worked.

  • Avoid dust accumulation at the workplace. Dust can easily ignite.

Operation

Starting Operation

Inserting the battery
Note: The use of batteries unsuitable for your power tool can lead to malfunctions or damage to the power tool.
Set the rotational direction switch (16) to the middle position to avoid unintentionally switching it on. Insert the charged battery (11) into the handle until you feel it engage and it is flush with the handle.

Setting the rotational direction (see figure B)
The rotational direction switch (16) is used to change the rotational direction of the power tool. However, this is not possible while the on/off switch (17) is being pressed.

Rotate clockwise: Slide the rotational direction switch (16) on both sides until it stops in the position.
Rotate anti-clockwise: Slide the rotational direction switch (16) on both sides until it stops in the position.

Setting the operating mode
  • Drilling
    Set the mode selector switch (7) to the “drilling” symbol.
  • Screw driving
    Set the mode selector switch (7) to the “screw-driving” symbol.
  • Impact drilling (GSB 18V-150 C)
    Set the mode selector switch (7) to the “impact drilling” symbol.

Switching on/off
To start the power tool, press and hold the on/off switch (17).
The LED (13) lights up when the on/off switch (17) is lightly or fully pressed, meaning that the work area is illuminated in poor lighting conditions.
To switch off the power tool, release the on/off switch (17).

Adjusting the Speed
You can adjust the speed of the power tool when it is on by pressing in the on/off switch (17) to varying extents.
A light pressure on the on/off switch (17) results in a low rotational speed. Increased pressure on the switch causes an increase in speed.
Preselecting torque (applies to screw driving mode) The torque presetting ring (6) can be used to preselect the required torque in 25 stages. Once the set torque has been reached, the application tool will be stopped.

Mechanical gear selection

  • Only operate the gear selector (8) when the power tool is not in use.

First gear:
Low speed range; for working with a large drilling diameter or for screw driving.

Second gear:
High speed range; for working with a small drilling diameter.

  • Always push the gear selector switch as far as it will go. Otherwise, the power tool may become damaged.

Rapid Shut-off (Kickback Control)
The rapid shut-off function (Kick Back Control) gives the user greater control over the power tool and offers them better protection than power tools that do not have Kick-

Back Control. The power tool will switch off if it suddenly and unforeseeably rotates around the drilling axis.
The rapid shut-off is indicated by the LED (22) flashing red, a flashing light from the work light (13) and the LED of the Kick Back Control (23) lighting up red on the power tool.
To switch the tool back on, release the on/off switch and then press it again.

  • It will no longer be possible to switch the power tool on if the Kick Back Control function is faulty. Have the power tool serviced by a qualified repair person using only original replacement parts.

The rapid shut-off function can be deactivated on the user interface (14) with the button (24). If the power tool is not used for longer than 5 minutes or if the rechargeable battery is removed, the rapid shut-off function automatically switches back on. The current status is shown via the LED for Kick Back Control (23) on the user interface (14). Please note that the warning light is not visible from all directions. The warning light is difficult to see in bright sunlight.

Electronic Angle Detection (EAD)
With electronic angle detection (EAD), a slope angle can be preselected that the power tool detects during work and dis-plays to the user. This means it is possible to drill or screw at right angles in a sloped surface, for example. Electronic angle detection (EAD) is controlled via the user interface (14).
Select an angle (45°, 60°, user-defined) on the user interface (14). Note: The user-defined angle in the factory settings is 90°. This angle can be adjusted via the Bosch app. To adjust the angle, press the button for the electronic angle detection (EAD) (20) until the LED of the required slope angle (21) starts flashing.
In addition to the LED of the required slope angle (21), the LED of the electronic angle detection (EAD) (9) also starts to flash yellow. Now position the power tool on the required surface and hold it as still as possible. Note: If the power tool is not held still during the initiating process, the initiating process will automatically end after 10 seconds and the last set value is restored.
The power tool will start the initiating process once it is positioned. The required surface is taught in during the initiating process. The initiating process is complete when the LED of the electronic angle detection (EAD) (9) lights up green for approx. 1 second and then goes out, and the LED of the slope angle (21) lights up continuously.
Remove the power tool from the surface. Align the power tool with the taught-in surface in the required slope angle. The LED (22) lights up yellow if the slope angle lies in the range +/-10° from the preset slope angle.
If a slope angle within +/– 3° of the preset slope angle is reached, the LED (9) lights up green. To end the electronic angle detection (EAD), press the button for the electronic angle detection (EAD) (20) until none of the LEDs for angle selection (21) are lit up (45° → 60° → User-defined → Off). The set angle and reference surface are saved even when changing the rechargeable battery or when waking up the power tool from sleep mode.

User Interface (see figure D)
The user interface (14) is used to set and check a slope angle as part of the electronic angle detection (EAD), to de-activate the rapid shut-off (Kick Back Control) and to indicate the status of the power tool.

