192, 14 air USB Audio Interface for Studio Recording

M-AUDIO®
Air 192 | 14

User Guide

Introduction

Thank you for purchasing the AIR 192|14. At M-Audio, we know how serious music is to you. That’s why we design our equipment with only one thing in mind—to make your performance the best it can be.

Box Contents

AIR 192|14
Power Adapter
USB-C to USB-C Cable
USB-C to USB-A Cable
(2) 1/8″ (3.5 mm) to MIDI Adapters
Software Download Cards
User Guide
Safety & Warranty Manual

Support

For the latest information about this product (documentation, technical specifications, system requirements, compatibility information, etc.) and product registration, visit m-audio.com.
For additional product support, visit m-audio.com/support.

Setup

Audio Setup

Windows users: Before connecting AIR 192|14 to your computer, install the driver:

  1. Go to m-audio.com/drivers and download the latest AIR 192|14 driver for your operating system.
  2. Open the file you downloaded and double-click the driver installer file.
  3. Read the End-User License Agreement, then check the box to Agree and click Next to
    continue.
  4. Click Install to begin the installation. You may be asked to connect AIR 192|14 to your computer during the installation process. Click Install on any further system messages during the installation.
  5. Once the installation is complete, click Finish.
    To use the Windows driver, open the M-Audio AIR 192|14 Control Panel. Here, you can set your Preferred Buffer Size and Sample Rate.

To set AIR 192|14 as your default playback device, follow the directions below based on your computer’s operating system.

Windows:

  1. Use the included USB cable to connect the AIR 192|14 to your computer. Press the power button to power on AIR 192|14.
  2. In the Taskbar, locate the Volume Control “speaker” icon. Right-click the speaker and select Playback Devices. Alternatively, go to Start Menu > Control Panel (or Settings > Control Panel in Classic View) > Hardware and Sound > Sound.
  3. In the Windows Sound control panel select the Playback tab and select AIR 192|14 as the default device.
  4. Click the Recording tab and select AIR 192|14 as the default device.
  5. Click Properties in the lower right-hand corner.
  6. In the new window, click the Advanced tab and select 2-channel, 24-bit, 48000 Hz (Studio Quality) as the default format.
  7. Uncheck both boxes under Exclusive Mode.
  8. Click OK to close the Properties window.
  9. Click OK to close the Sound control panel.

macOS:

  1. Use the included USB cable to connect the AIR 192|14 to your computer. Press the power button to power on AIR 192|14.
  2. Go to Applications > Utilities > Audio MIDI Setup.
  3. In the Audio Devices window, select AIR 192|14 in the left column.
  4. Right-click AIR 192|14, and select Use this device for sound input.
  5. Right-click AIR 192|14, and select Use this device for sound output.
  6. Quit Audio MIDI Setup.

Setting Up AIR 192|14 with Your Software
Setting Up AIR 192|14 with Pro Tools | First M-Audio Edition

  1. Use the included USB cable to connect the AIR 192|14 to your computer.
  2. Open Pro Tools | First M-Audio Edition.
  3. Go to Setup > Playback Engine….
  4. Open the Playback Engine dropdown menu and select M-Audio AIR 192|14.
    Note: You may need to save and restart your project.
  5. Select your Sample Rate and then click OK to close the Setup window.
  6. Go to the Setup > I/O and select M-Audio AIR 192|14 for the Input and Output devices.

You can now add tracks to send and receive audio and MIDI from sources connected to AIR 192|14 inputs and stream recorded audio back through the AIR 192|14 outputs.

Setting Up AIR 192|14 with Ableton Live Lite

  1. Use the included USB cable to connect the AIR 192|14 to your computer.
  2. Open Ableton Live Lite.
  3. Go to Preferences > Audio tab.
  4. Click on Driver Type to select Core Audio (Mac) or ASIO (Windows).
  5. Select AIR 192|14 in the Input and Output Config section.
  6. Select your Sample Rate and then close the audio preferences window.

You can now add tracks to send and receive audio and MIDI from sources connected to AIR 192|14 inputs and stream recorded audio back through the AIR 192|14 outputs.

Connection Diagrams

Items not listed under Introduction > Box Contents are sold separately.

Example 1

assembly audio Example 2

keyboard setup

Example 3

assembly parts

Features

Top Panel

top panel1. Power Button: Press this button to power
the AIR 192|14 on or off. The Power LED
below this button lights up when the unit
is powered on.

2. Input Gain: Adjusts the input’s gain level.
Set this knob so the corresponding LED
Meter (located below the knob) displays a
“healthy” level (yellow LED is lit) during performance—but not so high that the meter frequently “clips” or peaks (red LED is lit), causing distortion in the audio.

3. LED Meters (Inputs 1–6): Indicates the input signal level from the Combo Inputs and Instrument Inputs.

4. LED Meters (Inputs 7–8): Indicates the input signal level from the Line Inputs. These LEDs are green when a signal above -20 dBFS is present, and turn red when the signal “clips” or peaks.

