Frossvt H9 Electric Pasta Maker Automatic Noodle Making Machine Instruction Manual

Frossvt H9 Electric Pasta Maker Automatic Noodle Making Machine

• Before operating this appliance, please read these instructions completely.

Catalog

• Dear users, thank you for using our company’s fully automatic pasta maker.
• To facilitate your correct operation of this product please read this manual carefully before use and store it in a fixed place so that you can refer to it in the future.
• This product is for indoor use only! The company reserves the right of final interpretation.

Product feature

1. A variety of disc combinations can make Fettucine, spaghetti, etc.
2. You can add egg liquid, vegetable juice (soft vegetable leaves can be put directly, hard vegetables must be juiced), etc, to make noodles with different flavors, which are healthy and delicious.
3. The operation is simple, from flour to pasta, the whole process is easy to achieve.
4. Food grade material, hygienic, healthy, environmentally friendly, and practical.
5. imitate the hand kneading, pour the right amount of flour and water into the mixing bowl, and the machine will knead them and extrude pasta automatically.
6. Excess dough can be cleaned up easily by hand, simple and convenient.
7. Multiple safety protection devices, long-serve life.

Important safeguards

1. For household use only.
2. The maximum of this appliance is about 320 dry flour (2 flat cups of flour, the amount of water should be about 100ml. Amount of the water can be±5ml according to the humidity of the flour).
   • The minimum capacity is about 160g (1 flat cup of flour), and it needs about 60ml (The amount of the water can be according to the humidity of the flour).
3. Please add flour and water in strict accordance with the number of ingredients recommended in the reference table for the ratio of noodles to water. Otherwise, the noodles will be too dry or too wet, and the accessories may be damaged in severe cases.
4. When using the “extrude” function, make sure that the flour and water are evenly mixed before extruding. so as not to stick the hole of the discs with dry flour and cause damage to the accessories.
5. The product is equipped with an intelligent protective control program, which will automatically shut off after one noodle-making cycle.
6. Make sure the appliance is not plugged in when assembling or disassembling the appliance.
7. If the product needs to be repaired during use. please contact the company’s customer service department, or go directly to the repair point designated by the company for repairs. Do not disassemble it yourself to avoid danger.
8. Before use, please check whether the mixing bowl, extruding pipe, disc nut, and other detachable parts are damaged. If found damaged, please stop using the product. Please contact our Customer Service Department in time. Please do not disassemble and repair it by yourself, to avoid danger.
9. Please check the mixing bowl, extruding pipe, discs nut, and mixing axle before use.
10. During the working process of the product, it will intelligently identify the softness and hardness of the dough, and it will reverse during the process, Please check if the dough is too dry or if there are foreign objectives in the mixing bowl. If there are no foreign objectives, then add the appropriate amount of water into it, wait for 2 minutes of kneading, and then select extrude” mode, If it is still blocked, it is recommended to disconnect the power supply and clean the flour in the discs, Then continue to operate it.
11. When the product is working, it is strictly prohibited to add any non-liquid foreign objects to the mixing bowl (The eggs need to be mixed well with water).
12. After the product is connected to the power supply or during operation, if there is a flashing light alarm, please disconnect the power supply, and check whether there is a stuck of flour or other things. after cleaning it, reconnect the power supply to continue to use, if the display flashes and alarms, please go to the designated maintenance points of our company for repair.
13. When the product is working, it is strictly prohibited to open the top cover or unscrew the disc nut to take out the discs, and do not touch the extruding axle to avoid accidents.
14. All parts of this product are not allowed to be sterilized in a microwave oven to avoid thermal deformation and damage.
15. Do not immerse the main housing in water or other liquids.
16. Do not use steel wool, abrasive cleaners, or corrosive liquids (such as gasoline or acetone)to clean the product.
17. This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge of using the appliance. Unless they are closely supervised and instructed concerning the use of the appliance by a person responsible for their safety. Close supervision is necessary when any appliance is used by or near children. Children should be supervised to ensure that they do not play with the appliance.
18. Avoid exposure to the sun to avoid discoloration of the appearance.
19. It is strictly prohibited to disassemble or modify this product by yourself. 20、Do not put the main housing in the dishwasher for cleaning.
20. Do not heat the parts of this product.
21. This product is a Class I electrical appliance. The grounding wire of the socket must be well grounded.
22. When making egg noodles, please weigh the eggs and water. It is strictly forbidden to add eggs directly.
23. If the power cord is damaged, it must be replaced with a special soft cord or special components purchased from other manufacturers or maintenance departments.

