Avigilon logo

Avigilon Control Center for IPVideo Corporation HALO IOT Smart Sensor

Avigilon Control Center for IPVideo Corporation HALO IOT Smart Sensor

This document has been compiled and published using product descriptions and specifications available at the time of publication. The contents of this document and the specifications of the products discussed herein are subject to change without notice. Avigilon Corporation reserves the right to make any such changes without notice. Neither Avigilon Corporation nor any of its affiliated companies: (1) guarantees the completeness or accuracy of the information contained in this document; or (2) is responsible for your use of, or reliance on, the information. Avigilon Corporation shall not be responsible for any losses or damages (including consequential damages) caused by reliance on the information presented herein.

Introduction

The Avigilon Control Center (ACC) system integration with the IPVideo Corporation HALO IOT Smart Sensor allows users to view and search for sensor detection events in ACC. Users can create rules and alarms around these sensor detections to alert operators or automate actions.

Requirements

  • Vendor: Requirements
  • Avigilon: ACC Server software 7.8 or later
  • Avigilon: ACC Client software 7.8 or later
  • Avigilon: ACC 7 POS license ACC7-POS-STR— 1 channel per HALO IOT Smart Sensor device
  • IPVideo Corporation: HALO IOT Smart Sensors
  • IPVideo Corporation: HALO Setup Tool.exe

Note: If you connect the HALO sensor as an RTSP stream to ACC, it needs one camera channel license in ACC.

For More Information
For more information about the procedures outlined in this guide, refer to the following specific software documentation:

  • Avigilon Control Center Client User Guide
  • Avigilon Control Center Server User Guide
  • HALO Installation Guide
  • HALO Quick Start Guide

Installation

Sensors

  • Install the HALO sensors according to the HALO Installation Guide.
  • Configure the sensor and detection events according to the HALO Quick Start Guide.

Servers

  • Install the ACC Server software on servers in your network.

Client

  • Copy the HALO Setup Tool.exeonto the desktop.
  • Install the ACC Client software on all client workstations.

HALO Configuration

After the HALO sensor events are configured, configure the Video Management System (VMS) Settings to send the events to the ACC system.

  1. In the HALO sensor web interface, go to the Messaging tab.
  2. Under VMS Settings, enter the following:
    • Set String — The text sent to the ACC server when an event is detected.
    • Reset String — The text sent to the ACC server when an event is no longer detected.
    • Address — The IP Address of the ACC server.
    • Port — The port number of the ACC server that is connected to the HALO sensor.
    • Protocol — Select TCP.
  3. Click Save: You will need the Set String, Reset String, and Port when configuring the ACC system

Important: In ACC, a POS transaction may not complete or end in some cases and ACC may have problems triggering rules and alarms when using events on single line sources. To avoid
inconsistencies with either live view or recorded view for transaction events, use \nat the end of Set String and Reset String. For example, enter halo.event.%EID%\nin the Set String field and halo.reset.%EID%\nin the Reset String field.

ACC Configuration

After the HALO sensor been installed, configure the ACC software for the integration.

  1.  In the New Task menu , click Site Setup.
  2. Select your server, then click POS Transactions
  3. Click Add.
  4. Complete the following, then click Next:
    • Hostname/IP Address: — The IP Address of the HALO sensor.
    • Port: — The port number of the ACC server that is connected to the HALO sensor
    • Connection Type: — Select Server.
  5. Select the Data Format for the source. This format will be used to recognize and capture the HALO sensor’s output.
    •  Click Add.
    • Edit the properties of your new format.
      • Name: — The name displayed under your list of formats.
      • Description: — A short explanation of the data and device.
      • Transaction Start Text: — The HALO sensor Set String.
      • Transaction End Text: — The HALO sensor Reset String.
      • Encoding: — The encoding used by the HALO sensor.
    • Use Capture Data to receive raw data. Verify that the event strings are being sent correctly.
    • Click Add Filter… to customize how the information is displayed in the ACC system. Default formats create line breaks and remove excess spacing.
    • Click OK to add the filter.
    • Click OK to save the data format.
  6.  Add Transaction Exceptions for text to monitor. You should add one exception per event. Using exceptions in POS transactions ensures a single device uses a single license. Creating multiple POS Transaction Sources with the same IP address and port configuration will only consume one license but only one of those multiple sources will work properly. To know more about adding transaction exceptions, see Adding Transaction Exceptions in the ACC Client User Guide.
  7. Click Next, then click Next again.
  8.  Select the cameras or devices to link directly to the HALO sensor and set the following, then click Next:
    •  Pre-Transaction Record Time: — How long to record before a transaction.
    • Post-Transaction Record Time: — How long to record after a transaction.
  9. Enter a name and description for the transaction source. Click Finish.

Note: You must create a new POS Transaction Source for each unique Halo device in the system.

Using the Integration

Now that the integration has been installed and configured, you can use the ACC system to create rules and alarms to monitor video detected by cameras that are connected to the HALO sensor.

  1. In the New Task menu , click Site Setup.
  2. Click the site name, then click Rules
  3. Click Add.
  4.  Select POS Transaction Events > POS transaction started or POS transaction ended checkbox, then click any transaction source.
  5. Select Any of the following transaction sources: and select a transaction source configured in the previous step. Click OK, then Next.
  6. Select any actions to respond to the event. Click Next.
  7. Add a Rule Name: and Rule Description:. The name should be unique throughout the ACC site.
  8. Assign a schedule.
  9. Click Finish.

Documents / Resources

aVIGILOn Avigilon Control Center for IPVideo Corporation HALO IOT Smart Sensor [pdf] User Guide
Avigilon Control Center for IPVideo Corporation HALO IOT Smart Sensor, Avigilon Control Center, Avigilon Control Center for IPVideo Corporation HALO IOT Smart Sensor

References

Leave a comment

Your email address will not be published. Required fields are marked *