Polycom RealPresence Access Director System
Polycom RealPresence Access Director System Server Setup
The sections below describe the steps required to perform the initial installation and setup of a Polycom® RealPresence® Access Director™ system.
At the end of this procedure, you will have successfully logged into the RealPresence Access Director system and be ready to finish configuring the system.
Collect the Necessary Materials
Before you install a RealPresence Access Director system, collect these materials:
- The RealPresence Access Director system server shipment
- The completed First-Time Setup Worksheet
- A PC running Microsoft® Windows® with:
- Hardware
- 1280×1024 (SXGA) minimum display resolution; 1680×1050 (WSXGA+) or greater recommended
- USB and Ethernet ports
- Software—Supported versions of the following software
- Microsoft® Windows®
- Microsoft Internet Explorer® v8 or 9
- Adobe® Flash®
- Hardware
- • 1 blank USB memory stick on which you can install the RealPresence Access Director system USB Configuration Utility, which you can download from support.polycom.com.
Note:
- Install and run the USB Configuration Utility only on the blank USB memory stick shipped with the RealPresence Access Director system.
- The USB memory stick must have a FAT32 file system.
- The USB Configuration Utility may not complete correctly if the USB memory stick has been used previously or has multiple partitions.
Documentation Resources
In addition to this guide, the available documentation that describes the RealPresence Access Director system includes:
- RealPresence Access Director System Release Notes
- Polycom RealPresence Access Director System Administrator’s Guide
- Polycom RealPresence Access Director System Deployment Guide
- Online help. In the management interface, select Help to access the entire online help system.
To access these documents, go to support.polycom.com
Complete the First-Time Setup Worksheet
Before you begin system setup, fill out the My System Values column of this worksheet.
First-Time Setup Worksheet
| Configuration | Description | Value |
| Network_Domain = | Identify the domain in which this system is operating. | Domain name |
| Network_DnsServers_IP_1 = | Identify the IP address of the Domain Name Server for the network to which the system is connected. | DNS IP address |
| Network _Interfaces_Interface_1_name = eth0 | NIC name | Always eth0 |
| Network_Interfaces_Interface_1_Ip_bootProto = static | NIC boot protocol | Always static |
| Network_Interfaces_Interface_1_hostname = | Identify what is to be the hostname of this system. | Hostname |
| Network_Interfaces_Interface_1_Ip_address = | Identify the IP address for this system. | IP Address |
| Network_Interfaces_Interface_1_Ip_gateway = | Identify the default gateway for the network to which this system is connected. | IP Address |
| Network_Interfaces_Interface_1_Ip_netmask = | Identify the netmask for the network to which this system is connected. | Netmask |
Unpack and Install the Hardware Components
The RealPresence Access Director system uses a Polycom-branded Dell server.
To unpack and install the hardware
- Examine the shipping container for damage. If you find damage, file a claim with the delivery carrier. Polycom is not responsible for damage sustained during shipment of this product.
- Open and review the container packing slips.
- Open the container and examine the contents. The system server package includes these items:
- The Polycom RealPresence Access Director system server
- The Polycom RealPresence Access Director System Quick Start Guide
- Power cord
- Rack-mount kit
- Bezel assembly and key
- Polycom RealPresence Access Director system recovery DVD (included for recovery purposes; this software is already installed on the server)
- A USB memory stick with server diagnostic utilities (to be used only under the direction of Polycom Global Services)
- The server Product Information Guide
- Examine the contents for damage. Again, if you find damage, file a claim with the delivery carrier.
- Unpack your system and identify each item. Keep all shipping materials in case you need them later.
- Assemble the rails and install the server in the rack. To rack-mount a server, see the Rack Installation Guide (available at
http://support.dell.com/support/edocs/systems/peR620/en/index.htm). - Install the RealPresence Access Director system.
- Connect the system’s power cable(s) to the system and, if a monitor is used, connect the monitor’s power cable to the monitor.
- Plug the other end of the cable into a grounded electrical outlet or separate power source such as an uninterrupted power supply (UPS) or a power distribution unit (PDU).
- Press the power button on the system and the monitor. The power indicators should light.
- (Optional) Install the bezel.
- Connect the GB 1 Ethernet port to the enterprise network. This is the eth0 network interface, which must be used for this purpose.
Basic System Configuration
Choose one of the following options to configure the RealPresence Access Director system server.