Parts name

Parts function

Number	Parts name	Parts name
1	Housing	The power source of the product
2	Mixing Bowl	The container for mixing ingredients
3	Mixing Axle	For mixing flour and water, pressing noodles
4	Extruding pipe	Cooperate with the extruding axle to form the dough
5	Extruding Axle	Used in extruding the pasta
6	Discs	Accessories for shaping various kinds of pasta
7	Discs nut	Used for locking the discs.
8	Top cover lid	It is used to connect with the fuselage micro switch and play the role of safety protection
9	Water measuring cup	Weigh the mixture of water. vegetable juice and egg water
10	Flour cup	Used to weigh flour
11	Cleaning scraper	Measure the flour and scrape the flour

Use method

Before the first use of the product, please thoroughly clean the parts in contact with the ingredients.

Operation instructions

1. Plug in the power supply, the buzzer sounds once, the digital tube and indicator light are all on for 0.5 seconds and then go out, and the pasta maker enters the shutdown state.
2. In the shutdown state, press the “ON/OFF” button, and the pasta maker will enter the standby state, and then selecting the corresponding function and the pasta maker will work.
3. Knead Dough
   • In the standby state, select the “Knead Dough” button, and the buzzer will sound once, the pasta maker will enter the work reversal for 4 minutes, and the noodle mixing process will end.
4. Extrude Pasta
   • In the standby state, select the “Extrude Pasta” button, the buzzer will sound once, and the pasta maker will start to work for 4 minutes and 25 seconds, stop for 5 seconds, reverse for 30 seconds, and the appearance process is over.
5. Quick Noodles
   • In the standby state, select the “Quick Noodles” button, the buzzer will sound once, and the pasta maker will start to work, reverse for 3 minutes, stop for 5 seconds, and turn forward.
6. Pause
   • In the working state, select the “Pause” button, the buzzer will sound once, and the pasta maker will stop working. If you press the “Pause” button again, the pasta maker will resume the current working process.

Product disassembly instructions

1. Disassembly steps (before disassembly, be sure to turn off the switch and disconnect the power)
   1. Pull the lid to unlock it and then remove the lid from the mixing bowl.
   2. Turn the disc nut counterclockwise to remove it from the mixing bowl outlet.
   3. Detach the discs, and then puĄll the extruding axle out of the extruding pipe outlet.
   4. Remove the extruding pipe from the mixing bowl outlet.
   5. Slide the mixing chamber and mixing axle on the main unit, and then remove the mixing axle from the mixing bowl.
   6. Remove the mixing bowl.
2. Product installation steps (before installation, be sure to turn off the switch and disconnect the power)
   1. Put the mixing axle in the mixing bowl as shown in the illustration. Slide the mixing bowl onto the main unit. Insert the mixing axle into the main unit.
      • The outer hexagon hole of the extruding axle is fitted into the inner hexagon hole of the motor shaft.
      • lf it gets stuck in the assembly. rotate the extruding axle slightly to install it.
   2. Insert the extruding pipe into the mixing bowl.
   3. Insert the extruding axle into the mixing bowl.
   4. Attach the disc to the mixing bowl outlet. Make sure the shaping disc fits into the fixing point on the extruding pope and extruding axle.
   5. Assemble the discs nut on the mixing bowl outlet. Turn the disc nut clockwise to firmly lock it in place.
   6. First, aim the top cover lid clamping position at the front notch of the fuselage barrel, press down, and hear a”click”. and install well.
3. Product Usage
   1. Choose die disc The distribution die of this product is as follows:
   2. The water ratio

Amount of flour	Water	Vegetable juice	1egg+water
1cup(160g)	60ml	70ml	70ml
2cup(320g)	120ml	130ml	130ml

Note:

• The egg mixture and vegetable juice must be whisked evenly with the water before pouring into the mixing bowl.
• This ratio is only for all-purpose flour and water/egg/vegetable. If you experiment with or use other flour, the flour and water/eggs/vegetable ratios will need to be adjusted.
• The pasta maker will not operate successfully if you do not adjust the new recipe accordingly.