5. +48 V (Phantom Power) Switches: These switches activate and deactivate phantom power for Combo Inputs 1–2 or 3–4. When activated, phantom power supplies +48 volts to the selected inputs. Please note that most dynamic microphones and ribbon microphones do not require phantom power, while most condenser microphones do. Consult your microphone’s documentation to find out whether it needs phantom power.

6. Monitor Level: Adjusts the output volume of Main Outputs, which should be connected to your powered monitors or amplifier system.

7. Monitor Mix: Adjusts the mix of the audio signal from your inputs (Direct) and the audio output of your computer (USB) that will be sent to the Main Outputs and Headphone Outputs.

Note: When set to Direct, the left channel will be a sum of Inputs 1, 3, 5, and 7 and the right channel will be a sum of Inputs 2, 4, 6, and 8. You can sum these left and right channels (to hear all inputs as a single summed mono signal) by putting the Direct Monitor button in its depressed position.

This knob is useful for dealing with “latency” when you are recording in your DAW. Latency is a delay in sound that may occur between the incoming sound (playing your instrument, singing, etc.) and outgoing sound (when you hear it in the DAW).
Latency is often the result of the “buffer size” setting, which is usually located in your DAW’s Preferences, Options, or Device Setup menu. Higher buffer sizes generally result in higher latency. In some cases, lower buffer size settings can consume a lot of your computer’s CPU and cause audio glitches. To prevent these audio glitches, you will need to use a higher buffer setting, and this may result in latency.

If you are experiencing latency when recording, adjust the knob towards the Direct position to increase the blend of unprocessed audio from your inputs directly to your Main Outputs and Headphone Outputs. This will let you hear the incoming audio from your inputs without latency while still being able to hear the audio from your DAW. When listening to the playback, adjust the knob all the way to the USB position.
If your computer is powerful enough, you may be able to set the buffer size setting in your DAW low enough such that you may never need to listen to the direct audio signal from your inputs. In this case, set the Monitor Mix knob all the way to the USB position to monitor only the audio output of your DAW.

8. Direct Monitor Selector: Leave this switch in the raised position (blue Stereo LED is lit) to monitor the direct input signal with Inputs 1, 3, 5, and 7 in the left channel and Inputs 2, 4, 6, and 8 in the right channel. This is useful if you want to directly monitor a stereo mic setup such as a stereo signal from a keyboard, or overhead drum mics. Put this switch in its depressed position (green Mono LED is lit) to monitor the direct input signal with all inputs summed and heard equally on each side. This is useful for monitoring a guitar or vocal mic signal. This switch does not affect the DAW playback or how your sound is recorded into your DAW; it affects only how you hear the input signal in the Headphone Outputs (when the Headphone Source Selector is set to 1/2, and the Monitor Mix is set to anything besides USB) and Monitor Outputs.

9. Headphone Source Selector: These switches select which outputs (on the rear panel) are also sent to the Headphone Outputs: Main Outputs 1–2 (1/2) or Outputs 3–4 (3/4).

10. Headphone Outputs (front panel): Connect 1/4″ (6.35 mm) TRS headphones to these outputs. The mix you hear from these outputs will be determined by the Headphone Source Selector, Monitor Mix knob, Direct Monitor Selector, and associated Headphone Volume knob.

11. Headphone Volume (front panel): Adjusts the output volume of the Headphone Outputs.

12. Instrument Inputs (5–6) (front panel): Connect a guitar with a passive pickup or other high-impedance signal to these inputs with a 1/4″ (6.35 mm) TS cable. View the input signal levels with the LED Meters (Inputs 5–6).

Rear Panel

rear panel1. Power: Connect the included power adapter to this input. Use the Power Button to turn AIR 192|14 on or off.

2. USB Port (Type C): This connection will allow you to send audio and MIDI data to and from a computer. Use the included USB-Cto-
USB-C or USB-C-to-USB-A cables to connect the AIR 192|14 to a computer. The
AIR 192|14 requires a USB 2.0 connection (or higher).

3. MIDI Out: Use the included 1/8″ (3.5 mm)-to-MIDI adapter and a standard five-pin MIDI cable to connect this MIDI Out to the MIDI In of an external MIDI device (e.g., a synthesizer, sequencer, drum machine, etc.).
Important: Do not connect audio devices (e.g., headphones, monitors, etc.) to this jack. Use the included 1/8”-to-MIDI adapter to connect MIDI devices only.

4. MIDI In: Use the included 1/8″ (3.5 mm)-to-MIDI adapter and a standard five-pin MIDI cable to connect this MIDI In to the MIDI Out of an external MIDI device (e.g., a MIDI controller).
Important: Do not connect audio devices (e.g., headphones, monitors, etc.) to this jack. Use the included 1/8″-to-MIDI adapter to connect MIDI devices only.

5. Outputs (3–4): Use standard 1/4″ (6.35 mm) TRS cables to connect these line outputs to a headphone amplifier, external signal processors like a compressor, etc. Their levels are automatically +4 dBu.