- Configure the System Using the USB Flash Drive
- Configure the System Without the USB Storage Device
Configure the System Using the USB Flash Drive
To configure the system using the USB flash drive
- At a PC system, download the Polycom RealPresence Access Director USB Configuration Utility from support.polycom.com.
- Connect the blank USB memory stick to the Windows PC on which you put the ZIP file containing the USB Configuration Utility.
- Unzip the USB Configuration Utility files to the USB memory stick. The USB Configuration Utility files must be at the root of the drive, not in a folder.
- Start the USB Configuration Utility by double-clicking usb-gui.exe.
- Enter the network values from the “First-Time Setup Worksheet” on page 2, and click Save. The script saves a lan-cfg.txt file to the root of the USB flash drive.
- In your system tray, click Safely Remove Hardware and select Safely Remove USB Mass Storage Device. When a message tells you it’s safe to do so, disconnect the USB flash drive from the PC.
- On the RealPresence Access Director system server,
- Turn on the system server and insert the system recovery disk.
- Insert the USB stick into one of the server’s USB ports.
- Reboot the system server. The server boots from the DVD, and the installation starts. About 15-20 minutes later, the DVD ejects and the server reboots. After it reboots, the server reads its network settings from the USB stick and applies them.
- On a PC with network access to the RealPresence Access Director system, point your browser to the system’s IP address (https://:8443/) and log in with user ID admin and password admin. The RealPresence Access Director system’s management interface appears, displaying the Dashboard. From its menus, you can complete your system setup. See “Advanced System Configuration” on page 7 to identify the tasks required to finish the system configuration.
Configure the System Without the USB Storage Device
To configure the system settings manually
- Turn the system server on.
- At the system prompts, configure the following settings. To display available default settings, press ENTER at each prompt.
Prompt Default Setting Enter the RealPresence Access Director system hostname rpad Enter the system domain name Enter the system host IP address 192.168.1.254 Enter the Default Gateway for the system 192.168.1.1 Enter the Netmask for the system 255.255.255.0 Enter a DNS for the system 198.168.1.100 - Press ENTER to complete the basic configuration. The system server reads the configuration settings and finishes the basic system configuration.
- On a PC with network access to the RealPresence Access Director system, point your browser to the system’s IP address (https://:8443/) and log in with user ID admin and password admin. The RealPresence Access Director system’s management interface appears, displaying the Dashboard. From its menus, you can complete your system setup. See “Advanced System Configuration” to identify the tasks required to finish the system configuration.
Advanced System Configuration
Once you have completed the basic system configuration, see the Polycom RealPresence Access Director System Administrator’s Guide to complete the more advanced system configuration.
The following table lists the recommended order for completing the configuration of the RealPresence Access Director system. For detailed instructions on performing these tasks, see Chapter 3 of the RealPresence Access Director System Administrator’s Guide.
| Tasks |
| Set the system time |
| Configure the network interface settings |
| Connect to the Polycom management system |
| Manage the system certificates |
| Connect to Microsoft Active Directory |
| Configure the access proxy settings |
| Configure the SIP and H.323 signaling settings |
| Configure the media traversal settings |
| Configure the federation settings |
Trademark Information
POLYCOM® and the names and marks associated with Polycom’s products are trademarks and/or service marks of Polycom, Inc., and are registered and/or common law marks in the United States and various other countries.
All other trademarks are the property of their respective owners.
Patent Information
The accompanying product may be protected by one or more U.S. and foreign patents and/or pending patent applications held by Polycom, Inc.
© 2012 Polycom, Inc. All rights reserved.
Polycom, Inc.
6001 America Center Drive
San Jose CA 95002
USA
No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of Polycom, Inc. Under the law, reproducing includes translating into another language or format.
As between the parties, Polycom, Inc., retains title to and ownership of all proprietary rights with respect to the software contained within its products. The software is protected by United States copyright laws and international treaty provision. Therefore, you must treat the software like any other copyrighted material (e.g., a book or sound recording).
Every effort has been made to ensure that the information in this manual is accurate. Polycom, Inc., is not responsible for printing or clerical errors. Information in this document is subject to change without notice.
Documents / Resources
 |
Polycom RealPresence Access Director System [pdf] User Guide RealPresence Access Director System |
Support | Dell US 
support.polycom.com 