Warm prompt:

1. The egg mixture must be mixed well with water
2. The maximum surface volume is 320g(about two cups), and the minimum surface volume is 160g(about 1 flat cup). it is strictly prohibited from exceeding the capacity.
3. Use strictly under the recommended proportion of surface water. Abnormal failure caused by not following the instructions is not covered by the warranty

Noodle production process

1. First, remove the top cover lid
   • Pull the lid to unlock it and then remove the lid from the mixing bowl. Do not put less than 160g (about 1 flat cup) or more than 320g (about 2 flat cup) of flour in the mixing bowl.
2. Measuring the flour
   • Scoop one full cup of flour by the flour cup. Scrape off the excessive flour from the cup edge with the cleaning scraper (refer to illustration B). 1 full cup of flour weighs around 160 g, and 2 full cups of flour weigh around 320g.
3. Measuring the liquid
   • Method 1(illustration A): Look over the water cup and see where the water meets the scale.
   • Method 2(illustration B): Measure the liquid volume at eye level on a flat surface.

Note: Do not pour liquid into the mixing bowl before the pasta maker starts running. The cups must be placed on a stable or even surface.

1. Pour the measured flour into the mixing bowl
2. Take the lid to align with the two notches in the top of the main housing, and then press it down until you hear a click”. Lock the cover lid onto the mixing bowl.
3. Put the plug in the power socket, press the “On/OFF” button, and then press the “Quick Noodles” button. After the kneading starts, slowly pour in the measured liquid along the entire length of the slot in the lid.
   • Note: Pour in the liquid after the appliance starts mixing.
4. After about 10 minutes(When the extrusion process is complete, the appliance will beep for once.

Cleaning method

1. Step 1: Disassemble the appliance and Then use a dry cloth to clean flour residue on the main unit, and use the cleaning scraper and wet cloth to clean the dough residues.
2. Step 2: Let the dough residues air-dry for some time, and then use the cleaning scraper and wet cloth to clean other detachable parts.
3. Step 3: Let the discs air-dry for 2 to 4 hours. Then use the corresponding cleaning tool to poke out the dough in the holes.

Reminder: After using the noodle maker, do not clean it immediately. Remove the parts that are in contact with the flour, freeze or leave it to dry before cleaning. it is forbidden to immerse the housing in water or other liquids to avoid leakage of electricity.