6. Main Outputs (1–2): Use standard 1/4″ (6.35 mm) TRS cables to connect these outputs to your powered monitors, amplifier system, etc. The mix you hear from these outputs will be determined by the Monitor Mix knob and Direct Monitor button. The level of these outputs is controlled by the Monitor Level knob.

7. Line Inputs (7–8): Connect mixers and other line-level devices to these inputs using standard 1/4″ (6.35
mm) TRS cables. View the input signal levels with the LED Meters (Inputs 7–8).

8. Combo Inputs (1–4): Connect microphones, a guitar or bass with an active pickup, or line-level devices to these inputs. For microphones, use an XLR or 1/4″ (6.35 mm) TRS cable. For a guitar or bass with an active pickup, use a standard 1/4″ TS cable. For line-level signals, use a 1/4″ TRS cable. View the input
signal levels with the LED Meters (Inputs 1–4).

9. Kensington Lock Slot: You can use this Kensington lock slot to secure AIR 192|14 to a table or other surface.

Technical Specifications  

All specifications are measured at 20 kHz bandwidth.

Mic Inputs 1–4 (balanced XLR)

Dynamic Range

113 dB (A-weighted)

THD+N

0.001% (1 kHz, +4 dBu, -1 dBFS)

Frequency Response

20 Hz – 20 kHz (+/-0.2 dB)

Preamp EIN

-137 dBu (40 Ω source, A-weighted)

-129 dBu (150 Ω source, unweighted)

Max Input Level

+14 dBu

Gain Range

62 dB

Line Inputs 1–4 (balanced 1/4″ TRS)

Dynamic Range

113 dB (A-weighted)

THD+N

0.001% (1 kHz, +4 dBu, -1 dBFS)

Frequency Response

20 Hz – 20 kHz (+/-0.1 dB)

Max Input Level

+30 dBu

Gain Range

61 dB

Inst Inputs 5-6 (unbalanced 1/4″ TS)

Dynamic Range

110 dB (A-weighted)

THD+N

0.001% (1 kHz, +4 dBu, -1 dBFS)

Frequency Response

20 Hz – 20 kHz (+/-0.1 dB)

Max Input Level

+16 dBu

Gain Range

59 dB

Input Impedance

~1 M

Fixed Line Inputs 7–8 (balanced 1/4″ TRS)

Dynamic Range

113 dB (A-weighted)

THD+N

0.001% (1 kHz, +4 dBu, -1 dBFS)

Frequency Response

20 Hz – 20 kHz (+/-0.1 dB)

Max Input Level

+17 dBu

Line Outputs 1–2 (balanced 1/4″ TRS)

Dynamic Range

112 dB (A-weighted)

THD+N

0.002% (1 kHz, -1 dBFS)

Frequency Response

20 Hz – 20 kHz (+/-0.2 dB)

Maximum Output Level

+17 dBu

Fixed Line Outputs 3–4 (balanced 1/4″ TRS)

Dynamic Range

113 dB (A-weighted)

THD+N

0.002% (1 kHz, -1 dBFS)

Frequency Response

20 Hz – 20 kHz (+/-0.2 dB)

Maximum Output Level

+17 dBu

Headphone Outputs (stereo 1/4″)

Dynamic Range

111 dB (A-weighted, 32 Ω load)

THD+N

0.002% (1 kHz, -1 dBFS, 10 mW/channel into 32 Ω load)

Frequency Response

20 Hz – 20 kHz (+/-0.2 dB)

Maximum Power Delivered

160mW (<1% THD, 32 Ω load)

Maximum Output Level

+15 dBu (unloaded)

Impedance Range

32 Ω – 600 Ω

General

Other Connectors

(1) 1/8” (3.5 mm) MIDI input  

(1) 1/8” (3.5 mm) MIDI output  

(1) USB Type-C port  

(1) Power adapter input

Power Adapter

12 VAC, 2 A, center-positive (included)

Dimensions  

(width x depth x height)

3.24″ x 10.2″ x 7.44″  

8.22 x 25.9 x 18.9 cm

Weight

3.9 lbs.  

1.8 kg

Specifications are subject to change without notice.  

Trademarks & Licenses  

M-Audio and AIR Music Tech are registered trademarks of in Music Brands, Inc., registered in the U.S. and  other countries.  

Ableton is a trademark of Ableton AG.  

Kensington and the K & Lock logo are registered trademarks of ACCO Brands.  

macOS is a trademark of Apple Inc., registered in the U.S. and other countries.  

Windows is a registered trademark of Microsoft Corporation in the United States and other countries.  All other product names, company names, trademarks, or trade names are those of their respective owners.

Documents / Resources

M-AUDIO 192, 14 air USB Audio Interface for Studio Recording [pdf] User Guide
14 air, 114 air, air USB Audio Interface, Audio Interface for Studio Recording, USB Audio Interface for Studio Recording, Audio Interface

References

Leave a comment

Your email address will not be published. Required fields are marked *