Status Indications

BOSCH-18V-150-C-GSR-GSB-Professional-Cordless-Drill-Driver-12

BOSCH-18V-150-C-GSR-GSB-Professional-Cordless-Drill-Driver-13

  1. The absolute measuring accuracy can vary based on different conditions (e.g. misalignment of the tool with the screw based on the interaction between screwdriver bit and/or adaptor; evenness of the surface which is referred to; etc.)

Connectivity functions
In conjunction with the Bluetooth® Low Energy Module GCY 42, the following connectivity functions are available for the power tool:

  • Registration and personalization
  • Status check, output of warning messages
  • General information and settings
  • Management
    Read the corresponding operating instructions for information about the Bluetooth® Low Energy Module GCY 42.

Practical advice

  • With the Bluetooth® Low Energy Module GCY 42, the power tool is equipped with a radio interface. Local operating restrictions, e.g. in aircraft or hospitals, must be observed.
  • Only apply the power tool to the screw when the tool is switched off. Rotating application tools can slip off.

An auxiliary tool can be used to remove the screwdriver bit or universal bit holder.

Belt clip
You can use the belt clip (10) to hang the power tool on a belt, for example. You then have both hands free and the power tool is always at hand.

Maintenance and Service

Maintenance and Cleaning
  • Remove the battery from the power tool before carrying out work on the power tool (e.g. maintenance, changing tool, etc.). The battery should also be re-moved for transport and storage. There is risk of injury from unintentionally pressing the on/off switch.
  • To ensure safe and efficient operation, always keep the power tool and the ventilation slots clean.

After-Sales Service and Application Service
Our after-sales service responds to your questions concerning maintenance and repair of your product as well as spare parts. You can find explosion drawings and information on spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you with any questions about our products and their accessories.
In all correspondence and spare parts orders, please always include the 10‑digit article number given on the nameplate of the product.

Great Britain

  • Robert Bosch Ltd. (B.S.C.)
  • P.O. Box 98
  • Broadwater Park
  • North Orbital Road
  • Denham Uxbridge
  • UB 9 5HJ
  • At www.bosch-pt.co.uk you can order spare parts or arrange the collection of a product in need of servicing or repair.
  • Tel. Service: (0344) 7360109
  • E-Mail: boschservicecentre@bosch.com

You can find further service addresses at:

Transport

The recommended lithium-ion batteries are subject to legislation on the transport of dangerous goods. The user can transport the batteries by road without further require-ments.
When shipping by third parties (e.g.: by air transport or for-warding agency), special requirements on packaging and la-belling must be observed. For preparation of the item being shipped, consulting an expert for hazardous material is re-quired.
Dispatch battery packs only when the housing is undam-aged. Tape or mask off open contacts and pack up the bat-tery in such a manner that it cannot move around in the packaging. Please also observe the possibility of more de-tailed national regulations.

Disposal
  • Power tools, rechargeable batteries, accessor-ies and packaging should be sorted for environ-mental-friendly recycling.
  • Do not dispose of power tools and batteries/re-chargeable batteries into household waste!

Only for EU countries:
According to the Directive 2012/19/EU on waste electrical and electronic equipment and its transposition into national law, power tools that are no longer usable, and, according to the Directive 2006/66/EC, defective or drained batteriesBOSCH-18V-150-C-GSR-GSB-Professional-Cordless-Drill-Driver-06

Licenses

Copyright © 2009–2020 ARM LIMITED
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

  • Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
  • Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
  • Neither the name of ARM nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMI-TED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTER-RUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (IN-CLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Copyright © 2011 Petteri Aimone
This software is provided ‘as-is’, without any express or implied warranty. In no event will the authors be held liable for any da-mages arising from the use of this software.
Permission is granted to anyone to use this software for any purpose, including commercial applications, and to alter it and re-distribute it freely, subject to the following restrictions:

  1. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an acknowledgment in the product documentation would be appreciated but is not required.
  2. Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software.
  3. This notice may not be removed or altered from any source distribution.

EU Declaration of Conformity
Cordless drill/ Article number driver
We declare under our sole responsibility that the stated products comply with all applicable provisions of the directives and regulations listed below and are in conformity with the following standards.
Technical filet: *BOSCH-18V-150-C-GSR-GSB-Professional-Cordless-Drill-Driver-14

Declaration of ConformityBOSCH-18V-150-C-GSR-GSB-Professional-Cordless-Drill-Driver-15

Documents / Resources

BOSCH 18V-150 C GSR, GSB Professional Cordless Drill Driver [pdf] Instruction Manual
18V-150 C GSR GSB Professional Cordless Drill Driver, 18V-150 C, GSR, GSB Professional, GSR Cordless Drill Driver, GSB Professional Cordless Drill Driver, Cordless Drill Driver, Cordless Drill, Cordless Driver, Drill Driver, Drill, Driver

References

Leave a comment

Your email address will not be published. Required fields are marked *