Common usage problems

1. The indicators do not light up.
   • Check whether the power plug is plugged correctly and the outlet is working properly.
2. During the pasta extruding process, there is no pasta coming out.
   1. The ratio of the flour and water is incorrect or The flour becomes damp after long storage. Disconnect the plug from the power source, remove the damp dough from the mixing bowl and tear it into small pieces(about 2-3cm), put it into the mixing bowl again, and then mix and extrude it again.
   2. The flour becomes too dry because of the incorrect ratio. Add a small amount of water to mix and extrude it again.
3. Which noodles can be made in the automatic mode?
   • The pasta maker has 8 discs, which can make noodles of various shapes, and can also add egg liquid, vegetable juice (soft vegetable leaves can be put into mixing with flour directly, hard vegetables must be juiced), etc. to make noodles with different flavors.
4. What should I do if too much leftover dough inside the mixing bowl?
   1. The dough is too wet or the flour is damp. Please make sure that the flour is stored in a dry container. You can fine-tune the moisture according to the water ratio and refer to the table to make the flour again.
   2. The mixing bowl, extruding pipe, discs nut, and extruding axle are not cleaned before work. Please make sure that the relevant parts are dry.
   3. The order of adding water is wrong or the type of flour is wrong.
5. How to use our measuring cup correctly?
   1. Take out the flour measuring cup, and fill it with flour and scrape the excess flour along the edge of the cup with the attached cleaning spatula, that is, a full cup. (Serving for 1~2 people, about 160g).
6. Is not inconvenient to clean the pasta maker discs?
   • • After the noodles in the disc are completely dry, tap on the hard board and the noodles will fall off automatically.
7. There are more burrs or cracks?
   1. Due to mixing reasons, the noodles will have large burrs or cracks at the beginning and the end of the noodles. If smooth, you can add eggs or a proper amount of cooking oil to significantly improve the burrs and cracks of the noodles.
   2. lf you have enough time, you can also tear the finished noodles into peanut-sized dough. Please Weigh and put a little flour into the mixing bowl, press the Knead key to knead them for a while, and then choose the extrude mode to extrude the noodles again. The more times you repeat the smoother and chewy the noodles are.
8. How can we make noodles successfully?
   1. Use the flour measuring cup and measuring cup provided to the pasta maker to measure the flour and water, and the ratio of flour and liquid must be strictly under ratio instructions.
   2. Please add flour first, and cover the top cover lid, after the standby machine is running, pour water (liquid ) into the mixing bowl through the slot hole on the top cover lid slowly and evenly.
9. Does the pasta maker have flour requirements?
   • It is recommended to use an all-purpose flour.
10. There is a small amount of flour remaining after making it, how to deal with it?
    • You can turn the machine first. pour out the remaining noodles and put them together, then put them in the mixing bowl, and press the “Extrude” button to continue pressing.
11. The noodles that come out are hot, and they will stick together when they reach a certain length. Is there a solution?
    1. After the noodles come out, sprinkle some dry flour to make the noodles much more chewy and not sticky.
    2. Please cut the noodles in time not to be too long!
12. Will the amount of noodles come out crack? How to solve it?
    • The face will be interrupted, most of which are because of the lack of water. Please strictly follow the proportion of the instructions.

The noodles that came out were hot. it will stick together at a certain length. Is there a solution?

• After the noodles come out, sprinkle some dry flour to make the noodles more gluten-free and not sticky. Please cut it in time, do not let it be too long.

What is the situation of the face meeting when I come out and how to solve it?

• The surface will be cracked mostly because there is less water added, please strictly follow the proportion of the instructions.
• Treatment method of dry or wet noodles. Too wet or dry noodles may cause the noodles to stick or break easily, or even stop the machine. At this time, you can refer to the following solutions:

The noodles are too dry:

• Add the proper amount of water and press the automatic button again. If you re-make the noodles, add 10-20mL of water appropriately.

The dough is too wet:

• Add dry flour in an appropriate amount and press the automatic button again. If vou re-make the noodles, you need to reduce 10-20mL of water appropriately.
• The surface water ratio is appropriate. and the flour is loose and large flocculent.
• If the flour is too dry, add the proper amount of water. and then press the automatic button
• The dough is too wet, after adding a proper amount of dry flour, press the automatic button again to mix and extrude it again.

Packing List

Product specifications

Product name	Pasta maker
Product model	H9
Rated voltage	220-240V~
Rated frequency	50/60Hz
Rated power	180W

Packing list

Pasta maker	Discs	Manual book	Flour cup	water cup	Cleaning scraper
1 pc	1 set (8 pcs)	1 pcs	1 pc	1 pc	1 pc

• These appliances are built to the very highest standards.
• There are no user-serviceable parts.

Follow these steps if the unit fails to operate:

1. Check the instructions have been followed correctly.
2. Check that the mains supply is functional.
3. If the appliance still does not operate, please contact us at Customer Service: frossvt@dg-sunrise.com
4. FROSSVT provides 24 months of warranty service and helps solve any product questions.

• Manufacture: FROSSVT Brands Inc
• Customer Service: frossvt@dg-sunrise.com

Documents / Resources

Frossvt H9 Electric Pasta Maker Automatic Noodle Making Machine [pdf] Instruction Manual H9 Electric Pasta Maker Automatic Noodle Making Machine, H9, Electric Pasta Maker Automatic Noodle Making Machine, Pasta Maker Automatic Noodle Making Machine, Maker Automatic Noodle Making Machine, Automatic Noodle Making Machine, Noodle Making Machine, Making Machine

References

• User Manual